Search Documents

By Javier Enrique Basurco Cayllahua

In this work, a gram-positive bacteria was used as biosorbent to elucidate the aluminum load capacity under different conditions related to metallurgical and chemical plants. The sorption data followed the Langmuir, Freundlich, Dubinin-Radushkevich isotherms. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Dubinin-Radushkevich model fits better the aluminum biosorption data. The maximum sorption capacity was found to be 41.59 mg.g-1. The maximum removal of aluminum was 95% at pH around 5. The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). This study indicated that the R. opacus is an environmental friendly biosorbent.

Jan 1, 2009

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"In the present study classical induction design tools are applied to the problem of heating nonmagnetic metal billets, using 50 Hz AC. As an example of great practical industrial interest, the induction heating of aluminum billets is addressed specifically. The predicted work piece power is compared with the measured work piece power for a long and a short coil, using well established methods, such as those of Burch and Davis, introduced in 1926/28, Dwight and Bagai in 1935, Baker in 1944/57, Vaughan and Williamson in 1945, and by Tudbury in 1960. A calculation methodology based on a combination of the available tools is also introduced and discussed. The method has proven to give an error of <10% of the actual work piece power. An equation for Tudbury's work piece shortness correction factor is disclosed for the first time.IntroductionInduction heating of metal billets is a practical problem, with a geometry suitable for solution using analytical methods. This paper will examine solutions related specifically to round work pieces in round coils, although the methods presented can be extended to other regular shapes of work pieces and coils[l]. The methods can also be extended to ferromagnetic materials with slight changes[2-3]. It is assumed that the coil and work piece have a consistent diameter over their entire length and that the work piece is at least as long as the coil. Correction factors can be derived for the cases where the work piece is shorter than the coil.The study of induction heating by coils began in the late 19th century with theoreticians like Heaviside[ 4]. The work of Burch and Davis[ 5-7] in the 1920' s greatly improved the theoretical understanding of induction applied to metallurgy. Many investigators in the 1930's-1950's: Dwight and Bagai[8], Baker[l-2, 9], Vaughan and Williamson[3, 10] and others[l 1-12] added to our understanding with clearer mathematics, solutions for specific applications, semi-empirical modifications and practical design tools. Much of the accumulated knowledge is available in books, such as Tudbury's practical text or Simpson's engineering guide from 1960[13-14]. Perhaps the best description and derivation of the theoretical and semi-empirical solutions can be found in Davies[15]."

Jan 1, 2011

By Vianey Garcia-Osorio

One of the problems in the carbothermic aluminum process is the substantial loss of aluminum compounds as vapors due to the high temperatures in the process. In order to solve this problem a Vapor Recovery Unit (VRU) is proposed. In this unit operation the aluminum vapor undergoes a series of heterogeneous non-catalytic reactions forming solid, liquid and gas products. In this work a model for the simulation of this unit was developed which includes heat and material balances as well as heterogeneous non-catalytic reactions. The model leads to a system of differential equations; its solution was implemented in Matlab giving as a result a stage-by- stage solid-fluid reaction model.

Jan 1, 2001

By J. Wendt, P. R. Sahm, T. Uloth, M. Weck, F. Foertsch

"The FEM program systems CASTS (Computer Aided Solidification TechnologieS) (1) and FINELF (FINite ELement Frontal Solver) are used to optimize a thin walled die casting. After a short description of the programs it will be worked out how to use them not only for simulating solidification processes but also for optimizing the design of workpieces. The calculations will be done for an automobile's support bracket which is manufactured in a well known car factory in Stuttgart, FRG.IntroductionAt the Aachen Foundry Institute the software package CASTS was developped to simulate solidification of castings. In order to optimize the whole manufacturing process it does not appear sufficient any more to take into account only the specific aspects of casting. For instance one has to consider additionally the stress situation under service load. For this reason the Foundry Institute together with the Aachen WZL-Institute (Machine Tool Laboratory) and the car factory mentioned above started to probe into a first step in that direction. Figure 1 shows the support bracket which shall be optimized."

Jan 1, 1986

By M. Drozd

Multi-use pad operators require an efficient and economic method to destroy cyanide in their process residues so new material can be stored on the pad and leached. Operators of the dedicated or single-use pads require an effective cyanide destruction method for pad closure. Cyanide destruction can be accomplished by utilizing oxidants such as hydrogen peroxide or calcium hypochlorite, or by utilizing ferrous sulfate which sequesters the cyanide in strong acid dissociable complex. Ferrous sulfate can be the preferred method of cyanide destruction because it is a less costly chemical, reaction rates are almost immediate and unlike oxidants, it can penetrate the total depth of a pile without being destroyed by side reactions. Literature indicates that the (Fe(CN)6)-4 com~lex is produced slowly but it appears that complexes such as Fe(CN)4(H20)2-or Fe(CN)4(OH)2)-4, are formed quickly and should have no U.V. sensitifity, unlike (Fe(CN)6)-4. Stoichiometry of the testwork indicates that Fe«CN)4(OH)2)-4 complex may be the species formed. The usage of ferrous sulfate has the advantage of being able to bring ~ level down that divalent metal ions such as Cu++, Cd++, Hg++, Pb++ and Zn will form insoluble complexes and precipitate from solutions does not destroy weak acid dissolvable complexes and can leave a heavy metal problem behind after cyanide destruction.

Jan 1, 1990

By André L. B. Bittencourt

The copper content in the waste slag represents the greatest loss in the process of Caraíba Metais&apos; Smelter. By identifying the variables responsible for copper stabilization in the slag, a minimization on these losses is expected, producing a granulated waste slag with a copper content lower than 0.7%. Statistics resourses such as control charts, Pareto&apos;s diagram and correlations curves were applied for the data obtained in the first semester of 1992. The magnetite and the calcium oxide contents in the slag of the Flash Smelter Furnace were most prominent variables. Some operational changes introduced during and after this investigation have shown good results.

Jan 1, 1994

By C. Díaz

Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulfur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is heated in a sulfuric acid plant, and the low sulfur calcine is reduction smelted with coke in an electric furnace to yield a sulfur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulfur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries are obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco&apos;s Thompson Smelter, and its key operating parameters.

Jan 1, 1993

By J. D. McCain

Magma&apos;s San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

By He De-wen

The influence of wastewater containing benzene from chemical industry by technology combined blow-off with Fenton reagent oxidation was experimentally studied. The present results suggest that the technology combined blow-off with Fenton reagent oxidation can effectively remove benzene pollutant in wastewater. The main factors that influence the removal benzene such as temperature and blowing time and volume, pH and reagent dosage of H2O2 and Fe2+ are studied and the optimal experimental conditions are as follows: time 20min, temperature 40i, air-blowing volume 0.4L/min, pH value 5, and H2O2 and Fe2+ dosage 2mL/L and 200mg/L respectively. Under the above conditions, benzene pollutant can be removed up to 97%. Compared to other removal ways of wastewater containing benzene, the technology combined blow-off with Fenton reagent oxidation is more effective and has the advantage of high speed.

Jan 1, 2009

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By J. Antrekowitsch

Keywords: residues, fluorides, chlorides, zinc, steel mill dust The recyclability of various nonferrous metal wastes often suffers from a relatively high fluorine and chlorine content. Both are inserted in most cases by the use of plastic contaminated scrap and a wide variety of different coatings. These halogens lead to poor product qualities and off gas contamination. Especially the history of zinc recovery from steel mill dusts shows, that the today common hydrometallurgical options are on their limit and therefore are not sufficient in most cases. This thermochemical study should give more information about different pyrometallurgical options, that offer both a chlorine and fluorine reduction and efficient zinc recovery, preferably in one process step. Selective evaporation in different atmospheres and conversion with the use of hydrogen are the main parts in this study. The results combined with the relatively small information available from literature should provide a basis for further investigations in this field.

Jan 1, 2005

By M. C. Flemings, S. B. Brown

"Metallurgy, as all of material science and engineering, rests on the intellectual foundations of processing-structure-property-performance relationships. Today it is widely recognized that processing has been too long neglected and presents exciting opportunities for exploitation. New processes, many of them already in the laboratory, will be exploited in the year 2000 and beyond, for near net shape forming and for achieving-new metallurgical structures and composite structures. Process modelling will alter the way we think about process and product design. Processes themselves will increasingly be automated and controlled by computers, altering the nature of the workplace and the tasks of the metallurgical engineer of the future. IntroductionInnovations in metal processing is hardly a new phenomenon, with the field thousands of years old. Nonetheless, the next few decades offer particularly important opportunities to improve our ability to process these materials. We appreciate today the variety of processing paths available to us, including vapor-, plasma- and electro-deposition, multiple phase and casting technologies, and non-equilibrium processes, and how these affect structure at the atomic level and at higher levels of aggregation. We understand the basic physical mechanisms involved far better than even before and have remarkable new abilities to predict, control, and simulate the kinetics underlying processes, and the processes themselves.The following sections describe these new opportunities in greater detail. First, we examine developments in the modelling of metal processing. We then consider some implications associated with process control and automation. Finally we present what we consider to be particularly promising metal processing technologies, and conclude with a few summary comments."

Jan 1, 1988

By Chen Song

Keywords: Mixed extractant, Copper, Cobalt, Nickel, Synergistic effect During separation process of copper and cobalt from nickel sulphate solution, the effects of constitutions and compositions of mixed extractant D2EHPA and PC88-A or Cyanex 272, has been studied. In one step extraction cycle, the following results are obtained:[Ni]/[Co]>4000 and [Ni]/[Cu]>40000 in nickel sulphate solution, [Co]/[Ni]>1000 and [Co]/[Cu]>30000 in cobalt chlorinate solution, [Cu]/[Ni]>10000 and [Cu]/[Co]>200 in copper sulphate solution. It was elucidated that the above-mentioned synergistic mixtures can effectively separate cobalt and copper from nickel sulphate acid solution and achieve a greater synergistic effect.

Jan 1, 2005

By De-wen He

The distribution of persistent organic pollutants in the environment is studied using the multimedia environmental fugacity model, and environmental health risk assessment of POPs nearby a copper smelt enterprise is carried out. The result indicates that all are in an agreeable risk level without exception. The annual individual chronic risk index of HCB is 7.50×10-11. The annual individual risk index of 3,3&apos;,4,4&apos;-TCB is 1.57×10-9, and the annual individual risk index of 2,3,7,8-TCDD is 6.57×10-9.

Jan 1, 2009

By W. G. Davenport

Chapter 1 showed that flash smelting is a key step in extracting copper from sulfide ores. It also showed that there , are two versions of flash smelting: (a) Outokumpu flash smelting, which uses oxygen-enriched air blast and injects dry feed downwards into a hot furnace (b) lncoflash? smelting, which uses industrial oxygen blast and injects dry feed horizontally into a hot furnace. This chapter describes Outokumpu flash smelting.

Jan 1, 2001

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental&apos;s Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By B. L. Chulu

In the carbothermic reduction of lead sulfate to produce lead, the inclusion of soda ash (Na,CO,) in the charge provides for the control of sulfur dioxide in the effluent gas. An important mechanism in the process appears to be the carbothermic reduction of the sodium carbonate whereby sodium gas and carbon monoxide are produced. These intermediates then participate in the reduction of the lead sulfate to produce lead metal and stable sulfur species in the molten slag phase. In addition, there is some evidence that the presence of lead metal in the charge may also serve to increase the lead recovery in the process. These aspects were investigated by conducting laboratory-scale smelting tests with small charges (;3g), at 1173°K(9000C). Recovery did not exceed 74w% and the role of incipient lead metal in the charge could not be clearly assessed.

Jan 1, 1993

By Rudolf Keller

"EMEC Consultants is developing a process to extract oxygen, aluminum and silicon from lunar anorthositic soil. The process will provide oxygen in space for propulsion, aluminum as a structural material, and possibly silicon for the construction of solar cells.The evolution of the process concept in the course of our present NASA-sponsored SBIR effort is discussed. A molten salt electrolysis producing aluminum and oxygen is the central step; inert anode technology is to be employed. Silicon will be produced by reducing the anorthite, CaAI2Si20S' with aluminum. In a steady-state operation, all components of the ore added have to be removed from the process, and the removal of calcium is a major topic of our experimental studies.Utilization of Lunar ResourcesUtilization of lunar resources may play an essential role in the exploration of the solar system and the conquest of space. High costs are involved in overcoming Earth's gravity to supply missions in space. Even at a low projected cost of $ 300 for transporting a pound of payload into Earth orbit -- today's costs are many times higher -- it appears attractive to use resources in space to produce needed materials. Processing of lunar resources on the lunar surface is an obvious possibility.Oxygen is a product of major interest. It is required for support of human life in space. Even greater quantities may be needed for propulsion, to conduct further missions into space. To satisfy this demand for oxygen through lunar processing requires a quite different solution than to supply oxygen on Earth, where oxygen gas is abundant and easy to extract from air or water. On the lunar surface, solid oxide materials have to be used. Hydrogen reduction of ilmenite and subsequent electrolysis of the resulting water is being studied [1]. Other suggestions include fluorination of lunar soil [2], reduction with lithium and electrolytic decomposition of the resulting lithium oxide [3], and aqueous HF leaching [4]."

Jan 1, 1988

By J. G. Eacott

This paper reviews the role of oxygen potential and the advances that have been made in the application of tonnage oxygen in copper smelting. Brief reference is made to reaction kinetics before attention is turned to the thermodynamic considerations in copper melting to illustrate the importance of oxygen and. oxygen potential in the component parts of the overall smelting process. The chemical potential diagram for the Cu-Fe-S-O-Si02 system is used to elucidate the difference b etween the conventional matte smelting process and the modern continuous processes. A progressive oxidation scale&apos; is constructed to show the common elements which exist, and the matte grades produced, during the smelting of concentrates to blister copper in commercially available copper smelting processes and those under development. The common route in producing blister copper from molten mattes, regardless of process, is illustrated on the Cu-Fe-S equilibrium phase diagram. The essential features of oxygen enrichment, in terms of its effect on combustion conditions (i.e. oxidation of fuel and sulphide minerals) and the heat balance are outlined. The benefits of oxygen enrichment are listed. The influence of tonnage oxygen and its effect on productivity, fuel savings, gas volume and strength in various copper melting processes are examined as a state-of-the-art review. Reference is made to the economics of tonnage oxygen utilization.

Jan 1, 1983

By He De-wen

The municipal solid waste is a by-product of the daily life of urban residents. The quantity and ingredients of municipal solid waste has exceeded the current management and disposal ability, which has done a great harm to municipal environment and sanitation quality and threatened people?s health. On the basic of analysis on the amounts and main elements of municipal solid waste of Changsha City, the sanitation landfill, incineration, composting, reclamation and utilization technology of household waste were compared specifically in this paper. Based on the concrete conditions of Changsha City, the paper has proposed a disposal proposal combined with reclamation and landfill of municipal solid waste of Changsha City, and the environmental benefit, social benefit and economical benefit of the prepared processing routes were also analyzed in the paper.

Jan 1, 2009