Search Documents

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By Esa J. Peuraniemi

Copper smelting to form blister in one single step has been possible for a long time even from low grade concentrates. In spite of obvious benefits, it has been economically viable only with few special raw materials having high enough Cu/Fe and Cu/S ratio. Outokumpu Blister Flash Smelting is currently applied at three operations, and three others will be commissioned in the near future. With typical chalcopyrite concentrates two main obstacles have prevented wider adaptation of direct blister processing: slag formation and heat generation. Oxygen potential in the reaction shaft must be high in order to produce blister with targeted sulfur content below 1%. When large amount of iron is oxidized, as well as sulfur, copper is inevitably also oxidized into slag. High copper amount in substantial tonnages of slag lead on to costly down stream recovery operations to obtain discardable slag. Almost complete oxidation of sulfur and iron releases a high amount of heat which traditionally has been solved by lowering oxygen enrichment of the blast leading on to oversized off-gas line and acid plant. One challenge in direct blister smelting relates to the attack of aggressive high-copper containing slag against furnace refractory lining. In continuously operated Outokumpu Direct Blister Flash Smelting this is taken care of by preventing vigorous melt movement in the settler. Stable bath conditions and stationary slag against refractory lining enable the formation of a protective autogenous layer between aggressive slag and vulnerable refractory. These direct blister smelting challenges are addressed from equipment and process development point of view. New solutions to overcome the obstacles are presented and discussed.

Jan 1, 2006

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By Biserka Lucheva, Tzonio Tzonev

"A unique DC electric arc rotary furnace with capacity 150 kg has been designed and constructed for the recycling of low-quality scrap and aluminum dross. The main constructive feature of this furnace is that the axially positioned graphite electrodes (cathode and anode) are placed 100 mm away from the rotation axis of the furnace. A specific characteristic of the construction is the possibility one of the electrodes (the anode) apart from moving axially (parallel to the furnace axis) to move at 90° outside the working space. High recovery rate of metal aluminum from aluminum dross (92%) was realized in this furnace. This is the reason for construction of industrial DC electric arc furnace.IntroductionThe consumption of aluminum waste has been rising continuously on a world scale, which is a great stimulus for the development of the technology for aluminum recycling.To recover the aluminum in dross, the conventional recycling process uses salt rotary furnaces heated with a fuel or a gas burner. This treatment process produces a secondary dross containing alumina, salts, impurities and a small amount of aluminum. Molten aluminum is tapped from the furnace and the residue is then dumped from the furnace. It has been the practice to dispose the residue in a landfill. Improvement of this technology, known as the oxy-fuel process, uses a gas burner enriched with oxygen to increase the thermal efficiency [1]. Recent studies show that the most efficient aggregate for recycling of aluminum scrap has turned out to be the rotary tilting furnaces, heated by plasma or electric arc, for which the use of flux is not necessary [2,3].Accordingly, there is a substantial need in the industry for an improved process for recovering free aluminium. It is particularly desirable that such process be cost effective and ecologically safe."

Jan 1, 2008

By Cam T. Nhan

The potential use of coal fly ash as a construction material has been recognized for many years,. In this work, an admixture of the ash residue is investigated for use as a landfill liner. In particular, its performance as a chemical barrier to the leachate from the municipal solid waste (MSW,) is determined. The test specimens are a water compacted admixture of class F fly ash, low in calcium content, which is blended with lime dust and calcium bentonite. MSW is passed through the compacted fly ash specimens under a gravitational head. The. diffusion of elements in the leachate through this material is monitored as a function of time. The distribution profiles of the retained elements in the compacted admixture provide prediction of the long term performance of the compacted admixture directly affect the leachate diffusion rate, hence, the mobilities of the retained elements.

Jan 1, 1992

By Georgeta Rata, Cornelia Petroman, Ioan Petroman

"Proper training and education in the field of recycling and waste treatment are inconceivable without the proper teaching of the terminology specific to both recycling (aerospace products recycling, automotive recycling, general recycling, recycling behaviour, recycling schemes, recycling systems, and waste recycling) and waste (characterization of waste, electronic waste, heavy-metal containing waste, monitoring of waste, radioactive waste, solid waste, waste collection, waste conversion, waste recycling, waste reutilization, waste stabilization, waste storage, and waste treatment) in both the students’ mother tongue and in English for Special Purposes (ESP) as a second language (with focus on the structuring of the specific terminology). Including linguistic approaches among the possible approaches of environmental protection and material sustainability means including linguistics among the various disciplines addressing energy supply, cement and building materials, metallurgy, chemistry, glassware, pulp and paper industry, machinery, automobile and electronic industries, collection, and sorting, further treatment and final disposal of post-consumer material.IntroductionCultural and technical changes have produced more novel artefacts than novel activities or novel properties, generating new vocabulary needs that are readily answered by new words (nouns).The purpose of this research is to show that ‘waste words’ – phrasal words (items that have the internal structure of phrases but function syntactically as words, e.g., cattle waste) and particularly compound nouns (words formed by combining roots, that tend to have a meaning that is more or less idiosyncratic or unpredictable, e.g., wastepaper ‘discarded paper’) – used in the study of the English of recycling, waste treatment, and clean technologies can be misleading for both native and non-native students and/or users of English because their structure alone does not allow instant, proper understanding of their meaning.Our hypothesis is that this inconvenient can be overcome by getting to reach the proper meaning of these new words. Or, arriving at the precise meanings of the ‘waste words’ depends on our knowledge of the world (for example, wastepaper indicates that some used paper is discarded and not wasted) rather than on purely linguistic knowledge."

Jan 1, 2008

By Christian Ludwig, Virginie Silberstein, Rizlan Bernier-Latmani, Simona Regenspurg

"Residues from waste incineration (bottom ashes) form large amounts of heavy metal-rich waste. Theoretically, heating and the addition of chloride to the ashes could remove these metals by formation of volatile metal chlorides. The remaining heavy metal-poor ashes could be used, for example, as cement additives. In the proposed process of our study we used bypass dust from the cement industry as chloride additives to the bottom ashes. We aim to determine experimentally the optimal conditions to remove heavy metals from ashes and to simulate this process by thermo- chemical modeling. In our experiment we investigate heavy metal flows by heating of differently composed mixtures of bottoms ash and bypass dust in dependence of different furnace temperatures (500-1200 °C). Furthermore, we investigate the reactivity (leaching characteristic) of the resulting product in order to predict if secondary residues can be landfilled in agreement to Swiss regulations for inert materials.IntroductionThe incineration of garbage is generally considered as the most environmentally friendly method for the reduction of municipal solid waste. This is because, compared to traditional storage of waste on landfills, incineration produces less greenhouse gases and destroys toxic organic compounds. The released exothermic energy can be recuperated and the residues from the combustion chamber (bottom ash) are strongly reduced in volume. However, they still form about 600 kt of waste per year in Switzerland, which needs to be landfilled. However, these residues could be potentially used as construction materials after mechanically recovering ferrous and non-ferrous metals. However, the resulting ashes (discharged dry or wet) still contain increased amount of heavy metals (exceeding state regulation) requiring them to be finally deposed on a hazardous waste site. A thermal treatment of these ashes could enable both, to separate and recuperate the remaining heavy metals and an inorganic heavy-metal poor material. The evaporation of metals depends on temperature and can be lowered by addition of chlorides, which would lower the boiling point of most metals by formation of metal chlorides (table 1). 745"

Jan 1, 2008

By S. Vukcocic

A long term research project is in progress to establish the parameters of an acid leach process to recover alumina 'froui' high-iron and/or low-iron white bauxites, kaolinite, coal. ash and copper mine tailing. In this paper the results of acid leaching of copper flotation tailing for the removal of alumina are presented. The tailing is very complex material which contains 25% Al203 in the -10 lim fraction. X-ray diffraction indicates presence of quartz, kaolinite and minor 'alunite. After classification and ,separation of the -10 lim fraction, the raw material is fired to 550GC and leached at 90GC. Filtration is applied for the separation of white silicate residue form leach liquid. After the purification step, aluminum salt is crystallized from the solution, and calcined to alumina. Kinetic correlation and regime, of the processes are defined and presented in the paper.

Jan 1, 1992

By Yang Tian-zu

Sodium pyroantimonate which is widely used as the clarifier in the glass industry and as the synergist in anti-flaming industry respectively has a production history of about 30 years in China. At present there is the production capacity of about 20,000 tons per year in China and China is chief producer of sodium pyroantimonate. In this work the production processes adopted by the producers of China, the operation conditions and the product qualities of sodium pyroantimonate prepared by different preparation methods have been summarized, and on the basis of comparing the advantages and disadvantages for each process the most advanced method - the air-oxidation method was introduced in detail. The production processes of sodium pyroantimonate mainly include the method of oxidation by sodium nitrate, the oxidation method of hydrogen peroxide, the potash salt method, the chlorination method and the air-oxidation method etc. The method of oxidation by sodium nitrate in which the crude antimony oxide, sodium carbonate and sodium nitrate are separately used as the raw material, the flux agent and the oxidant, has the advantage of short and simple technological process, but low grade quality of sodium pyroantimonate and bringing about serious environmental pollution are the disadvantages and this method has been substituted by other methods. Sodium pyroantimonate can be directly prepared by the hydrogen peroxide oxidation method with the advantages of simple technological process, high grade quality of the product and little environmental pollution. High grade quality of sodium pyroantimonate can be also synthesized by the potash salt method, in which industrial antimony white, the hydrogen peroxide, potassium hydroxide and sodium hydroxide are applied as the starting material. The disadvantages of these two preparation methods are high production cost and high requirements on the raw materials. The chlorination method with the crude antimony oxide, hydrochloric acid and chlorine as the raw material has the advantages of low production cost and high grade quality of the product. However complex process, high requirement of anti-corrosion for the equipments and producing plenty of waste water limit its application. The air-oxidation method with stibnite/jamesonite concentrate, sodium sulfide, and sodium hydroxide as the raw material and atmosphere as the oxidant is a newly developed method and its advantages are low production cost and the complex raw material can be treated by this method and its disadvantage is that the quality of sodium pyroantimonate is lower than that prepared by the oxidation method of hydrogen peroxide and the potash salt method.

Jan 1, 2006

By Michael E. Stout

The recovery of the constituent components of spent lead acid batteries was pioneered in the early 1970's by M.A. Industries, Inc. MA's main reason for research and development in this area was to recover the polypropylene casings for use as feed stock in their injection molding plants. At that time spent and reject casings were either disposed of or being fed with the lead 'bearing materials into the ,smelting process. M.A. has since developed, built and operated plant for the conversion of scrap casing into reusable copolymer resins. The system is composed, of washing, .sizing, extrusion and pelletizing the polymer into a form which is ready to be injection molded into new products.

Jan 1, 1995

By D. A. R. Kay

Phase stability diagrams are used to predict the abilities of lanthanum and cerium oxides to desulfurize coal gasification products in the temperature range 800-1000 C. Results of desulfurization studies in laboratory fixed bed reactors illustrate the effects of i) sorbent preparation, ii) input gas quality and iii) temperature, on the desulfurization reaction. 2CeO(2-x)(s) + H2S(g) + (1-2x)H2 = Ce2O2S(s) + 2(1x)H2O(g) The results of desulfurization/oxidation regeneration cycles are also reported.

Jan 1, 1989

By Andreas Nolte

In 1999 HÜTTENWERKE KAYSER AG (HK) in Germany will produce more than 180,000 t/y of electrolytic refined copper. To achieve this production from materials with copper grades from two to seventy percent and diverse copper alloys, HK operates three blast furnaces, one holding furnace two Peirce Smith converters and two anode furnaces. Technical, metallurgical and economic factors for the ongoing process optimization are outlined. The fluctuating quality and quantity of raw materials renders complex this optimization. The principal variables are the quality and quantity of process consumables: coke, copper-iron, limestone, oxygen, as well as the blending of feedstock and a new organization of the operating crews. The search for new metallurgical process parameters is ongoing. HK started with an intensive research programm in November 1997. As a result it will be possible to cut processing costs by about ten per cent, to increase the blast furnace capacity by ten per cent and to lower the metallurgical losses of copper and tin in the slag by more than ten percent. The presentation concludes with information on future steps to continue the optimization process.

Jan 1, 1999

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By J. L. Bill

The capacity of the Mount Isa Mimes Limited Copper Smelter was expanded in 1998 from 180,000 tomes per year of anode copper to 265,000 tpy. It is based on the innovative Copper ISASMELT technology, which currently treats concentrate at up to 184 tph. Increasing lance-air oxygen enrichment increased the ISASMELT furnace feed rate from 102 to 184 tph. The increased feed rate was achieved without any modifications to the ISASMELT furnace. The first refractory campaign following the upgrade lasted for two years. Future campaign lives of four years or more--without water cooling-are possible. Other Copper ISASMELT furnaces are operating in the U.S.A., Belgium, and India, with additional smelters under construction in China and Germany. In addition, Lead ISASMELT furnaces are operating in the U.K. and Malaysia. The paper discusses the performance of the MIM Copper ISASMELT furnace and the Copper Smelter since the expansion, including operating data and refractory performance.

Jan 1, 2002

By V. Kamavaram

Ionic liquids are novel salts used as potential non-aqueous electrolytes for aluminum electrolysis at low temperatures. In the current research di-alkylimidazolium chloride ionic liquids such as 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) and 1-hexyl-3-methylimidazolium chloride ([HMIM]Cl) were investigated for aluminum electrolysis. Melt formed by mixing ionic liquid with AlCl3 is termed as chloroaluminate and is composed of several polymeric chloroaluminate anions. Ionic liquids are studied as electrolytes for aluminum electrowinning and electrorefining of aluminum based materials (A356, A360, & Al-MMC) at low temperatures. Mechanism of aluminum electrodeposition in these chloroaluminate ionic liquid electrolytes was investigated using electroanalytical techniques such as cyclic-voltammetry and chronoamperometry. Aluminum electrodeposition on pure copper substrate in AlCl3-[BMIM]Cl (1.5:1.0) electrolyte at 30°C melts was found to be quasi-reversible process with a charge transfer coefficient ( of 0.40. Chronoamperograms obtained at different voltages in the range (-0.1 to -1.0 V) revealed that the initial stages of aluminum deposition in AlCl3-[BMIM]Cl melts was instantaneous nucleation followed by diffusion controlled growth of three-dimensional aluminum nuclei. The diffusion coefficient of electroactive species Al2Cl7¯ in AlCl3-[BMIM]Cl melts was found to be 6.5×10-7 cm2 s-1 from Cottrell?s equation and 3.9×10-7 cm2 s-1 from the dimensionless current-time transients.

Jan 1, 2006

By R. T. Hernández, I. Hilerio, A. Altamirano, M. A. Barrón

"The principal objective for finishing surfaces is to protect and/or to decorate them. This can be achieved by adding or removing material from the work surface. The addition of aggregated material is called coating or recovering. In this work, mecano-chemical techniques are investigated for surface finishing. For these techniques, barreling or polishing by the friction method will be used. These are the cleaning or finishing processes most used for great volumes of small pieces. These methods improve the surface finishing by eliminating burrs, sharp pointed, tool marks and crusts of casting. They are used to clean metallic pieces, ceramics and polymeric materials. The process is based on rubbing or friction by abrasives. The pieces are arranged in the barrel with an abrasive and an additive (water or chemical additive). The machine produces a rotating movement on the pieces. When the abrasive passes against the surfaces of the pieces, it produces an action of rubbing and impact that cleans the surfaces. The rubbing action is developed when the upper layer of the charge slides to the lower extreme when the barrel rotates. The barrel can be hexagonal or octagonal to facilitate the sliding of the charge. The barrels can be between 15 to 120 cm in length and they can have almost any diameter and velocity of rotation. There are several types of barrel: individual, multiples, and multiple compartments. The barrels are rotated using a wheel spindle or rolling pins, that the can ride horizontally or be tilted to produce an additional movement of the charge.IntroductionShot penning is a cold method in which compressive effects are induced on an exposed surface of a metallic piece, by the impact of a rain of shots directly on the surface of the metal, at great speed under controlled conditions. This differs from cleaning with the help of air, because even when shot penning cleans the surface of the metal, this function is incidental. The main purpose of shot penning is to increase the resistance of the piece to fatigue. The process has other applications: raises the tensile strength and decrease corrosion fracture."

Jan 1, 2012

By Rachel De Lucas

In recent years, as the price of oil soars upward, scientists have started to focus on other energy sources, such as hydrogen. As magnesium can be used for hydrogen storage by forming MgH2, industry will see a growing demand for the hydride. In hydrogen storage and release cycles using magnesium, hydrogen is released from magnesium hydride through hydrolysis and magnesium hydroxide is produced. Therefore, recycling magnesium hydroxide back to magnesium becomes important. The solid oxide membrane (SOM) process is an emerging technology for this process. In the SOM process, MgF2-CaF2-MgO flux is contained in a stainless steel crucible, which works as the cathode. An ionic-conducting YSZ membrane, connected to a liquid metal anode, is partially immersed in the flux. During electrolysis, when the voltage between anode and cathode is higher than the dissociation potential of magnesium oxide, magnesium ions move toward the cathode and are reduced into magnesium vapor. The oxygen ions move toward the anode, passing through the YSZ membrane. They are then oxidized, forming pure oxygen, CO/CO2 or steam (by reaction with hydrogen). The magnesium vapor, generated at the cathode, is collected in the condenser as high purity magnesium. SOM experiments have been conducted with different liquid metal anodes and without reductants. The SOM technique is a highly energy efficient process and with by-products being oxygen or steam, it is also an environmentally friendly green process. A 2-D electrostatics mathematical model was developed as an initial step towards optimizing the design for a three-tube scale-up SOM electrolysis cell. Several possible geometries were examined to develop the scale-up model and convergence of the model was achieved.

Jan 1, 2006

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994