Search Documents

By G. Roderick Eggert

Material criticality reflects the degree to which a raw material is both necessary and subject to supply-chain risks. This study compares the criticality of selected raw materials from the differing perspectives of the manufacturing sectors of China, the European Union, Japan and the United States.

By Moenster J. A., M. J. Sankovitch

Doe Run's Buick Smelter was converted from a primary lead smelter to a secondary lead smelter in 1991. The recycling facility was designed to produce 60,000 tons of refined lead per year from 110,000 tons of spent starting-lighting-ignition (SLI) batteries and 10,000 tons of lead contained in drosses and scrap. Since commissioning, Buick's refined lead output has steadily increased to exceed 120,000 tons for 1999. The production gains have been the result of continuous process improvements, empowerment of the workforee, and development of additional scrap lead streams. The production gains were accomplished while setting industry standards for employee safety, reducing plant environmental emissions and employee blood leads, achieving ISO 9002 certification, and expanding product lines to meet customer requirements. This paper highlights Buick's major accomplishments through the 1990's.

Jan 1, 2000

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By Onuralp Yucel, Ahmet Turan, Halil Yildirim

"Nickel is mainly used in stainless steel production as ferronickel. In recent years, low grade ferronickel or nickel pig iron (NPI) is used in stainless steel production to reduce expenditure of nickel price. In this study, Turkey East Anatolian region lateritic nickel ores were directly introduced carbothermal reduction to produce NPI. Firstly the raw lateritic ore that contains 0.9% Ni, 0.054% Co and 2.3% Cr was mixed with metallurgical grade coal at different stiochometric ratios. The samples were smelted at 1600-1650 °C temperature range in an induction furnace for 25 min. In the second experimental set, different processes times were carried out from 15 to 35 min. The raw material, obtained alloys and slags were analyzed by using XRD (X-Ray Diffractometer), XRF (X-Ray Fluorescence Spectrometer), AAS (Atomic Absorption Spectrometer) and EPMA (Electron Probe Micro Analyzer) techniques.IntroductionNickel is an important element that has many application areas in the industry and there are a lot of kinds of nickel products such as refined metal, powder, sponge etc. 65% of metallic nickel is used in stainless steel, 12% is consumed as superalloy and non ferrous alloy because of its superior corrosion and high temperature properties [1].Nickel is a transition metal that is mined from mainly two types of ore deposits as sulphide ores and lateritic ores. Although 73% of nickel ores are laterites, 55% of primary production is from sulphide ores [1, 2]. The importance of lateritic ores is increasing due to the increase in nickel prices and decrease in reserves of sulphide ores.There are pyrometallurgical, hydrometallurgical and combined (pyro-hydrometallurgical) methods which are used for the extraction of nickel from lateritic ores. HPAL (High temperature pressure acid leaching) is generally used to recover nickel and cobalt from laterite nickel ores. It is suitable for the plants processing ores with low magnesium oxide and aluminum oxide content. Lateritic ores are exposed to hot acidic leaching around ~250 °C to dissolve cobalt and nickel under high pressure. The main disadvantage for HPAL is the high cost of titanium autoclaves. Process is complex and difficult to control due to the high pressure and heating of the process [2, 3 and 4]."

Jan 1, 2012

By Selvin Yesilay, Munevver Caki, Canbora Bayraktar, Bekir Karasu, Rahmi Imrak

"In this study, the utilization capability of the solid wastes taken from a commercial roof tile and brick factory in Eskisehir of Turkiye has been investigated in the production of stoneware bodies which can be formed by slip casting. At the first stage, X-ray fluorescent (XRF) and X-ray difractometer (XRD) analyses of the wastes were performed. Depending upon the results, a body recipe with an optimum casting concentration was adjusted. The bodies obtained from prepared slips were fired at 1160 oC as glazed and unglazed forms. Then, they were undergone certain tests in order to determine their firing shrinkage values, water absorption levels and optical parameters. To establish what kind of phase formations occurred after firing as a result of waste incorporations into bodies XRD analysis was conducted. Additionally, effects of such a compositional modification on the microstructure of the bodies were examined by a scanning electron microscope (SEM). Consequently, it was concluded that fired roof tile and brick wastes could be evaluated in both glazed and unglazed stoneware bodies. Introduction Stoneware is the general name applied to many wares fired between 1150 and 1300 °C. It has a different and denser structure than those of ceramics produced at lower temperatures. Fired stoneware possesses a lower water absorption value. When matured at a high temperature, it gives a possibility for the use of feldspar as a main ingredient [1-2]. Colors of stoneware can be brown, red, white and most of the times beige. Firing usually takes place in oxidation atmosphere but also reduction can be rarely used. This naturally has an effect on the body colors [3]. Earth, which contains clay minerals, becomes plastic mud when mixed with water, has a capability to be easily shaped and can be hardened without cracking if fired at 900-1000 °C, is referred as one of the brick and tile raw materials [4]. Natural and aesthetic appearances of buildings obtained with brick and tile products, which make them preferable especially for construction sector, are of importance. Because clays being main raw material of that type of productions generally do not exist as pure materials in nature, their usability depends on their mineralogy and impurities they contain [5]."

Jan 1, 2008

By Lin Yang, Minjun Tang, Shuishi Liu, Jianfeng Zhou, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"The dynamics of oolitic hematite magnetic roasting was studied. The results show that oolitic hematite magnetic roasting was controlled by the internal diffusion, and the diffusion coefficient was 9.018x10-7 m2·s-1when the oolitic hematite was roasted at 650°C. Magnetic susceptibility improves when temperature increases and roasted time prolonges under the condition of roasting at 650°Cfor 50min, with the magnetic susceptibility is 39.88%. CaF2 and Na2C03 can significantly improve the magnetic susceptibility at the same roasting condition, and the magnetic susceptibility was 63.35% and 57.99% respectively, thus the reduction of oolimic hematite was promoted.IntroductionWith the continual depletion of free-milling iron ores and its rising price, developing the abundant resources of oolitic hematite has become one of the main research areas. The oolitic hematite accounts for 10% of China's iron ore reserve, and it also accounts for 30% of red ore reserve in China [1]. In order to exploit the oolitic hematite, there are many beneficiation research methods, including fine grinding/selective flocculation/high intensity magnetic separation or flotation, high-gradient magnetic separation, low intensity magnetic separation/high intensity magnetic separation/reverse flotation, chloridizing roasting/acid pickling, magnetic roasting/leaching process etc [2]. However, the oolitic hematite is easy to slim and the valuable mineral is covered by the slim, because of the tiny granule of value mineral, then the ooides are formed due to the state of layer morphology formed by iron ore and ganaue minerals [3, 4]. Fairly good separation indexes were hard to be obtained by traditional separation due to its structural features, so the magnetic property of the iron minerals will be changed with the use of the magnetic roasting [5, 6], which result in hematite variably altered to magnetite and simplified technological process so that a good separation indexes will be obtained by using the low intensity magnetic separation. Therefore, in order to provide theoretical direction of how to use the oolitic hematite effectively through the magnetic roasting, the oolitic hematite of GuiZhou province was studied, which emphasized on researching the dynamics of oolitic hematite magnetic roasting."

Jan 1, 2013

By S. K. Varma, Miriam Regalado, Daniel Salas, Erica Corral, Erika Esquivel

"Age hardenable 2014 aluminum alloys and composites containing 0.10 and 0.15 volume fractions of alumina particles (VFAP) have been solutionized at 540 and 550°C for up to 20 hours. The solutionized samples, heat treated for 5 and 20 hours, have been subjected to room temperature rolling until cracking develops. The work hardening curves have been compared to determine the effect of solutionizing time on the rolling characteristics from both hardness and the microstructural evolution points of view. Solutionizing at two different temperatures results in differences in the extent to which the composites can be rolled until fracture. The microstructural characterization by TEM has been performed to understand the room temperature rolling behavior.IntroductionThe effect of solutionizing on the age hardening response of 6061 and 2014 aluminum alloys and composites reinforced with 0.10, 0.15 and 0.20 volume fractions of alumina particles (VFAP) have been reported in the literature [1-4]. A comparison of the monolith and composites indicates that particles promote the aging process through differences in the microstructures in solutionized condition. The first effect of solutionizing is to produce a grain growth process which follows a grain growth law (square of grain diameter as a function of solutionizing time). It appears that it is possible for vacancies to be emitted during grain growth period as they try to minimize the total grain boundary surface area by increasing their diameter. This may be common to both the monolith and the composites. However, the second effect must be exclusively considered for the composites. The particles generate dislocations during the solutionizing process due to the differences in the values of the coefficient of thermal expansion (CTE) between the particles and aluminum base metal. It has been determined [1] that the dislocation density increases with increase in solutionizing time in the composites of 6061 aluminum alloys reinforced with 0.10, 0.15 and 0.20 VFAP. The improved bonding between particles and matrix can give rise to additional generation of dislocations due to curvature effects [1] with the result that the dislocation density continues to increase with increase in solutionizing time even after the CTE effect is considered to have been stabilized."

Jan 1, 1998

By Laurentiu Nastac

"An advanced casting simulation-based optimization approach was applied in this study to assist in the improvement of the mold design of aerospace components made of A3 56 alloy. By using this approach, mold filling and solidification related defects (including macro-shrinkage and shrinkage porosity) were significantly minimized and hence it helped in cost reduction, performance enhancement and quality assurance of complex A3 56 cast parts.An experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and shrinkage porosities were performed using A3 5 6 plates cast in fiiran-silica sand molds using the Prometal's Rapid Casting Technology (RCT) - mold printing technology. Correlations between Niyama values and the pore percentage were also developed. Thus, the severity level of shrinkage porosity can be determined via the Niyama criterion. Predictions were then compared with the macro-shrinkage and porosity measurements in plates of various plate thicknesses and in other commercial A3 56 casting components.IntroductionThis paper describes the process modeling approach used in the development of the mold design technology used to produce assist in the improvement of the mold design of aerospace components made of A356 alloy. Nova Flow&Solid™ software [3] was applied in this study. This casting simulation software was previously validated for several alloys including Ti, steel and superalloys [1-4]. The objective of this paper is to calibrate and validate the simulation software for A356 alloy sand mold castings. For this purpose, an experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and microshrinkage (e.g., shrinkage porosities) were performed using A356 plates cast in fiiran-silica sand molds using the Prometal Rapid Casting Technology (RCT) mold printing technology. The details of the RCT technology are shown in Fig. 1 [5]. Prometal's RCT technology is used for rapid production of sand molds and cores directly from CAD files. The RCT technology relies upon ink jet printer technology to selectively bind the grains of sand to create three-dimensional sand molds and cores. Mold filling and solidification modeling as well as stress analysis are typically performed to properly design the casting and the rig system of each prototype component."

Jan 1, 2012

By Wankun Wang, Shixing Wang, Jinhui Peng, Zebiao Zhang

"Germanium leaching from germanium dust and fume was carried out using sulphuric acid. Response surface methodology (RSM), based on a five level, four variable central composite design (CCD), was employed to obtain the best possible combination of liquid/solid ratio (Xi: 2-10), leaching time (X2: 1-5 h), sulphuric acid concentration (X3:3.15-15.75mol/L) and leaching temperature (X4:50-90 *C) for germanium leaching. The obtained experimental data were fit to a one-order polynomial equation using multiple regression analysis and also analyzed by analysis of variance (ANOVA). The 3-D response surface plot and the contour plot derived from the mathematical models were applied to determine the optimal conditions. The optimum extraction conditions were: liquid/solid ratio of 10, leaching time of 1 h, sulphuric acid concentration of 15.75 mol/L, and leaching temperature of 87.8 'C. Under these conditions, the germanium leaching extent was 65.14%, which is in close agreement with the value predicted by the model. The samples were characterized before and after leaching using X-ray diffraction (XRD).IntroductionResponse surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [1-15]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the vital controllable factors are identified. It is also used to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected [6], The process optimization of the sulphuric acid leaching of germanium from germanium dust and fume has not been reported in the literature. Hence the present work intends to assess the effects of variables such as liquid/solid ratio, leaching time, sulphuric acid concentration and leaching temperature and to identify the optimum conditions using RSM. The characteristics of sample before and after leaching are assessed using the advanced analytical instruments such as X-ray diffraction (XRD)."

Jan 1, 2012

By Lucas L. Costa, Luiz F. Lopes, Ludy C. Motta, Felipe P. D. Lopes, Sergio N. Monteiro, Lara S. Vasconcellos

"Environmentally correct materials like the lignocellulosic natural fibers, which are renewable and biodegradable, are being extensively investigated as possible substitutes for synthetic fiber in polymeric composites. Several natural fibers have never been thoroughly investigated as possible composite reinforcement. The fiber obtained from the leaves of the buriti (Mauritia flexuosa) palm tree is one example. Therefore, the objective of this work was to study the properties of buriti waste fibers, in amounts of up to 30%, reinforcing polyester composites.IntroductionIn the past century, the technological development gave priority to new synthetic materials with energy intensive methods of production. Today, there is a concern that conventional energy source such as petroleum, natural gas and coal are the main responsible for global warming. Therefore, the use of natural materials is gaining attention not only for the saving in process energy but also the renewable and biodegradable characteristics that make them environmentally correct. The lignocellulosic natural fibers extracted from cultivated vegetables like jute, sisal, hemp, coconut, flax, ramie and many others are typical examples. This type of fiber is being extensively investigated as a possible substitute for synthetic ones, especially the glass fiber, as composite reinforcement [1].A relevant example of lignocellulosic fiber substitution is nowadays occurring in vehicles. The automobile industry is applying composites reinforced with natural fibers to replace parts such as panels and seat cushions made of fiberglass or polymeric foams [4], as illustrated in Fig. 1. The practical reasons for this preference are that natural fiber composites present less damage to tools and molding equipments as well as relatively better finishing and less abrasive surface than corresponding parts made, for instance, of glass fibers. On top of these advantages, low cost is probably the main motivation for the industrial interest for natural fiber composites, especially in the case of residual fibers [5] or post-used fabrics such as jute sackcloth [6]. Natural fibers, however, are hydrophilic and will not form strong bonding with a hydrophobic polymer, normally used as composite matrix [1-3]. Another disadvantage is the heterogeneous characteristics of a natural fiber, which is typical of biomaterials. This results in a relatively great dispersion of dimensions and properties values such as the mechanical strength [1-3]."

Jan 1, 2008

By Bradford C. Wesstrom, Omar Araujo

"Impurities from an electrolytic refinery are typically extracted from the electrolyte utilizing conventional electrowinning cells. These cells are arranged in series with cascading solution flow and are commonly referred to as liberator cells. The Freeport McMoRan Copper & Gold El Paso Refinery has optimized the removal of arsenic in cascading liberator cells by utilizing two separate feed solutions. The primary feed solution is recycled liberator electrolyte and the secondary feed solution is ""neat"" tank house electrolyte. The secondary feed solution is added based on the voltage response across the individual cells utilizing independent variable frequency drive (VFD) pumps. When the voltage across a cell changes, a signal is sent to the VFD pump to maintain a cell voltage of 1.98 volts. By maintaining this voltage the copper content in each cell exits at 2-4 grams per liter. This safely optimizes the arsenic removal as copper arsenides on the liberator cathodes.IntroductionDuring the electrolytic refining of copper, impurities from the copper anode report both to the bottom of the electrolytic refining cell as slimes and to the electrolyte. The impurities which enter the electrolyte are arsenic, antimony, bismuth and nickel. The impurities that report to the electrolyte during the electrolysis process gradually increase. As these impurities increase, they are incorporated into the refined copper cathode. There are many processes that have been used to remove these impurities from refinery electrolytes. Some of them are listed as follows: solvent extraction, ion exchange, hydrogen sulfide reduction, bioreactor, adsorption onto a low - solubility metal-oxide hydrate, adsorption onto activated carbon and EMEW cells. The conventional process used by the copper refining industry for controlling the level of impurities in electrolyte involves multistage electrolytic cascading liberator cells. In these cascading liberator cells copper, arsenic, antimony and bismuth are removed as various mixed deposits from the electrolyte. Removal of these impurities is achieved through an increase in voltage resulting from the depletion of copper in the electrolyte through electrowinning. With this higher voltage, the Group Vb elements, arsenic, antimony and bismuth are deposited on the copper cathode and report as slimes to the bottom of the cells. Nickel is removed in a subsequent process."

Jan 1, 2012

By Dmitri Goljandin, Jaan Kers, Xiangjun Zuo, Lifeng Zhang, Priidu Peetsalu

"In this paper, the mechanical milling of the electronic wastes was carried out. The metal parts and plastic parts were roughly separated. The final plastic powder size could be as small as ~100 µm. Then the pyrometallurgical recycling Printed Circuit Boards (PCB) was executed. The mechanisms of thermal degradation and combustion are investigated using TG/DTA and MS. Some chemical powders, such as Na2CO3, NaHCO3, NaOH and CaCO3 are used to control the exhausted toxic gas such as Br2. Introduction Waste electric and electronic equipment (WEEE), or electronic wastes (E-wastes), has been taken into consideration not only by the government but also by the public due to their hazardous material components [1-3]. From the point of material composition, electronic wastes can be defined as a mixture of various metals, particularly copper, aluminum, and steel, attached to, covered with, or mixed with various types of plastics and ceramics [4]. Precious metals have a wide application in the manufacture of electronic appliances, serving as contact materials due to their high chemical stability and their good conducting properties. Platinum group metals are used among other things in switching contacts (relays, switches) or as sensors to ascertain the electrical measurand as a function of the temperature [5]. Table 1 [6] gives examples of the metal composition of different electronic scraps from literatures. Additionally, non-ferrous metals and precious metals content have gradually decreased in concentration in scraps. The value distributions for different electronic scrap samples are shown in Table 2 [6], where the metal price data are from London Metal Exchange (LME) (Octoebr 2007). It can be seen that for cell phones, calculators, and printed circuit board scraps, the precious metals make up more than 70% of the value, for TV boards and the DVD player they still contribute to about 40%. This indicates that the major economic driver for recycling of electronic waste in industry is from the recovery of precious metals. Behind the precious metals come copper and zinc, while Al, Pb, and Fe are less value. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials."

Jan 1, 2008

By Antonio de Ita, Isaias Hilerio, Miguel Barron

"The influence of an unconventional lance with a central nozzle on the multiphase fluid flow in a steelmaking converter is studied in this work by means of computer simulations. The lance has four peripheral supersonic nozzles and a vertical central nozzle. Besides, the oxygen flow in the central nozzle is considered independent from the main oxygen supply. Transient two-dimensional numerical simulations were carried out considering just molten steel and gaseous oxygen as the existing phases. Numerical results show that bath agitation and droplet generation are enhanced as a result of the central nozzle. However, the performance of this lance strongly depends on the distance of the lance tip to the molten steel surface and the velocity of the oxygen jet.IntroductionCurrently, two thirds of the world crude steel is produced through the steelmaking oxygen converter [1]. Given the unquestionable economic importance of this technology, any improvement or optimization proposal is welcome. In the majority of current oxygen converters a top oxygen supersonic jet is blown onto the molten steel through a water-cooled lance to eliminate by oxidation some impurities such as carbon and phosphorus. Conventional lances have inclined peripheral nozzles whose number depends on the converter capacity. During the process, a large amount of gases evolves, forming metal droplets and a metal-slag-gas emulsion [2]. The droplets and the resultant emulsion increase the reaction interfacial area, promoting in this way carbon removal and dephosphorization of the molten steel bath [3]. However, during the blowing stage, the emulsion rises towards the lance and converter mouth and frequently forms layers which accumulate in the lance, reducing the life of the lance tip [4, 5]. It is possible that some freezing of the molten metal occurs due to the low oxygen injection temperature, however there are no reports on this. Besides, frequently undesirable operating phenomena such as spitting and slopping may arise as a result of inappropriate blowing practices or bad lance design. In the oxygen steelmaking industry, novel lances design are needed in order to enhance the decaburization rate and the slag formation and, at the same time, preventing operating practices that decrease productivity and move away the shop from safety standards."

Jan 1, 2012

By Matthias Schnitzler, Herbert Pfeifer, Ralf Bolling

"To transform metals high temperatures are usually needed. A fast and efficient heating can reduce the C02 emitted. The fastest way to heat metals is called direct flame impingement (DFI). The flame impinges upon the item being heated. For this method it is important to know the shape and length of the flame. Laser-induced fluorescence (LIF) technology allows measurements of a two-dimensional field without influencing the reaction or the flow. Commonly used is the measurement of OH-radicals, an indicator of the reaction zone.In the presented study measurements of a turbulent diffusion flame are shown. The position of the reaction zone and the influence of the distance between the item being heated and the burner are investigated. Conventional measurements and LIP-measurements are compared and the potential of DFI to increase the efficiency of heating metals is discussed.IntroductionDuring industrial heating processes a fast and efficient heating technology is required. Two important aspects are the NOx emission and the energy efficiency. The direct flame impingement (DFI) technology has the highest heat transfer rate possible with a gas/air flame. The turbulent high velocity flame jet impinges upon the item being is heated [ 1]. Due to the high heat transfer rate furnace and exhaust gas temperatures are lower. Therefore the energy efficiency is increased and the amount of NOx emitted is reduced.Hydroxyl- (OH-) radicals are an intermediate product that is generated during the combustion of hydrocarbons [2]. They are commonly considered as an indicator for the reaction zone and position of heat release. Figure 1 shows the hydroxyl-mole fraction in dependence of the distance along the gas flow. The figure clearly shows how fast the OH-concentration increases in the reaction zone. Figure 1 also shows that OH-radicals are present in the post combustion region, however in smaller concentration [3].The laser-induced fluorescence technology serves to measure the spatial distribution of OH-radicals in a two dimensional cross-section area of the flame. Therefore the flame dimensions and location can be determined with high spatial resolution without influencing the flow or the reaction [ 4,5]."

Jan 1, 2012

By Doon Gibbs

In this talk, we review highlights of x-ray magnetic scattering studies performed during the last decade, concentrating at the beginning on experiments on the rare earth metal holmium.(1-4) Besides intrinsic interest in the x-ray scattering cross-section and its description, studies of this type are motivated by the possibility that new structural and magnetic properties of rare earth metals might be revealed, and that new techniques may thereby be developed. As a result, interest in x-ray magnetic scattering experiments. has grown rapidly during the last 10 years particularly, with the regular application of synchrotron radiation techniques- Magnetic scattering experiments have by now been performed at most of the x-ray synchrotrons around the world. In addition, insertion .device beamlines dedicated to x-ray magnetic scattering experiments are planned at each of the next-generation storage rings presently under construction in the United States (APS), Europe (ESRF), and Japan (SPRING-8). Generally, the results of x-ray magnetic scattering experiments may be analyzed within two regimes of the incident x-ray energy, namely, in the limit of high x-ray energies, when the incident x-ray energy lies above the excitation energy of any absorption edge, and at resonance, when the incident energy lies near an absorption edge. In the high energy limit, the amplitude for x-ray magnetic scattering has the simple form [L(Q)?A + S(Q)?B](5-7) Here, L(Q) and S(Q) refer to the Fourier 'transforms of the atomic orbital and spin magnetization densities, respectively, and the vectors A and B depend on the incident and scattered wavevectors and on the: incident and scattered polarization vectors. 7) Because the vectors A and B are not identical, the polarization dependence of the orbital contribution to the magnetic cross-section differs from that of the spin contribution. This leads to the possibility that the orbital and spin magnetization densities maybe distinguished, in x-ray scattering experiments. The same distinction is not directly possible by neutron diffraction techniques (in dipole approximation, where the polarization dependence of the orbital contribution is identical to that of the spin contribution), and is important to a fundamental understanding of the electronic structure of magnetic materials. A particular

Jan 1, 1992

By Chris T. Vild

"ABSTRACT NOT AVAILABLEPRESENTATION SUMMARYIntroductionToday, light gauge aluminum scrap is melted in sidewell furnaces using natural gas reverberatory burners. The scrap is introduced into the sidewell adjacent to the combustion chamber through a submerged archway. Super-heated metal is then pumped into the sidewell where it aids in melting the scrap. From the sidewell, the flow is returned to the combustion chamber through a second submerged archway at some lower temperature. Normally, the burners are set at a designed high fire level and the scrap is introduced at a rate to attempt to mat.ch the burner input. A thermocouple in the bath is programmed to throttle back the burners to low fire if a high temperature limit is exceeded.Jn many cases the thermal efficiencies of these furnaces can be very low. With inadequate circulation, air and natural gas furnaces run at a dismal 18% thermal efficiency. If a circulation system· is added, the efficiency can jump to 28%. For a $100 million lb/yr recycling facility, and natural gas prices reaching $4.50 per million Btu, fuel cost at 18% efficiency can reach $1 million per year. A 10% increase in thermal efficiency saves $350,000 a year in fuel costs.With an increase in thermal efficiency, furnace utilization also increases. A 10% increase in thermal efficiency would result in a 20 million Btu furnace producing 12,000 lb/hr up from 8,000 lb/hr or 35 million lb more produced per year. This is a 33% increase in output.Most current furnace development has focused on burner technology using oxy-fuel, regenerative burners, etc. However, thermal efficiency is also largely effected by the molten metal circulation rate and how well the scrap is mixed into the superheated metal. Therefore, the flow dynamics should be optimized first, before installing of more thermal power.Jn an effort to understand the effect of these variables, a series of computer models were made and the critical factors studied with the goal of demonstrating an increase in thermal efficiency and production. Large-scale graphical representations of these models will be presented."

Jan 1, 2000

By Laurence G. Dyer, David G. Dixon, John Rumball, Maziar Eghbalnia, Edouard Asselin

"Linear scan voltarnmetry was used to determine the reactions that occur during the cyanidation of petzite (Ag3AuTe2). Gold oxidation in petzite requires more oxidising conditions than are required for pure gold, it also does not achieve the same current (related to reaction rate). Tellurium oxidation occurs at a similar potential in water and cyanide, but as a component of petzite is impeded somewhat in water, likely due to the stability of the precious metals. Pre-treatment of petzite to oxidise tellurium in the absence of cyanide prior to gold recovery appears to be at least moderately successful.IntroductionWhile gold occurs most prevalently in its native form, many other gold bearing phases appear throughout natural systems [I]. Tellurides are a common group of such minerals, many of which also contain silver, often existing in association with native gold deposits. The six major gold-bearing tellurides are calaverite (AuTe2), sylvanite [(Au, Ag)2Te4], montbrayite [(AuSb)zTe3], krennerite [(Au1-x, Ag,)Te2], petzite (Ag3AuTe2) and muthmannite (AuAgTe2) [2]. While several other phases exist they are much more complex (i .e. buckhornite), which dilutes and confuses the influence of each specific component. Studies of gold tellurides have predominantly focussed on calaverite as it is the simplest and most common phase, however petzite, commonly found in Australia and North America, is the focus of this investigation.Gold processing via cyanidation has been operated for more than a century and is a highly effective hydrometallurgical treatment of native gold deposits. However, some gold alloys such as tellurides have proven to be somewhat less responsive under the same conditions. Several groups have shown that gold/silver tellurides are amenable to cyanidation, but are significantly more refractory than native gold [3]. Pre-oxidation steps have been tested to remove constituents that would consume cyanide such as sulfides. Such species are also linked to the precipitation of oxidised telluriwn, forming a passive layer, further inhibiting gold recovery [2]. It is uncertain to the definite reasons underpinning the refractory nature of precious metal tellurides in conventional cyanidation."

Jan 1, 2012

By Jean Igor Margem, Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Noan Tonini SImonassi, Sérgio Neves Monteiro, Rômulo Leite Loiola

"Fibers of giant bamboo (Dendrocalmus Giganteus) are amongst the strongest lignocellulosic fibers. Although studies have been already performed, limited information exists on the mechanical properties of polymeric composites reinforced with continuous and aligned giant bamboo fibers. This work evaluates the tensile strength of this type of composite. Standard tensile specimens were fabricated with up to 30% of fibers aligned along the specimen's length. The fibers were press molded with a commercial epoxy resin mixed with a hardener and cured for 24 hours at room temperature. The specimens were tested in an Instron machine and the fracture surface analyzed by scanning electron microscopy. The tensile strength increased significantly with the amount of giant bamboo fiber reinforcing the composite. This performance can be associated with the difficult of rupture imposed by the fibers as well as with the type of cracks resulting from the bamboo fiber/epoxy matrix interaction, which prevents rupture to occur.IntroductionDue to growing concern about the ambient impacts from industrial activities, our society is ever more using environmentally friendly materials. In this regard, cellulose-based natural fibers, known as lignocellulosic fibers, become a promising solution. Nowadays, they are being considered as a substitute for synthetic fibers, such as glass fiber, used by the industry on a large scale [1-5]. The application of these natural fibers is also motivated by many advantages like good toughness and less wear of equipment used in the processing of composites. In addition, such composites are environmentally friendly because they are renewable, biodegradable and neutral with respect to C02 emissions, the main responsible for global warming and climate changes. [3,5,6].Lignocellulosic fibers also have some disadvantages in relation to synthetic fibers such as the difficulty of coupling with polymer matrices, due to the hydrophilic character of fiber and the hydrophobic nature of the matrix, as well as dimensional heterogeneity [ 4,5]. This last one is characteristic of the nature of this material and constitutes an obstacle to the use of these fibers in certain projects, especially those that aim high performance. The above mentioned disadvantages are worrisome reasons for the occurrence of reduction in the strengthening capacity, as indicated by the rule of mixtures for composites [7]."

Jan 1, 2013

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"One of the methods for waste treatment is composting during which as a result of controlled biological decomposition of organic waste in aerobic conditions harmless materials are received. Composting takes place in suitably designed premises which ensure the optimal conditions for biochemical decomposition of the waste. A usual way to process composting is the spreading of the waste on a base made from reinforced concrete.In the paper the phases and basic technical features of the process of composting, the requirements and properties of the base and the ways of protection of concrete base against corrosion are revealed. Technical decisions for a specific construction site in Bulgaria are shown and the advantage of achieving durability of the concrete constructions in the plant while achieving simultaneous environment protection from pollution is discussed.IntroductionComposting is the process of controlled biochemical decomposition of vegetable and animal organic waste in aerobic conditions as a result of which harmless materials are obtained. The latter have better stability and are rich in humus substances which are useful for agricultural crops and can be used for restoring the soil fertility [1, 2, 3, 4].In modern waste treatment plants a composting technology is adopted in which the waste is spread on a concrete base as piles with certain dimensions [1, 3]. These piles are periodically stirred or air is blown through them in order to ensure the quantity of oxygen required for the process of aerobic decomposition of the organic matter. The fluids and gases formed in the course of the composting are take away in order not to pollute the environment – air, water, and soils. For this purpose the base on which the waste is spread must satisfy certain requirements, and the gases must be taken away and rendered harmless in order to protect the atmospheric air from pollution. This paper discusses the need for protecting the concrete base from corrosion and characterizes the stages and main parameters of the composting process and the possibilities for primary and secondary protection of the concrete base from corrosion. Specific technical decisions applied in a composting facility in the area of the town of Plovdiv are presented."

Jan 1, 2008