Search Documents

By H. -P. Behrendt

Muldenhiütten Recycling und Umwelttechnik GmbH is a lead smelter with a very long tradition. The first reference to the existence of smelters on this site is given by a document of inheritance dated 1318. Originally run as a primary lead smelter, which was supplied with ores from the Freiberg mining district and from overseas, it was required to change it over to secondary raw materials due the abandonment of mining in the Freiberg area in 1968. Today, Muldenhüitten Recycling und Umwelttechnik GmbH has two production lines; lead production from secondary lead and waste incineration, which are closely connected and gain advantage from each other. Installations, improved technologies, and the highly skilled personnel have contributed to satisfy all demands for a production concerning quality and environment.

Jan 1, 2000

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

"Recycling of solid wastes plays an important role in environmental protection. However, solid wastes are often contaminated with some undesired components so that many of these solid wastes are hardly economically recycled. Therefore, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes. There exist three general strategies of separation of undesired components from solid wastes: before-process separation, post-process separation and in-process separation. In this paper, different separation strategies are discussed in terms of energy requirement and availability, implementation complexity and additional need for environmental protection. It is concluded that of all separation strategies, in-process separation has the least energy requirement, the least implementation complexity and the minimum need for additional environmental protection.IntroductionIn industries, solid wastes almost come with every production process. Multi-million tons, if not billion tons, of solid wastes are being generated globally each year. These solid wastes are lowvalue materials in general, and often have very limited markets. As a matter of fact, many of these solid wastes have been stored on site or have been disposed of at landfills for many years, not only occupying lands, but also polluting environment. Therefore, effective and efficient recycling of solid wastes has been a very challengeable task and has played a very important role in environmental protection.One of the major barriers which hinder recycling of solid wastes is contamination of the solid wastes with some undesired components. These undesired components are components which are not wanted by production processes or applications where the solid wastes are consumed or recycled, since the undesired components often degrade qualities of the solid wastes, imposing negative effects on operations, facilities and product qualities of the production processes or applications. Sometimes, the undesired components may also pose severe environmental concerns. When undesired components are present in solid wastes at over-limit levels, the solid wastes tum to become destructive, useless and non-recyclable. Consequently, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes."

Jan 1, 2014

By Christian Bernhard, Mario Hartl, Susanne K. Michelic

"One aspect of an efficient process and product optimization of the liquid steelmaking process is the understanding of reactions and interactions between the components steel, slag and nonmetallic inclusions. The present paper focuses on a fundamental study of this topic by combining the powerful methods of thermodynamic modeling with systematic experiments on a laboratory scale and subsequent SEM/EDS analyses. The modeling aspect is addressed by the commercial software FactSage 6.1; laboratory experiments are performed for a low-alloyed, Ca-treated carbon steel combined with varying slag compositions. The consequent SEM/EDS analyses provide a detailed insight into the inclusion landscape which offers a strong tool for characterizing the modification of inclusions. In the present study the combination of these methods is mainly applied to oxides, due to their crucial influence on the final product quality, thus giving important indications for further optimizing the secondary metallurgy processes.IntroductionIn recent years, the range of application for steels has been enlarged continuously; also resulting in extreme surrounding conditions combined with considerable stresses for the material. This trend is directly linked with higher demands on the properties of steels. In order to optimize the final product quality, the cleanness of steels is an important criterion. For this reason, the broad topic ""Steel Cleanness"" has become one of the main research points at the Chair of Metallurgy. Next to the continuous optimization of methods for the characterization of cleanness, the primary aim is to combine thermodynamic modeling and laboratory experiments in order to describe the changes in inclusion landscape under different conditions.The steel cleanness can particularly be influenced in the processes of secondary metallurgy. In different processes the reactions and interactions between the components steel, slag and nonmetallic inclusions (NMI) are essential for the final inclusion landscape. Consequently, the understanding of the occurring reactions is a fundamental aspect for further development and process optimization. In secondary metallurgy especially oxide-slag systems consisting of the components Ca0-Ah03-Mg0-Si02, which significantly influence the modification of NMI, are of importance. Several works dealing with the interactions of oxide non-metallic inclusions with different slag systems have been published in the last years [1-4]. In order to observe the dissolution of oxides in different slag compositions a Laser Scanning Electron Microscope is frequently used. A very detailed study on the ternary system Ah03-Ca0-Mg0 and its subsystems was also done by De Aza et al. [5, 6]."

Jan 1, 2011

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Shoji Taniguchi, Lifeng Zhang, Kaike Cai

"In the present paper, based on the two-phase (Eulerian-Eulerian) model, the 3D fluid flows in gas-stirred systems, i.e., air-stirred water vessel and argon-stirred liquid steel ladle, are simulated. In the Eulerian-Eulerian two-phase model, gas and liquid are considered to be two different continuous fields. The phases are assumed to share space in proportion to their volume fractions. The exchange between the phases is represented by source terms in conversation equations. Turbulence simulated by the k- e model is assumed to be the property of the liquid phase. The following effects of mathematical treatments and operational factors on the fluid flow are discussed, such as interphase drag force, turbulent model, the size of bubble, and gas injection mode.Some interesting results are derived. Except the interphase drag force, the interphase lift force should be taken into accounted in order to exactly simulate the fluid flow in gas-stirred systems. Suitable turbulent model and drag coefficient have effect on the mathematical simulation. Injecting small bubbles can realize a well mixing flow condition. The distance between the two gas-injection nozzles has effect on the fluid flow."

Jan 1, 2000

By J. W. Perez

In the treatment of process effluents containing metal ions, it is sometimes desired to remove all of the heave metal ions while at other time it is, desired to remove one heavy metal ion from another, selectively. Ion and precipitate flotation processes were evaluated to perform these functions using the copper-iron aqueous system as a model. Because preliminary foam fractionation experiments proved to be relatively inefficient, most of this work has focused on precipitate flotation using both hydroxide and sulfide precipitation. Test results indicate that by proper control of reagents and operating conditions, it is possible to substantially reduce the froth volume over that achieved with foam fractionation and to separate copper from iron selectively. Mechanisms for collector attachment to precipitates were studied.

Jan 1, 1992

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By Peter A. Spencer

Bacterial oxidation technology has the ability to selectively attack sulphide minerals. Selectivity allows oxidation of more reactive minerals and the extraction of valuable metals while leaving the bulk of the sulphide component unreacted. Partial oxidation can be used on arsenopyrite to recover gold and for the leaching of base metals, such as copper and nickel, from pyritic ore and concentrate without generation of large quantities of acidic iron solution, which must be neutralized. Thus, rejection of pyrite during the oxidation process can considerably reduce treatment costs. Acid generation in tailings dams would be minimal, compared with most Thiobacillus cultures, as the optimum growth temperature of Bactechts culture is above ambient.

Jan 1, 1992

By Jun Li

Rate processes of silver cyanidation were studied with the objective of understanding the reaction mechanism. The research was divided into three sections: anodic dissolution of silver in cyanide solutions, cathodic reduction of oxygen on silver surfaces and the direct leaching of silver in oxygenated cyanide solutions. The charge transfer steps plus the diffusion of reactants from bulk solutions to the silver surface were identified as rate-limiting and the rates of both anodic and cathodic reactions can be calculated using the Butler-Volmer equation and Fick's first law. Based on mixed potential theory and the results of electrochemical studies, a comparison of the rate obtained from direct leaching with that predicted from the calculation is made. Calculated results agree well with the experimental data.

Jan 1, 1992

By David N. Hanlon

The effect of high-temperature plastic deformation of the austenitic phase (y) on the subsequent phase transformation to ferrite (a) has been experimentally investigated, and modelled using a physically-based model. The effect is of importance for steel sheet, in view of me significance of the phase transformation with respect to the eventual properties of the material. In this paper the kinetics of the y ? a phase transformation has been studied after different degrees of prior deformation. The degree of deformation is varied by applying different deformation temperatures and strain rates, and by allowing a varying extent of recovery and recrystallisation. Consequently, both dynamic and static recovery and recrystallisation have been involved. The dilatometric observations on the phase transformation have been modelled using an interface-mobility model, in which the effect of the dislocation structure is introduced as an additional driving-force term. The effect of the stored energy on the nucleation process, which appears to be affected more strongly than the growth of ferrite, is examined in terms of the classical nucleation theory.

Jan 1, 2001

By Mao Chen, Tim Evans, Zhixing Zhao, Weidong Zhang, Baojun Zhao, Dongqing Wang

High temperature softening behaviours of iron blast furnace feeds (sinter, lump and pellet) have been determined under conditions simulated to the blast furnace. The industrial samples were packed with sandwich structure (coke / ore / coke) in graphite crucibles and 30 CO / 70 Ar gas mixture was blowing directly through the bottom of the crucibles. The displacement and temperature were continuously recorded simultaneously to construct the softening curves. Separated quenching experiments were also carried out at selected temperatures under the same gas atmosphere. The temperatures were selected corresponding to the turning points of the softening curves. The phase assemblages and composition of each phase in quenched samples were analysed by Electron Probe X-ray Microanalysis (EPMA). The proportion of the liquid formed at temperature was obtained from the backscattered electron images. The deformation characteristics of these complex multi-phase materials are shown to be related directly to the phase assemblages of the samples and the microstructures. FactSage was also used to assist the predictions of liquid / solid fractions and their compositions.

Jan 1, 2015

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By Martin Fischer

A new method for the quantitative image analysis of complex microstructures in steel is presented. Microstructures in modern steel grades on the one hand become more and more complex while on the other hand the size of the constituents is scaled down ever further. For these reasons it is increasingly difficult or even impossible to access reliable quantitative information on ratios, shapes and spatial distributions of individual phases and constituents by utilising traditional metallographic analysis methods. The presented new analysis approach is object-based. Its basic processing units are so-called ?image objects? which reflect the pictured structures by merged groups of likely related pixels. By the use of image objects, information on shape, graphical texture and spatial distribution of the microstructural constituents can be processed. With these additional data available, it is possible to quantitatively analyse complex microstructures. This is demonstrated by the application of the method to SEM images of different multiphase steel grades. Because the analysis routine is fully automated, the analysis of large amounts of image data is possible and thereby the investigation of statistically relevant areas of microstructures.

Jan 1, 2009

By Ronald J. McGregor

An overview or precious metals project development and start-up, which emphasizes the process decision. Logic which determines process flowsheet, project economics, and training required to train new operators for start-up. The process decision required to successfully develop a precious metals project requires a blending of test data, environmental considerations and operations experience. Decisions to use Merrill-Crowe or carbon adsorption/ electrowinning/replating, fixed pad or multi-use pad {in heap leach) are dependent not only on technology but also on ability to train new operators. The market for experienced operators is acutely depleted and almost all new operators will have to be "home grown". Experience from the Brewer project in South Carolina as well as other projects put together in the West will be discussed.

Jan 1, 1989

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By Tam Tran

Most new gold mines in Australia are required to treat tailings to reduce cyanide levels before they are discharged to storage ponds to meet the stringent environmental management guidelines set by government statutory authorities. In New South Wales, the average level of weak acid dissociable cyanide allowed in open tailings dams is now limited to 20 ppm, As stringent environmental guidelines continue to be enforced in Australia as well as in other parts of the world, the management of cyanide wastes has emerged as a key issue for the gold mining industry. This paper provides a critical evaluation on technical aspects related to the use of ion exchange resins and affiliated processes in cyanide management and tailing treatment. Particular attention is given to the use of ion exchange resin technologies in the processing of mixed gold-copper ores, where cyanide usage is the highest. Information presented in this paper is heavily drawn from the experience on the application of ion exchange resin processes at May Day mine, in New South Wales, Australia and associated pilot plant test programs. Issues related to the management of thiocyanate, especially with respect to the recovery of cyanide from thiocyanate are also discussed.

Jan 1, 1998

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994