Search Documents

By A. D. Besser

The world production of lead has been growing continuously and reached over 7 million tonnes in 2005. At the same time, the structure of lead consumption has changed: the use of lead compounds to liquid fuel has been virtually terminated; the proportion of lead for manufacture of lead-acid batteries has been growing and reached 76.7% of the overall world production of this metal. This has taken place against the background of increasingly stringent environmental norms and environmental legislation. This is due to the lack of an alternative for lead in manufacture of local power sources. A solution to the problem of meeting the industrial demand for lead with simultaneous reduction in the primary lead production is in recycling. A large amount of batteries manufactured worldwide and their short life cycle, as well as the positive economics and a possibility to comply with the environmental requirements encourage the development of secondary lead production. Currently, over 60% of the world demand for lead is met due to recycling. The current situation with collection, transportation, storage and processing of spent lead-acid batteries has been analyzed in this paper. Examples are given to illustrate technological and equipment solutions and trends for improvement of secondary lead production discussed.

Jan 1, 2006

By Robert W. Bartlett

Hazardous metal contaminants in liquid and solid wastes and from ground spills are important environmental problems in many metallurgical production operations. Acid rock drainage, from mines and huge quantities of permeable mine waste, is probably the most ubiquitous example. Fixing mine waste contaminants in situ has been practiced, using sulfate reducing bacteria (SRB) and organic reagents as electron donors to create anaerobic conditions and precipitate metal sulfides. Aqueous solutions of sugar and alcohol have been percolated into mine wastes with good results. However, maintaining anaerobic conditions permanently is unlikely, as these solutions are eventually washed out of solid waste and contaminated ground by inflow of either groundwater or meteoric water, allowing re-oxidation from entering air. Emulsions of inexpensive, non-aqueous organic microdroplets dispersed in water provide earth wettablility equal to aqueous solutions and easy percolation into both the ground and mine waste. Subsequent breakdown of the O/W emulsion provides permanent retention of the organic phase, attached to earth particles, that secures lasting anaerobic conditions, precipitates metals as sulfides and prevents re-oxidation of these sulfides. This process and its optimization are described, including experiments with sand-filled columns representing a vertical section through solid waste. Results of organic and metal retention in solid waste are provided from analyses of acid mine water drainage before and after waste treatment.

Jan 1, 2006

By D. Tahija

The Getchell Mine produces gold from a geologically complex ore bearing high concentrations of arsenic and carbonate minerals. The mill treats the ore using high temperature aqueous oxidation in autoclaves, followed by conventional carbon-in-leach gold recovery. We laboratory tested a variety of Getchell ores to determine the effects on gold recovery of conventional factors such as grind size and retention time, as well as the influence of factors such as ore variability and preliminary carbonate destruction. Because the mill is currently operating, we were able to directly compare certain laboratory predictions with operational results.

Jan 1, 1999

By Abhishek Lahiri

Titanium dioxide is extracted from titaniferous ores by chloride and sulfate processes. These two processes produce wastes in the forms of iron chloride, iron sulfate and rare earth oxides gangue, each of which has to go through a further treatment before it can be disposed safely, which may be expensive. The shortage of high-grade ores is also making the two conventional processes less efficient. In view of the above mentioned problems, an alternate beneficiation process of roasting titaniferous ores with soda ash is discussed. The advantage of this process is that, there is no production of wastes. The impurities present in the ore can be selectively separated after the roasting process. The roasting of titaniferous ores with soda ash was carried out between temperatures of 873K and1173K for several hours. The roasting process resulted in the formation of complex alkali compounds and various sodium titanate compounds, depending on the Na2CO3to ore ratio. The phases formed after roasting were characterized using the X-ray powder diffraction (XRD), X-ray florescence (XRF) and scanning electron microscopy (SEM) techniques. The phase equilibria in the Na-Ti-O system are evaluated and compared with the phases obtained after the roasting process. The effects of temperature and the proportion of sodium carbonate on titaniferous ores are also discussed. From the experimental data, the overall reaction kinetics and phases formed were analyzed to ascertain the mechanism of overall reaction and the rate-limiting steps.

Jan 1, 2006

By D. J. Sellmyer

This paper is Intended to review recent developments in the application of rare earth-transition metal alloys as high density, rewritable data-storage media. First generation magneto-optic media are based on amorphous Tb-FeCo or GdTb-Fe alloys which are adequate but could use improvements In certain respects. A very difficult materials-design problem is encountered because of the following requirements: a sufficiently large Intrinsic uniaxial anisotropy, a Curie temperature in the range 100-300°C, a sufficiently high coercivity, a sufficiently high optical absorption, a high Kerr rotation, reflectivity and high carrier-to-noise ratio, a high storage density, a very fine and homogeneous nanostructure, long-term stability, and inexpensive production. , Fundamental issues such as the relationships between the nanostructure and perpendicular magnetic anisotropy, and electronic structure and Kerr rotation are discussed. Attempts to tailor the properties by rare-earth alloying and by preparing compositionally-modulated, nanostructured multilayers are outlined. Challenges and opportunities in competitive materials such as garnets, ferrites and Co/Pt multilayers are briefly discussed.

Jan 1, 1992

Due to problems with old technologies more and more product designers have turned to liquid crystal (LC) displays, which have consequently experienced phenomenal growth. The success of liquid crystal displays has fostered continued development, to the point where full-color video displays have been realized which can rival. The details of the lens structure and of the devices fabrication and performance are described using the Jones matrix method. Director n can change from point to point and is, in general, a function of space.. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence. Light from the conventional light source or laser is passed through a polarizer and then incident on the specimen. The resist profile simulation is carried out using the combined data thus obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. At the nematic-isotropic, transition temperature, the medium becomes isotropic and looks clear and transparent.

Jan 1, 2006

By G. S. Nus

Technology for treating man-made metal-containing raw materials in DC electric furnaces with polarization of the bottom phase (PDF furnaces) has been developed and proven on a semi-commercial scale. PDF furnaces permit processing of man-made raw materials, i.e. current and accumulated intermediate products with rather high contents of valuable metals (i.e. slags, sludge, residues, Waelz slag, etc.), as well as secondary raw materials and virtually any type of waste using an environmentally safe technique based on sublimation of volatile metals and transfer of non-volatile metals and sulfur into the bottom phase in the furnace. Processes developed on the basis of the use of PDF furnaces make it possible to take advantage on a full commercial scale of electrolysis of molten materials, including electrochemical reduction of metals, intensification of their settling into the bottom phase and sublimation of volatile components, as well as to significantly improve recoveries of nonferrous metals, resolve the problem of excessive accretion formation in slagging processes and substantially improve the environmental situation. The low-grade discard slag obtained can be utilized in the construction industry; in particular, slag can be added to the limestone feed for cement manufacture.

Jan 1, 2006

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By Bruce W. Downing

MagPower has developed methods to control the detrimental formation of hydrogen that occurs in electrochemical reactions in numerous commercial applications such as the Magnesium-Air Fuel Cell, electrowinning, zinc alkaline batteries, hydrogen embrittlement, waste water/ metal recycling and coolants. The company?s approach to an alternative energy source is the development of an environmentally friendly non-toxic alternative power source that generates electricity through a combination of magnesium, oxygen and a saltwater electrolyte with MagPower?s patent pending hydrogen inhibitors. The magnesium-air technology has never reached the commercial stage due to its limiting power output caused by hydrogen generation. MagPowerhas solved this problem and has patents pending on its intellectual property; the Hydrogen Inhibitors and has developed several consumer power units for a variety of applications through licensing agreements. The company has also shown that the inhibitors have an impact on zinc electrowinning through laboratory test work where current efficiency was improved. This will significantly reduce power consumption and increase the efficiency of the electrowinning process, as well as reduce the potential acid mist hazards associated with electrowinning.

Jan 1, 2003

By Giuseppe Bonifazi

Minerographic and petrochemical research was carried out on crude ore samples from the complex polymetallic Zn-Cu-Pb sulfide ores of , Sotiel in Huelva province west of Seville, Spain. A computerized image analysis system was used to define the structural and textural characteristics of the ore to obtain information on the degree of liberation of the different minerals (i.e. pyrite, sphalerite, galena, chalcopyrite). Techniques of digital multispectral image processing of reflected light microscopy images were used. Particular structures were identified by means of mineral associations and numerically quantified to obtain useful information for designing beneficiation processes.

Jan 1, 1991

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By M. Omneya El-Hussaini, M. Galal Abdel Wahab, A. Mohamed Mahdy, M. Fathi El Shahat

"Lead-zinc mineralization is distributed in Egypt along the Red Sea coast between El Qusier and Ras Banas. A representative sample from Um Gheig was collected and ground to -60 mesh for the mineralogical study. It contains hemimorphite (Zn2SiO4.H2O), sphalerite (ZnS), galena (PbS), calcite (CaCO3) and dolomite (CaMg(CO3)2) beside the gangue minerals gypsum (CaSO4.2H2O) and hematite (Fe2O3). Cadmium seems to be incorporated in the crystal structure of the zinc-lead minerals. The chemical analysis of Um-Gheig representative sample revealed that, it contains 16% zinc combined with 0.1% cadmium, 2.3% lead and 0.1% boron beside other elements.Pug and agitation leaching were performed on samples ground to -200 mesh to achieve the maximum dissolution efficiency of cadmium with respect to other elements. Cadmium leaching efficiency reached 90% by using 40% H2SO4 at S/L ratio 1/2 and stirring time 2 hours at 80o C. Cadmium was then separated as yellow precipitate of CdS from the sulfate leach liquor containing 0.9 g/l Cd, 145 g/l Zn, 0.15 g/l B and 0.01 g/l Pb. Separation of cadmium was carried out by direct precipitation using Na2S as well as H2S. The recovery of 94% cadmium free of zinc was achieved.IntroductionLead-zinc ores occur in Egypt in a few localities distributed along the Red Sea coast between El Qusier and Ras Banas. Um-Gheig Pb-Zn ore is a replacement deposit in limestone and calcareous sandstone in the basal series of the Middle Miocene rocks. The reserve of the ore deposits has been estimated by Soviet and German Experts to be about 900,000 Ton, Bishai [1]. As has been mentioned, zinc is a common element and cadmium is comparatively rare in almost zinc minerals. It was estimated that zinc is 200 times as abundant as cadmium. According to Bodas [2] about 2.1% of cadmium was carried by the Zn mineral hemimorphite (15.3% Zn) in Thailand. Also, Onal et al., [3] found that 164 g/t Cd was carried by Pb–Zn ore sample containing 10.17% Pb and 10.98% Zn from Aladag in Turkey. Cadmium metal has gained great importance due to its wide applications in civil and navy purposes as well as in nuclear field. It is characterized by its ability to absorb thermal neutrons during the chain reaction inside the nuclear reactors. It is also used in the manufacture of sheets which directed the chain reactions [4]."

Jan 1, 2008

By Ashish D. Patel, Ramesh S. Minisandram

"Vacuum Arc Remelting (VAR) is the final and, hence, critical melting step for the production of a sound, segregation-free ingot for the manufacture of alloys used in rotating components in aircraft engines. A mathematical model for this process has been developed by the Specialty Metal Processing Consortium (SMPC). The model predicts temperature distribution in the solidifying ingot, flow in the molten metal pool, and the electromagnetic field in the ingot. These predictions may be used to estimate the effect of melting parameters on the pool profile in the ingot. In this paper, typical pool shapes and flow fields during VAR of Alloy 718 and Ti-6Al-4V are presented. The differences in the pool profile are primarily due to vastly different melting conditions. The model predictions are compared to the observed pool shapes from industrial-size VAR ingots.1. IntroductionVacuum Arc Remelting (VAR) is a process in which an electrode is melted in vacuum by the heat from a DC electric arc. Metal droplets from the electrode fall into the molten metal pool, which solidifies in a water-cooled copper crucible to form the ingot, as shown in Figure I. The ingot obtained from VAR is sound, and has superior cleanliness and chemical homogeneity. Hence, the process is the final melting process for most nickel-base superalloys and titanium alloys used in the manufacture of critical rotating components (discs & blades) of aircraft engines. Modeling of this process provides an insight into the effect of melting parameters on the molten metal pool in the solidifying ingot, which is a key first step in process optimization and defect prevention. In this paper, typical pool shapes, both measured and predicted, for VAR of Alloy 718 and Ti-6Al-4Vare presented. Alloy 718 is the most common VAR-processed nickel-base superalloy; whereas Ti-6Al-4V is the ''workhorse"" alloy for titanium-based alloys."

Jan 1, 2004

By Aichun Dou

Au-Sb alloy sample in which the total amount of Cu and Ni is below 25% (wt. %). In practice, Cu and Ni were difficult to be dissolved in sulphuric acid solution by oxidative leaching under the atmospheric pressure conditions, because of the lower concentration of Cu and Ni in the sample. In this paper, pressure oxidation leaching in sulphuric acid system (POLS) followed by hydrochloric acid leaching (HAL) was employed to remove impurities in the Au-Sb alloy. The effects of variables in POLS on leaching ratios of different metals were investigated in detail. Under the optimal conditions: the concentration of H2SO4 is 1.5 mol/L, liquid-solid ratio is 7:1, the amount of oxidizer is 1.2 times of the theoretical amount, leaching time is 4h and leaching temperature is 427K, the leaching ratios of copper and nickel reached up to 99%, antimony, lead and silver were not dissolved in dilute sulphuric acid solution. The residue from POLS was then treated with hydrochloric acid solution in fixed conditions, the leaching ratio of antimony reached over 92%, the grade of gold in the ultima residue was enriched up to 66%.

Jan 1, 2016

By L. M. Bianchi

"Oxide, nitride and other compound coatings often do not have adequate properties for newer applications when produced using very high deposition rates and simple evaporation techniques. Solar control, abrasion resistance, low reflectance and barrier effective engineered coatings require exacting properties. Such properties can be obtained by adapting the activated reactive evaporation (ARE) technology to Web production processes. Adaptions of the HAD and MAD processes will be described along with data on the high deposition rates obtained. These fast production capabilities were developed in order to make the processes economically competitive.IntroductionThe Physical Vapor Deposition technique (PVD) has been used to coat steel strip for over 20 years. (1) However, its use as a production process has been very limited because of the high cost of the PVD coating process and because, in some instances, the properties of the coating were not good enough to meet the customers requirements. Nevertheless, the PVD process has found wide application in the airplane engine and electronic component markets. These production processes have stimulated further development and advances in the technology.In 1971, Profession R. F. Bunshah developed the Activated Reactive Evaporation (ARE) process which was then used to produce hard coatings such as carbides, nitrides, oxides and other refractory compounds. (2) The process from a fundamental viewpoint -produces a coating on the substrate via the evaporation of metal in the presence of a low pressure (typically around 1 millitorr) of reactive gas, with a plasma created in the space between the metal source and the substrate.The plasma may be created by many means but its function is two-fold. First, it activates the reaction between the metal vapors and the reactive gas atoms/molecules resulting in the formation of a compound that deposits on the substrate. Second, because the plasma is in contact with the substrate, it results in a negative bias on the substrate and produces bombardment of the growing film with ions and energetic neutrals from the plasma. This bombardment causes many significant changes in the microstructure, properties and appearance of the coating.Recently another new technology Pulsed Magnetron Systems (PMS) has been introduced into PVD. This new technology has been pioneered in production scale equipment by Dr. S. Schiller (3) and associates. The use of a pulsed power supply on the magnetron prevents the problem of the anode being coated with a insulating layer which will then lead to micro and macro arcing producing defects in the coating."

Jan 1, 1998

By Donald R. Sadoway

The viability of treating certain forms of hazardous waste by direct electrolysis in molten oxides is under investigation. Secondary residue or waste mud produced in the course of chromate chemical production is the focus of attention in this study. The goal is to reduce the water soluble hexavalent chromium either to insoluble trivalent chromium or to chromium metal. Electrolysis tests have been conducted in a high temperature cell containing chromate sludge dissolved in an electrolyte composed of Al2O3, SiO2, CaO, and MgO. Oxygen production on a carbon-free anode has been confirmed.

Jan 1, 1992

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Cadmium and tellurium dissolution was achieved using hydrogen peroxide in dilute sulfuric acid. Leaching the scrap in 2.2 N H2SO4 yielded 99% Cd extraction and 98% Te extraction. Sulfur remained in the leach residue primarily in the elemental form. Elemental tellurium was precipitated from the leach liquor by adding Na2S2O5. Cadmium sulfate was recovered by evaporation. A preliminary process evaluation suggests that the process may have economic potential. Alternative recovery schemes are discussed.

Jan 1, 1995

By Virgil Optasanu, Yvon Lacroute, Eric Lesniewska, Tony Montessin, Pauline Vitry, Eric Bourillot, Cédric Plassard

A general challenge in metallic components is the need for materials research to improve the service lifetime of the structural tanks or tubes subjected to harsh environments or the storage medium for the products. One major problem is the formation of lightest chemical elements bubbles or different chemical association, which can have a significant impact on the mechanical properties and structural stability of materials. The high migration mobility of these light chemical elements in solids presents a challenge for experimental characterization. Here, we present work relating to an original non-destructive, with high spatial resolution, tomographic technique based on Scanning Microwave Microscopy (SMM), which is used to visualize in-depth chemical composition of solid solution of a light chemical element in a metal. The experiments showed the capacity of SMM to detect volume. Measurements realized at different frequencies give access to a tomographic study of the sample.

Jan 1, 2015

By R. Boussaa, Y. Fautrelle, K. Zaidat, O. Budenkova, B. Saadi, X-D. Wang, L. Hachani, H. Ben Hadid

"Comparison of experimental data obtained in a benchmark experiment of solidification of a Sn-3%wt.Pb ingot and numerical results of two-dimensional and three-dimensional simulations of the process is presented. The benchmark experiment consisted in solidifying a rectangular ingot of Sn-3%wt.Pb alloy using two heat exchangers. Conditions of solidification were thoroughly controlled due to six thermocouples embedded into each heat exchanger. Due to another array of thermocouples the evolution of the temperature field at a lateral wall of the crucible was registered during the whole experiment. A treatment of the temperature data provided an estimation of the velocity field in the experiment. Post-mortem analyses of the sample provided the pattern of macrostructure of the sample and qualitative segregations pattern. 2D and 3D numerical solidification models are developed to give the distribution of the solute in a solidified sample.IntroductionConvection, either natural or forced, plays a very important role during the solidification. Its intensity and flow pattern affect heat and mass transfer and, consequently, macrostructure and segregation in a solidified ingot [1-4]. The effect of buoyancy convection during solidification has been studied in many laboratory-scale experiments [5-6]. Due to these experiments a general comprehension of formation of various defects in the ingot has been achieved. However, mentioned studies were not consistent since alloys, solidification conditions and configurations were every time chosen arbitrary. That is why the role of each parameter characterizing solidification process remains unclear. Moreover, the question of reproducibility of defects under the same solidification conditions still exists. In addition, most of the experiments suffer from the insufficient knowledge of control parameters that makes difficult their use for validation of models for solidification. These parameters serve as boundary conditions for numerical modeling and their incomplete description leads unavoidably to the errors in simulations. This situation motivated us to develop a setup for benchmark solidification experiments and to perform a set of the solidification experiments which we reported in [7]. Here we presented a comparison between results obtained in a benchmark experiment of solidification of Sn-3%wtPb ingot and its numerical modeling, which was performed in two-dimensional and three-dimensional configurations."

Jan 1, 2012

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003