Search Documents

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By Vadym Drozd, Yongzhou Sun, Shah Najiba, Jiuhua Chen, Andriy Durygin

"Phase transitions of the potential hydrogen storage compound, ammonia borane (NH3.BH3), was investigated using Raman spectroscopy and a diamond anvil cell at high pressures up to 9.5 GPa and low temperatures down to 90K. At room temperature, ammonia borane has three phase transitions in this pressure range. Upon cooling, four new phases were discovered through changes in characteristic Raman spectra. This result provides information about the stability of new bonding characteristics of this potential hydrogen storage material at low temperature and high pressure region.IntroductionDevelopment of hydrogen technology requires the safe, efficient and environmental friendly materials for hydrogen storage and hydrides have attracted much attention as hydrogen storage media. Among chemical hydrides, ammonia borane (BH3NH3) stands out due to its high gravimetric and volumetric hydrogen density ' "". Despite high hydrogen content, this compound is very stable. It releases hydrogen in several steps by thermal decomposition in the temperature range of 100°C to 500°C. Direct thermal decomposition also causes toxic borazine emission. Recent research interests on ammonia borane include destabilizing this compound to lower the dehydrogenation temperature with an enhanced hydrogen release rate using different techniques, e.g. the nanoscaffolds'', ionic liquids"" and acid'"" or transition metal catalysts' ""'. As a molecule of ammonia borane consists of protonic (NH) and hydritic (BH) hydrogens bonded by the polarized dative bond, thermal or catalyzed decomposition requires breaking of N-H and B-H bonding. Still now, the detailed information about the bonding characteristics of ammonia borane is not sufficient to understand details about its phases and structures. The development of methods to enhance hydrogen discharge rate from ammonia borane requires a detailed study about the structural and dynamical properties that control the stability and the intermolecular interactions of this material. This study is motivated to investigate the stability of the existing phases and also to explore the existence of any new phases at different temperatures and pressures which may have enhanced hydrogen release and uptake properties."

Jan 1, 2012

By Nicola Baldo, Marco Pasetto

"Recycling of tyre rubber in the road pavement, may be one of the best way to reduce waste tires in large quantities and, at the same time, improve some engineering properties of asphalt mixtures. The paper discusses the results of an experimental study, developed in order to analyse the potentialities of crumb rubber from road tyres in bituminous mixtures, using the dry process. Two types of porous asphalt mixtures and reference mixes without rubber were formulated by the traditional Marshall methodology, and mechanically evaluated by means of the Indirect Tensile Stiffness Modulus test, the Creep test (with confinement), and the Indirect Tensile Fatigue Test. Results of this study indicate that the tyre rubber has a positive influence on the performance characteristics, depending also on the grading and volumetric properties of the mix being studied: an interesting increase of the fatigue life, a better stiffness behaviour at lower temperatures and a bigger permanent deformation resistance at high temperatures are guaranteed. Introduction Recycling the rubber from used tyres, in the construction of road pavement layers, is potentially one of the more interesting and advantageous solutions from both the technical and environmental points of view, in order to reduce the total amount of car and lorry tyres to dispose. In road-building techniques, a technology, termed “wet”, for modifying bituminous binders with crumb rubber has by now become well consolidated. There have been numerous scientific studies conducted on this technology and its applications, particularly in the United States, where it has been adopted and codified in specific technical regulations (ASTM D-6114). If the wet process can be considered amply tested, the same cannot be said for a second technology, termed “dry”, which deserves careful study to evaluate its suitability and advantages. In “dry” processes, the rubber is usually used as a partial substitute of aggregate of equivalent grading and mixed with bitumen after integrating the crumb rubber in the lithic skeleton."

Jan 1, 2008

By Uchil Jayagopal, P. V. Krupakara, S. Manjunath

"This paper deals with the corrosion characterization of quartz particlate ZA-27 alloy metal matrix composites (MMCs). Quartz particles of size 50-80 microns are used as reinforcement. MMC's are prepared according to ASTM standards. Composites containing. 2, 4, and -6% by weight of quartz and unreinforced matrix were tested using 1 -N hydrochloric acid: The composite was found to be more corrosive resistant than matrix alloy. In each test the corrosion resistance of both alloy and composites were found to decrease with the exposure time.1. IntroductionMetal matrix composites- (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight 1-5. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments Particles reinforced MMCs has been the most popular over the last two decades.ZA alloy MMCs have most popular families being represented by. ZA-27 alloy reinforced with ceramic particulate. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior.ZA alloys have been used extensively in industry. This is attributed to their excellent fludity, castability and good mechanical properties. Among the zinc-based foundry alloys, the ZA family of alloy have been widely used during the past few years. ZA alloys have many advantage over aluminium based ones, especially high strength with a low casting temperature 8."

Jan 1, 2000

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By John A. Vallomy

"The CONSTEEL Process introduces a new concept in electric steelmaking by continuously feeding-preheating-melting and refining ferrous scrap or direct reduced iron. The process uses the furnace off-gas and fuel to preheat the scrap in a specially designed preheater. Thermal incineration of the flue gas reduces the carbon monoxide level to the more stringent requirements. Hot water or steam production from heat of flue gas is optional. The tap-to-tap time is set to match the cycle of the caster. The steel is treated via ladle metallurgy. The environment inside and outside of the steelplant is improved by decreasing levels of noise and hazardous emissions. Energy consumption decreases and disturbance to the electric network is eliminated. A CONSTEEL prototype was tested at Nucor Steel, Darlington, SC. A greenfield project is in the completion stage at the Florida Steel plant of Charlotte, NC, USA. The Process PhilosophyThe philosophy of the CONSTEEL Process is not solely to enhance efficiency; this was just a natural result of the change from a batch to a continuous practice. The primary objective in development was four-fold:1) 100% process control2) Rational use of available energy3) Improved environment inside and outside the plant4) Stability of energy input from the power systemIt was to make electric steelmaking more a science than an art and amenable to modern automation.The Basic Concept of CONSTEELThe concept of the process is shown in figure and includes basically a continuous feeding system, a preheater and a melting - refining furnace. A pre-established amount of heat is introduced into the scrap while traveling through the preheater using the sensible and chemical heat contained in the furnace off-gas and additional fuel. Melting-refining is carried out in the electric furnace. Slag formers, slag foaming additions and oxygen are injected to refine the melted steel continuously, to minimize the refractory erosion, to shield the arc, thus optimizing the transfer to the metal bath of the heat generated in the arc, to keep the bath homogeneous in composition and temperature and to produce carbon monoxide (CO) which is fuel for the preheater."

Jan 1, 1988

By Xu Weimin

The existing copper electrorefining tankhouse of Jinchuan Nonferrous Metals Complex (JNC) was commissioned in 1986 for refining blister copper anodes. Blister copper is produced by reverberating chalcocite separated from converter high grade nickel-copper matter by means of flotation. Special chemical analysis of the anodes shows, a composition of 93.02 - 95.72 % copper, 3.0 - 4.96 % nickel and 0.5 - 1.23 % sulfur. The wide range of composition makes the electrorefining process fairly different from others throughout the world. The initial nickel content of 20 ppm and sulfur 40 ppm or more in copper cathodes are reduced to 8.5 ppm and 11 ppm respectively. Since 1986 the tankhouse has undergone significant evolutionary modifications and implementations to ameliorate cathodes quality desirably. The important fact is that the N-additive was utilized through many studies and pilot and field trials successfully. While our primary purpose is to improve chemical quality of the cathodes, tankhouse capacity is increased considerably and the process is perfected satisfactorily. The tankhouse is described with special emphasis on JINCHUAN PROCESS. The upgrading of our product by the utilization of the N-additive is highlighted. The other aspects of the tankhouse including spent electrolyte treatment and by product nickel sulfate manufacturing are briefed as well. Key words: JINCHUAN PROCESS, anode, cathode, electrolyte, electrorefining, N-additive.

Jan 1, 1993

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By Alexandre Bonan

The paper reports on the results of a kinetic study on the oxidation reaction of aqueous free cyanide ions with H202, in the presence of Cu(2+) catalyst. The variables and respective ranges studied were the following: (CN) ° = 10 -100 mg/l pH = 10 -11 (H202/CN) mol ratio = 1 -3 (Cu/CN) mol ratio = 0 -0.25 The results lead to the development of a semi-empirical model whish incorporates both the useful oxidation reaction and the parallel alkaline decomposition of H202.

Jan 1, 1992

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By A. C. Cascalheira, L. M. Abrantes, M. Savic

This paper reports our results on the application of a novel process for the spontaneous and sustained reduction and recovery of elemental silver and gold on an electroactive polymer surface. This work incorporates the metal recovery from photographic films (silver) and goldsmith residues (gold), by direct contact of metal containing solutions with polymer. The performance on such process of electrochemically and chemically prepared polyaniline (P ANI) is evaluated. SEM coupled with EDX and XRD analyses confirmed the presence of metallic silver and gold deposited onto polymeric material.

Jan 1, 2000

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting. lime roasting. is being tested for retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04). oldhamite (CaS). calcium sulfite (CaS03). hematite (Fe2O:J), magnetite (Fe304). and minor amounts of pyrrhotite (Fe1.xS) and pyrite. At 600°C. 650°C and 700°C. the main constituents are anhydrite. oldhamite. and hematite. At 750°C. 800°C. and 850°C. anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides. calcium sulfite. hematite. and minor oldhamite. magnetite. and pyrrhotite. At 650°C. 700°C, 750°C. and 800°C, anhydrite, oldhamite. arsenic sulfides, and hematite are present. At 850°C. the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CIM) in the determination of the calcium-sulfur-oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RIM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1991

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012