Search Documents

By Samuel Senanu, Benjamin Agyei-Tuffour, Lifeng Zhang, Eivind Øvrelid, Adegboyega Nathaniel Femi

"The solar grade silicon ingot produced from directional solidification process usually pushes the impurities to the top and finally cut off and discarded, which leads to material loss. The hard inclusions lead to wire breakages during the cutting of the ingot in wafers. The main kinds of inclusions found in solar grade silicon have been investigated using vacuum filtration: needle-like Si3N4 and lumpy SiC inclusions. Clusters of SiC inclusions and Si3N4 are also found. Surface observations of the scraps before polishing reveals that Si3N4 inclusions are usually bigger and in some cases can be about a few millimeters. SiC inclusions are usually smaller, ~200µm but can be ~500µm in some cases. Inclusions observed after filtration are mainly SiC with diameters ~10µm. Through the vacuum filtration, 99% inclusions can be removed 99%. The possible mechanisms of filtration are cake filtration for the larger sized Si3N4 and SiC inclusions and deep-bed filtration the SiC inclusions. For the directional solidified silicon ingot, an approximate distance of ~10mm gave an encouraging cutoff thickness. The inclusions sizes were below 10µm. Introduction The search for an alternative source of energy to fossil fuel has led to a dramatic increase in the demand for solar energy due to its high dependability (abundant in nature) and environmental friendliness 1). During the last 5 to 10 years, the annual worldwide production of solar cell by the photovoltaic industry has increased to an annual rate of 30 to 40 percent 2). A necessary condition for the maintenance and even an increase of this growth rate is a decrease in the cost of feedstock for the solar cell production 1). The total international production in 1997 was 130 MW worth more than $500 million. In 2004 the consolidated world total production of PV cells increased to 1146 MW or around. $7 billion (Figure 1) 3). Silicon is currently the most dominant semiconductor material used in the PV industry. As shown in Figure 2 3), solar cells consist of two types of material, often the p-type and n-type silicon. Light of certain wavelengths are able to ionize the atoms in the silicon (causing atoms to either gain or lose electrons) and the internal field produced by the junction separates some of the positive charges (“holes”) from the negative charges (electrons) within the photovoltaic device. The holes are swept into the positive or p-layer and the electrons are swept into the negative or n-layer. Although these opposite charges are attracted to each other, most of them can only recombine by passing through an external circuit outside the material because of the internal potential energy barrier. Therefore if a circuit is made, power can be produced from the cells under light because the free electrons pass through the load to recombine with the positive holes."

Jan 1, 2008

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By Jing Zhan

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. The composition and morphology of fibrous precursor were characterized by XRD, IR, DTA/TGA and SEM analysis. The results show that XRD pattern and composition of the precursor with fibrous morphology precipitated at pH=9.0 were different from that of ß-CoC2O4?2H2O precipitated at pH=1.0. The mechanism on the thermal decomposition of fibrous precursor was addressed. The influences of various conditions in pyrolysis, including the temperature, time, atmosphere, and the morphology of the precursor, on the morphology, average size and specific surface area of the Co powders were investigated in detailed. At last, the final product, fibrous cobalt powders with diameter about 0.3~0.5µm in size and 40~60 in aspect ratio, were produced by thermal decomposition at 400~500? in the weak reducing atmosphere. The structure of pores in cobalt powders was capillary tube with open ports and the majority was mesoporous.

Jan 1, 2009

By Dajian Wang

To obtain the thermodynamic properties of a multicomponent liquid alloy system over the whole range of concentration at an arbitrary temperature, the free volume cell theory has been applied to derive the formula of activity coefficients of liquid solutions based on the infinitely dilute solutions at some temperature. The linear logarithmic relationship between activity coefficients of binary dilute solutions and reciprocal of absolute temperature have been verified, and are in good agreement with the experimental values from the literature. The Monte-Carlo algorithm was used to calculate the nonlinear end value equations of binary systems, then the free volume parameters obtained were correlated with the activity coefficients of liquid binary, ternary, and quaternary systems at an arbitrary temperature. Three dimensional a-X-T diagrams of some binary systems representing the temperature and concentration dependence of activities were plotted. The calculated results regarding non-ferrous alloy systems have been statistically examined with the experimental values from the literature. Hence, this simple approach could be useful for analyzing thermodynamic properties of liquid alloy systems.

Jan 1, 2000

By Sergio N. Monteiro

Jute fabric obtained from discarded sackcloth is a promising low cost and post-used material being considered as reinforcement of polymeric matrix composites. In particular, the combination of this fabric with a recycled plastic constitutes an environmentally correct composite with both economical and environmental advantages. The present work investigates the toughness of recycled polyethylene composites reinforced with up to 40 wt% of post-used jute fabric extracted from discarded sackcloth. Standard Izod notched specimens were impact tested and the results showed an increase in toughness with the amount of jute fabric. Observation of the composite fracture by SEM revealed that the fabric weave, in spite of damages caused by the previous use of the sackcloth, act as an effective obstacle to crack propagation.

Jan 1, 2009

By Peter V. Barr

Despite the advent of modem firing control systems reheating furnace operations frequently allow significant thermal excursions in the discharged slabs or billets after furnace delays. Although HSM furnaces are not immune to this and other related problems, mini-mill operations are most vulnerable due to their more frequent delays and (often) less sophisticated control systems. In order to reduce these problems control systems will commonly include a thermal model, operating either on-line (interacting directly with the controller logic) or in an advisory, off-line mode. Using a new 'fast' thermal model, the paper examines the thermal response of a typical mini-mill furnace during both delays and the subsequent recovery period. A variety of firing strategies are explored and compared on the basis of maintaining thermal excursions within allowable limits for rolling. Other factors, such as the potential for overheating of billets within the furnace during delays and the overall thermal state of the furnace, are also considered in some detail. Although common practice, the use of conventional thermocouple zone temperatures for furnace control during and after delays is shown to be a dubious proposition. Keywords: Reheat Furnace, Modeling, Process Control

Jan 1, 2003

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Onsan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By P. F. Stratton, M Huggahalli, N Saxena

"Several studies have been carried out to determine how the optimum atmosphere conditions in the heat treatment of metals can be established for a given product by using different gas injectors and varying atmosphere flow rate and composition. The most common approach taken to gain insight into furnace atmospheres has been to use commercial computational fluid dynamics codes and examples of their use are shown. However, the complexity of these codes, the difficulty in establishing boundary conditions, their cost and computational demands limit their usability in solving day-to-day production problems.A simplified, web-based model of a furnace atmosphere is described where the conservation equations are solved to determine the composition profiles of the atmosphere in the furnace. Although the model is restricted in scope to certain types of furnace, it is shown to give better results than CFD when boundary conditions are uncertain. The application of the model to the understanding of existing furnace conditions and to determining ways of optimising the use of gases are discussed. IntroductionThe important role of protective atmospheres during heat treatment of metals, furnace brazing of assemblies and soldering of printed circuit boards is well established. The atmosphere in the furnace prevents air ingress and oxidation of the parts, helps flush away any flux or binder from braze and solder pastes and provides an important mode of heat transfer [1]. In a batch furnace having typically one or two gas injectors, the gas utilisation and process can be optimised by minimising air leaks and mantaining atmosphere homogeneity with fans or other atmosphere circulation techniques. In a continuous furnace, however, atmosphere optimisation is more difficult as furnace inlets and exits can also let in air. The atmosphere requirements of different stages of heat treatment, brazing or soldering vary [2]. Achieving these atmospheres in different sections of the open-ended furnace is a relatively complex task. Methods such as atmosphere zoning and the use of physical curtains and gas injectors have evolved with time, though it is hard to predict how effective these techniques will be for a given furnace and process. Experts in the field tend to rely on experience and rules-of-thumb rather than scientific method to achieve the required results."

Jan 1, 2001

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By A. Haxhiaj, Mitovica, E. Haxhiaj

"The paper discusses problems encountered during the release and possibility of using the thermal gas quantity Mathematical models are used to calculate the positive thermal effects of the gases and losses of thermal quantity with gases in the melting process of electric furnaces. The paper discusses in details the percentages of CO, CO2, H2S, O2 and the humidity in gases and their impact on the technological process in electrical furnaces in Drenas. The paper also confers the quantity and temperature of gases, the transfer of thermal quantity and dust with gases in the environment. The paper presents the percentage of humidity in the load which is added in electric furnace for melting and its impact on thermal and environmental balance in the technological process of melting in electric furnaces. Key words: Furnace, load, temperature, humidity, gases.IntroductionNickel easily reacts with gases in the atmosphere of the furnace in which the nickel ore is processed. Such reactions can explain challenges in producing high quality nickel. Reductive atmosphere with the surrounding gases composed of sulphurous anhydrite has harmful effects on the production of nickel. This is mainly due to solubility of hydrogen as well as nickel oxide in the melted metal. Nickel reacts with carbon monoxide and forms carbide of nickel and nickel oxide which dissolve in the melted metal. Carbon monoxide also dissolves in the melted metal. The presence of carbon dioxide and water vapor in the atmosphere of the furnace impact the decrease of acidity in reductive atmosphere of the furnace. The carbon dioxide reacts with nickel and forms nickel oxide and carbon monoxide. Water vapor reacts with nickel and forms hydrogen and nickel oxide that have negative impact on the structure of nickel and its alloys. In this paper the analytical and experimental analyses are proposed that lead to minimization of the negative effects of gasses and humidity in the melting process. As the practical example, the electrical furnace in Drenas is analyzed.1. The Load and Its CompositionThe basic function of the rotational furnace is drying and reductive roasting of the ore which directly is loaded into the electrical furnace for melting. It is important to mention that the degree of roasting and pre-reduction of iron-nickel oxides is reached if the roasting process of the load in the rotational furnace is done at the temperature of 900°C to 1000°C, with the reductive atmosphere in the furnace and with minimal amount of oxygen in the processing gas. The optimal process of roasting and pre-reduction of the load in its mass is around 13 wt%. With the removal of the humidity and the sterile pare of the ore, with the positive impacts in utilization of the thermal and electrical energy in the melting process in electrical furnaces."

Jan 1, 2013

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By J. E. Dutrizac

A mineralogical study of a weak acid leach residue from the Clarksville zinc plant of Savage Zinc Inc. was carried out. The study focused on Pb and Cd as these elements most significantly impact on the environmentally acceptable disposal of the residue. The residue consists of major amounts of bassanite, zinc ferrite and various Zn-Pb-Fe-Cd silicate species. Also present are lesser quantities of PbSO4, sphalerite, Fe2O3 quartz, Mn-Pb-Fe oxides, SrS04, (Pb,Sr)SO4 iron gel-silica gel, jarosite and Ti oxide. The principal Cd carriers are the zinc ferrite, which contains up to 9.00% Cd and likely accounts for -45% of the total Cd content of the residue, and the various silicate species which contain up to 6.97% Cd and account for about 45 % of the total Cd. The sphalerite is a minor Cd carrier containing an average of 0.35 % Cd and accounting for -5 % of the total Cd; the other carriers contribute only trace amounts to the total Cd content. The major Pb carriers are PbS04, Pb-bearing silicates and Mn-Pb-Fe oxides. Minor proportions of the total 1.09% Pb content of the residue are carried by SrS04 and (pb,Sr)S04' Trace Ph carriers include the iron gel-silica gel, Fe-Zn-AI oxide and bassanite. The residue after the toxicity characteristic leaching procedure (TCLP) is mineralogically very similar to the initial weak acid leach residue; the amounts of calcium sulphate are approximately the same in the two products. The principal Cd and Pb carriers are also the same as those noted in the initial residue, except that some dissolution and reprecipitation of Pb-Sr sulphate takes place. That the residue fails the TCLP test is likely a consequence of the superficial dissolution of Pb and Cd from species such as PbS04 or Zn-Pb-Fe-Cd silicate.

Jan 1, 1995

By P. R. Taylor

Laboratory experiments have been performed to evaluate the kinetics of roasting pyrite and arsenopyrite in air at elevated temperatures, in the presence of lime. The effects of temperature, time, air flow rate, particle size, lime type, and mineral/lime weight ratio on the rates of oxidation, lime sulfation, and lime arsenation were studied. The reaction products were identified using chemical analysis, x-ray diffraction, SEM analysis, and optical microscopy. The results are discussed in terms of the utilization of lime to capture sulfur and arsenic during the roasting of refractory precious metal concentrates. More than 99.9% of the arsenic and 98% of the sulfur are contained when roasting pyrite and arsenopyrite with hydrated lime under typical roasting conditions.

Jan 1, 1991

By William A. Apel

Several different strains of bacteria have been shown capable of reducing hexavalent chromium, Cr(VI), to Cr(III), a less toxic, .. more readily recoverable form of Cr. This paper examined the Cr(VI) reduction efficacies of 3 different Cr(VI) reducing bacteria: Pseudomonas f1uorescens LB300., Pseudomonas aeruginosa PAOI, and Pseudomonas aeruginosa PAOI (pCROI) It was demonstrated that all three bacterial stratns reduced Cr(VI) primarily during their exponential growth phases while using glucose as their carbon and energy source. Significant differences in the three organisms' Cr(Vl) reduction capabilities depending on initial Cr(VI) concentrations were also demonstrated. P. aeruginosa PAOI showed superior Cr(VI) reducing capabilities over the. entire range of Cr(VI) concentrations tested while the Cr(VI) reduction capabilities of the other two strains were increasingly inhibited as Cr(VI) concentrations increased.

Jan 1, 1991

By H. Y. Sohn, S. PalDey

"A new chemical synthesis process for the preparation of intermetallic compounds has been developed. It involves the vapor-phase reduction of mixtures of constituent metal chlorides by magnesium vapor to produce intermetallic compounds in the form of fine powder. The advantages of the process include (a) the use of inexpensive raw materials, (b) low reaction temperatures, and (c) products in the form of fine particles. Titanium and nickel aluminides were prepared by this method. The effect of AlCl/TiCl3 partial pressure ratio on the formation of different titanium aluminides was studied. A two-phase mixture containing 80 mol % of TiAl and 20 mol % of TiA13 formed at an AlC13/TiC13 ratio of 10. The amount of TiA13 was maximized to 72 mol% at an AlC13/TiC13 ratio of 16. The maximum conversion of the limiting chloride TiCl3 was 94 % . In the case of nickel aluminides, NiAI, NiAl3, and Ni2Al3 were formed by reducing mixtures of NiC12 and A1Cl3 vapors. The effect of the partial pressure ratios AlCl3/NiC12 and Mg/NiC12 on the formation of nickel aluminides was studied. The maximum content of NiAl obtained was 98 mol % . At the AlC13/NiC12 ratio of 19, a two-phase mixture of 17 mol% of NiAl and 83 mol% of NiA13 was produced. The product particles were very fine in the size range of 0.05 to 0.2 µm.A. IntroductionIntermetallic compounds are attracting much attention [1]. Titanium and nickel aluminides have attracted a great deal of attention from the aerospace as well as automobile industries because of their potential for high-temperature application (e.g., low density, good oxidation resistance, and high-temperature strength retention [2, 3]). Gamma TiAl and two-phase (TiAl and Ti3Al) alloys [4] are used for gas turbine engine rotational components as well as automobile exhaust valves. TiAl3 is one of the most extensively investigated aluminum-rich intermetallics. Nickel aluminides are attractive because of their low densities, relatively high melting point and good high-temperature strength properties. For example, Ni3Al shows increasing rather than decreasing yield strength with increasing temperature [5]."

Jan 1, 1998

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By Christoph Beckermann, Kai Liu, Richard A. Hardin

"A two-dimensional heat transfer model for transient simulation and control of a continuous steel slab caster is described. Slab thermal and solidification conditions are computed by the model as a function of time-varying casting speed, secondary spray cooling water flow rates and temperature, slab thickness, steel chemistry, and pouring and ambient temperatures. A solidification model that includes the effects of steel chemistry, cooling rate and mierosegregation on the solidification path is incorporated directly into the caster model. Comparisons between measured and predicted liquidus and solidus temperatures are given for two low alloy steels, and show good agreement. Predicted and measured slab surface temperatures recorded on an operating caster are compared with this transient model and show that the model can predict the temperature response at the slab surface. Results of several simulations are given to demonstrate the effects of changing casting conditions on the slab thermal profile and the solidification end-point. A control methodology suitable for online control of a continuous casting machine is described, and its ability to control the surface temperature profile by dynamically adjusting secondary spray cooling flow rates is demonstrated using the simulator. IntroductionIn order to remain competitive in today's world-wide market for continuously cast steel products, steel producers are finding that it is ever more important to implement process control and to develop a more thorough technological understanding of their casting process. By integrating process control and monitoring into both production and quality control, producers are better able to meet customers' demands for steel of the required quality, quantity, size, grade, and properties at the lowest cost. Computer models used for real-time/on-line prediction and control of continuous steel casters are fundamental tools to accomplish this. Accurate on-line prediction and control of steel solidification and heat transfer allows for more flexibility in caster operation by giving operators the ability to change casting speeds while keeping critical process parameters within required ranges. Such control 'capability also results in more uniform quality throughout an entire casting sequence from startup to shutdown. Furthermore, due to the unreliability of temperature sensors, and the lack of good sensors for important process parameters such as solidification end-point and liquid pool depth, computer-based control models are often the only available option."

Jan 1, 2000

By Aert Driessen

Australia has large resources of rare earths -- 4.35 Mt of contained rare-earth oxides (REO) in the demonstrated category and 1.69 Kt in the inferred category. Australia's demonstrated REO resources are contained in about equal proportions in placer deposits, which also host Australia's titanium and zircon resources, and in hard-rock deposits. The largest single deposit of rare earths, at Mount Weld in Western Australia, is contained in regolith overlying a carbonatite pipe. It has a demonstrated resource of 1.73 Mt of contained REO and yttrium oxide. The largest demonstrated resources of REOs in placer deposits are in the Murray Bash, southeastern Australia -- a total of 1.90 Mt of contained RE0 in six deposits. However, the REO-bearing minerals (monazite and xenotime) are of secondary importance and their recovery will be determined by the market for titanium dioxide and zircon. The Murray Basin and other pre-Pleistocene basins offer the greatest potential for discovering more REO resources. Australia produces about 7000 t/year of REO in monazite and xenotime nearly all from Western Australia, as by-product of mineral-sand mining; monazite production is about 12 000 t/year (6600 t REO) and intermittent xenotime production is about 50 t/year (25 t REO). About 8000 t/year of monazite containing about 4400 t REO is not recovered separately, or is lost in tailings, as is an unknown but smaller amount of xenotime.

Jan 1, 1992

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993