Search Documents

By Marek J. Mrugala

Coal strength based on scaled uniaxial compressive strength from the laboratory and back calculations from in-mine observations of pillar stability indicate that material strength scaling rules are open to debate. Analyses presented indicate that the application of scaling factors lower than 0.5 provide a better correlation with field observations of pillar stability.

Jan 1, 1989

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By Laxminarayan Holla

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

By David C. Oyler

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation, topping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented,

Jan 1, 2001

By Anthony T. Iannachione

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures. Microseismic activity associated with these roof falls occurs in distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fall can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

Jan 1, 2001

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By Tim Burgess

Patton Mining, LLC and J.H. Fletcher Company recently collaborated and mechanized the sometimes hazardous, and always labor intensive, process of installing standing steel supports during the construction of a slope entry of a new mine. The new innovation is a beam setting machine design that can lift and maneuver heavy steel beams into place over and around the belt and vent tubing. In addition, the machine is designed with an integral double extending lifting work platform to allow workers a stable work area from which to install metal sheeting between the beams. The previous method to install the heavy steel supports and the steel sheeting included multiple workers lifting heavy loads frequently on stepladders. This paper will inform the reader of how Patton?s major goal to develop the safest, most continuous slope development process possible was achieved and the beam setting machine that evolved from the project.

Jan 1, 2011

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Tom Denton

The bolt design criteria, since it was first published by Dr. John Stankus (Stankus, 1997), has been recognized as an important tool in ground control design. This concept is based on the Optimum Beam Building Effect (OBE), which is defined as the roof beam that has no separation above or within the bolted range and having the shortest bolt possible. This paper will present an application of this concept at the American Coal Company. Galatia mine. This mine previously used a 6' and 7' length bolt. However, since seam thickness has gotten smaller in the Southern area of the nine, a two-piece bolt is required. A two-piece bolt increases ground control costs and delays production. Therefore, a one-piece, shorter bolt, if feasible, can reduce costs and expedite development. In this analysis, Computer modeling is first conducted to determine bolt length and installed load. Second, a special bolt is developed, that can achieve the proper installed load as determined by the computer modeling. Third, underground bolt pull and load cell tests were conducted to evaluate bolt performance. Finally, an underground "bench" test was conducted. The test results have shown that entry convergence in the short bolt (5) test area is less than the 6' bolt area. Overall roof condition in the test area was as good as the 6' bolt area. Based on this analysis, the mine has converted to a shorter bolt in the low seam area and it is working well.

Jan 1, 2000

By Larry Stolarczyk

The mining industry would benefit greatly by imaging geologic conditions well in advance of mining. In layered deposits such as coal, trona, quartz, and potash, natural waveguides form and enable electromagnetic seam waves to travel great distances. In the early 1980s, the Radio Imaging Method (RIM) was developed to capitalize on electromagnetic seam wave propagation in the assessments of seam conditions in longwall panels. The initial applications of RIM tomography and comparisons to in-mine mapping of geologic conditions proved that faults, paleochannels, and rapidly thinning coal could be detected and imaged with seam waves. This paper describes the application of electromagnetic seam waves in mapping the margins of a paleochannel crossing a longwall panel and the interesting possibility of adopting the newly developed Full Wave Inversion Code (FWIC) )Newman 1995) to significantly improve imaging resolution. When tomography images are combined with ground control science, a significant reduction in cost, roof fall potential, and waste rock in underground mining may be realized.

Jan 1, 1999

By Salah Badr

Longwall mine layouts with their entries, chain pillars, face support systems, advancing mining faces and compacting gobs represent a geomechanically complex mining operation. Geomechanical aspects are further complicated if mining occurs at depths exceeding 350 m, as stresses induced adjacent to the excavations exceed the unconfined strength of the coal and result in fracturing of the sidewalls of entries and chain pillars during development. Traditional methods of geomechanical analysis, whether empirical or numerical, are unable to represent such behavior satisfactorily. Achieving some meaningful results requires explicit representation of the three-dimensional boundary conditions and implementation of appropriate constitutive models for the rock mass. This paper describes a numerical modeling methodology for deep longwall mines operation using the FLAC3D finite difference de, which incorporates a strain softening constitutive law for modeling failure of coal. An important aspect of the modeling method includes accounting for stress relief provided to the pillars and entries due to the increasing load applied to the compacting gob.

Jan 1, 2003

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Kot Unrug

Fully grouted tensioned bolts provide a desirable compressive of laminated roof and bondage along the entire bolt length, at the same time the entire surface of the hole is protected against penetration of moisture. This is particularly important in shale strata, where, when left unprotected by a partial grout column, moisture penetrates to the annular space, and weathers rock around the bolt hole, having an easy access to the bedding planes which are strongly hydrophilic. The most desirable are thrust tensioned rebar bolts that can be installed with one procedure step, and can secure a desired pre-stressing. Such bolts have a forged conventional head and offer no hazard to miners in low clearance mines, whose number increase constantly due to the depletion of reserves in thicker seams. The presented field-testing program has been based on instrumented bolts allowing for monitoring of tension at installation and at a chosen time interval after. The tested system is based on rebar bolts installed with two speed Fosroc resin (fast at the top and stow at the bottom), and mechanical compression by the bolting machine at installation. Combination of several different washer -- plate arrangements have been tested. The results are reported with their interpretation, and recommendations directly towards strata control requirements, as well as the operational considerations for efficiency of installation.

Jan 1, 2002

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By Gregory Hinshaw

Underground mine bolting machines have evolved since inception in the 1940's due to the need for increased safety and productivity. However, major design innovations historically came from changes in the mining plan and the mine environment. During the last ten years, productivity needs have outpaced the evolution of existing designs. J. H. Fletcher & Co. has responded with a commitment to research and development which has fostered several new designs. The most recent machine built is a walk through crawler frame powering four drilling units simultaneously with semiautomatic computer control using two operators. This machine utilizes technology to create a safer yet more productive roofbolter for continuous mining sections utilizing place changing methods.

Jan 1, 1998

By Michael Gauna

In 2010, the number of fatal rib falls in U.S. underground coal mines exceeded fatal roof falls for the first time ever. While recent trends have seen roof fall fatalities reduced by about 62% since the 1990s (from an average of 9.6 per year in the 1990s to 3.6 per year during the last five years), the incidence of rib fall fatalities has remained approximately constant (about 1.5 per year). In addition, injury incidents associated with pillar rib failure have been steady at approximately 100 per year. The persistence of rib fall injuries, underlined by the recent increase in rib fall fatalities, has led to this investigation of the coal rib failure parameters and methods available to mitigate rib failure in U.S. underground coal mines A detailed study of the 21 fatal rib fall incidents that have occurred since 1995 (excluding coal burst incidents) indicates that the two most important risk factors are the mining height and the depth of cover. The depth of cover was 700 ft (213 m) or greater in 81% of the fatalities, and the mining height was at or exceeded 7 ft (2 m) in every instance but one. Other risk factors included multiple seam interactions, rock partings in the seam, and retreat mining. The accident history reveals that joints or slickenside features within the rib increase the hazard. Approximately threequarters of the rib fatality victims were roof bolting machine operators and continuous mining machine operators. This paper includes a brief overview of techniques for rib control; including bolts, standing support, bent steel straps, and rib strapping. The available mining equipment features for installing rib support and protecting operators from rib falls are also discussed. A proactive approach to rib control using available technologies will lower the risk to miners and is an endeavor that must be pursued to reduce rib fall accidents.

Jan 1, 2011

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001