Search Documents

By Tetsuji Hirato, A. J. Monhemius, Yasuhiro Awakura, G. W. Warren, E. Peters

An electrostatic pseudo-liquid membrane technique, in which extraction and stripping take place simultaneously in a single reaction vessel using an electrostatic dispersion, was applied to recover Ni(II) from aqueous 0.1 kg m-3 Ni(II)(as NiSO4) – CH3COONa solutions, and the Ni(II) ions were concentrated by a factor of 9 into an aqueous 1.0 kmol m-3 HCI solution using D2EHPA as an extractant at the applied voltage of 3.7 kV for the dispersion. When the process of ESPLIM proceeds favorably, the concentration of Ni(II) in the upper part of the organic phase of the reaction vessel is lower than that in the lower part. In addition, the concentration of Ni(II) in the organic phase of the extraction chamber is higher than that in the stripping chamber. For the stable operation of this process, the stripping rate must be greater than the extraction rate to prevent the excess accumulation of Ni(II) in the organic phase which leads to the poor dispersion of the aqueous phase.

Jan 1, 1993

By Don Macfarlane, Brian Heer, Tom Martin

The Manapouri Power Station, commisioned in 1969, is located in Fiordland National Park in the South Island of New Zealand. It is the country’s largest hydro power scheme and can generate 700MW of electricity. The power station utilizes the hydraulic head of Lake Manapouri, using an underground power station and a 10 km-long tailrace tunnel was constructed by drill-and-blast to allow discharge to Doubtful Sound. Power generation fell short of expectations due to higher than expected friction in the tailrace system. To remedy this a second tailrace tunnel was constructed between June 1998and May 2002. It consisted of a 10 m diameter, 10 km long tunnel in predominately gneissic rock and was excavated using an Atlas Copco Robbins TBM. High water inflows, Owner/Contractor production incentives and a major claim settlement were handled during the 5 1/4 year project. This paper discusses TBM advance rates, utilization factors that increased in the second half of the project plus an innovative method for sealing Tunnel 1 to construct the bifurcation.

Jan 1, 2003

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By T. C. Rao, Vanangamudi. M., J. P. Barnwal

Experiments were carried out on 76 mm laboratory heavy medium cyclone treating -2.0 t 0.5 mm coal and on two 600 mm industrial heavy medium cyclones treating coal in the size range -13.0 t 0.5 mm. The variables studied were spigot diameter and feed medium gravity. The generalised distribution curve for the separation of coal in these heavy medium cyclones has been defined by the equation [ ] The specific gravity of separation SG has been found to increase linearly with increase in feed medium, gravity (SGf). The relationship for SG of industrial cyclone is given as 50 SG = -6.801 t 6.463 SGf t 0.0327 Spig 50 -0.02625 SGf. Spig. Further, the probable error for the separation has been found to be linearly related to (SG50 - SGf ) according to the equation [ ] The model equations developed have been used to select appropriate levels of operating conditions to achieve an increase in the yield by about 2 to 4% without affecting the quality of the product.

Jan 1, 1990

By R. Sivamohan, F. Huang

A mineral processing strategy developed for the finely and complexly interlayered calcite rich wollastonite, microcline, and iron-garnet ore of Jokkmokk, northern Sweden, gives an overall calcite recovery of 89.4% at a grade of 90.7% CaCO3. The wollastonite product assays 53.0% Ca- SiO3 at a recovery of 92.2%. The significant elements of the developed strategy are stepwise grinding, wet high intensity magnetic separation (WHIMS), reverse flotation and starvation flotation. Stepwise grinding avoids the overgrinding of soft calcite. WHIMS removes the colored iron-garnet impurity and thereby increases the whiteness of the product. Reverse flotation enables a simple flotation circuit and starvation `flotation helps to optimize the physicochemical conditions in cleaner flotation by giving rougher products of narrow particle size distributions. Moreover, with the reagent scheme developed in this work only one cleaner stage is necessary for the various rougher flotation products to be upgraded to give the foregoing results. In this paper, the strategy is presented in detail along with appropriate results.

Jan 1, 1990

By V. G. Papangelakis, G. P. Demopoulos

The high temperature (180-200 OC ) pressure oxidation (02 - HzSO4) process for the recovery of gold from refractory concentrates (FeS2/FeA8S) is simulated with the aid of a computer model. The model centers on the continuous operation of a multi-stage horizontal autoclave. In particular the effects of key process parameters controlling the autogenous operation of the autoclave are critically examined. The building elements of the model are (i) the continuous particle size distribution function of the concentrate, (ii) the residence time distribution function of the slurry and (iii) the shrinking core kinetics. Conversion is calculated on the basis of the segregated flow model. For the calculation of the particle size distribution at the exit of each compartment the population balance model is employed. The effects of feed rate, feed preheating, cooling, autoclave configuration and rate limiting regime (chemical reaction vs. gas-liquid mass transfer) on the autogenous steady state operation are discussed. Finally optimum reactor design and operation criteria are indicated.

Jan 1, 1990

By Serkan Saydam, Ercument Yalcin

This paper presents the results of Caldagi Nickel-Cobalt Ore Deposit's, located in Turkey, reserve and ultimate pit limit design analysis. Reserve analysis of any deposit requires two steps. First one is to constitute of block model of the deposit and second step is to generate ultimate pit limit. The block model of the Caldagi ore deposit has been created by means of geostatistics. The reserves of nickel and cobalt in this block model are defined as resource, approximately 12 million tons of nickel and 1 million tons of cobalt with average grades of 0.9% Ni and 0.03% Co, respectively. Ultimate pit limit analysis has been performed by considering economic, technical and legal factors. In this paper, the ultimate pit limits are generated by Lerchs & Grossmann (L&G) algorithm. As a consequence of ultimate pit limit design, total amount of tonnage to be excavated is 1.4 billions of tons, 700 million of which contains ore and 747 million of which is the tonnage of waste.

Jan 1, 2002

By R. E. Johnson, J. E. Dutrizac, B. R. Palmer

Silver sulphide (acanthite) and lead sulphide (galena) dissolve relatively rapidly in FeCl3 media with the formation of elemental sulphur and soluble silver and lead chlorides. Parabolic kinetics are observed, and the leaching rates are controlled by the outward diffusion of the AgCl and PbCl2 reaction products through the constantly thickening elemental sulphur layer formed on the sulphide. Hence, both leaching rates are strongly dependent on those variables which affect the solubility of AgCl or PbCl2 at the reaction interface. The rates therefore increase with increasing temperature and total chloride ion concentration, but decrease in the presence of elevated concentrations of AgCl or PbCl2. By contrast, neither sulphide is significantly attacked by ferric sulphate media, even at high Eh values. Although the reasons for the refractory behaviour of Ag2S in sulphate media remain unknown, the low rate of PbS attack is attributable to the passivating layer of PbSO4 and elemental sulphur formed on the surface of the galena.

Jan 1, 1993

By J. Stachurski, N. A. Abdel-Khalek

The objective of this investigation was to compare the results of countercurrent, column cell flotation vs. conventional (mechanical) cell flotation for the cleaning of a sulfur ore (-0.5 mm, 27.43% S) and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, column flotation produced concentrates of higher grade. For example, column cell flotation produced a nonwashed concentrate of 65.3% S with a recovery of 84.1%. However, conventional cell flotation produced a rougher concentrate of lower grade (57.0% S) and higher recovery (92.5%). At a superficial-wash water velocity of 0.265 cm/sec, the column product grade increased to 76.4% S, with a slightly lower recovery (80.3%). However, a concentrate with a similar recovery but a lower grade (74% S) than that of the washed product was obtained after three cleaning stages with the conventional cell. The column gave superior results for the flotation of fine and ultrafine particles.

Jan 1, 1994

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By Dennis C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required about 3 Mm2 (32.3 million sq ft) of fill over an area of about 600,000 m2 (6.5 million sq ft) in irregular terrain with relief of up to 40 m (130 ft). Earthwork construction was completed in about six months using mine waste, placed in 4 to 6 m (13 to 20 ft) lifts with mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10 m (33 ft). This was done to develop a mat for additional resistance to possible differential settlements due to the modest density of the fill and dynamic (earthquake) conditions. A single 2-mm (80-mil) high-density polyethylene (HDPE) liner was used below the leach pads. This was protected from the loading and unloading equipment by bedding and cover systems. It consisted of screened sand, gravel and silt as the bedding and cover layers and a heel of screened gravel and primary crushed low-grade ore.

Jan 1, 1995

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By J. Mattern

Performance monitoring, operational practices and ongoing collection of geologic data in open pit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike open pit has been ongoing since the early 1980’s, with its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls. With the proper available equipment, steepening of bench face angles via pre-split blasting is not an uncommon method for steepening of inter-ramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted resulting in quantified, rock specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2 degrees on a 300m high slope, without the necessary purchases and procedural changes that would be required for pre-split drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves. Location The Goldstrike open pit is located on the Carlin Trend gold belt in northeastern Nevada USA (Figure 1). The mine has produced over 43 million ounces (1.2M kg) of gold during the past 30 years. Engineering Geology Stratigraphy Figure 2 is a stratigraphic section of the rocks in the Goldstrike open pit. Quaternary alluvium and Miocene materials typically are poorly indurated stiff soils and are not present in all locations. Bedrock units consist of siltstones, mudstones, sandstones and cherts. From top down the major units exposed in the open pit are the Vinini Formation, the Rodeo Creek Unit, and the Popovich Formation. In general, rock mass strength increases with depth.

Jan 1, 2019

By T. Stack, C. Roos, M. Drake, P. Conrad

"This paper presents the evaluation Montana Tech completed for the Western Energy Company Rosebud Mine relating to the benefits of survey data collected using novel technologies over traditional methods for topographic surveys. These technologies include Unmanned Aircraft Systems (UAS), photogrammetry, and laser scanning/LIDAR. Utilizing these technologies, large areas such as reclamation areas and cast blasts can be surveyed in a timely manner for use by the mining operation. The areas that were evaluated were the improvements in the safety of employees and the time required to collect data. In addition, there is also a potential cost savings for the operation, all while not affecting the accuracy of the data that is collected. PROJECT BACKGROUND Accurate topographic survey data is critical to successful surface mining operations. It is used for mine planning and design as well as permit compliance. Currently, employees typically collect survey data using GPS equipment or total stations. These methods can be dangerous, as they require employees to work near large operating mobile equipment, edge of high walls, and on piles of stacked steep-sloped loose material. Aerial and satellite photographs, performed by a contractor, can be used to obtain some of this information, but it is expensive and may not be attainable during overcast conditions. Montana Tech, along with the Rosebud Mine, conducted research on the accuracy, cost, and other benefits of survey data collected using novel technologies. Some of the methods studied include, but are not limited to, Unmanned Aerial Systems (UAS) or Vehicles (UAV), photogrammetry, and laser scanning. These methods were evaluated to determine if these technologies provide mining companies with a safer, cost effective, and accurate method to collect data for surface mining operations. The project scope was to evaluate various surveying techniques to determine which techniques would be applicable for the Rosebud Mine and complete a trade-off study comparing the new techniques with currently used methods. The trade-off study included an analysis of the technological differences between the methods, safety and legal considerations for the new techniques, operational limits, and the costs associated with each technique. Working with the Rosebud Mine team, techniques were selected for field trial and accuracy comparison. This paper presents a literature review of applicable technical papers and a summary of the Federal Aviation Administration regulations for UAS, followed by a study comparing conventional GPS topographic surveys with UAS based systems and laser scanning systems. The comparison of the various methods was broken into the following four categories: operator safety analysis, time comparison, survey accuracy, and cost analysis. After all of these portions of comparison were completed a recommendation was provided based on the evaluation that was performed."

Jan 1, 2017

By T. E. Walsh

Introduction I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too ex

Jan 1, 1980

By R. C. Schmidt

The Mont Klahoyo magnetite deposit is located about 600 km northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 million tons grading 36% iron. The deposit, occurring at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations, is associated with amphibolites, pyroxenites and gneisses of the Liberian Shield. At Mont Klahoyo occur two separate iron formations of which the lower member is the ore body. This lower member consists of a highly metamorphosed - banded quartz-magnetite iron formation in which iron silicate bands alternate with beds of quartz-magnetite. mphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated overturned "Z" shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m and outcrops intermittently over a distance of approximately 5.5 km. Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K-1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) with the remaining quartz-magnetite units (oxide facies) repre¬senting the important ore zones of the Mont Klahoyo deposit. The ore-bearing "K" units are subdivided further, based upon their specific lithologies, iron content and concentration characteristics, into eleven ore types. The identification of these ore types is considered particularly important to mine planning and flowsheet design. A cap of oxidized materials overlies the primary quartz-magnetite iron formation but no enrichment has occurred. It is proposed that the Mont Kalhoyo iron formations were deposited, possibly chemically, in a volcanic environment as a siliceous iron formation with volcanism providing the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a relatively coarse-grained quartz-magnetite-silicate iron formation.

Jan 1, 1979

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By T. E. Walsh

I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too exi

Jan 9, 1980

By Noris Del Be1 Belluz

Drilling underground in the Grasberg dewatering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are used. Pilot holes probe ahead of the tunnel development to intersect aquifers ahead of the face. And dewatering holes dewater rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, static pressures of >8.3 MPa (> 1,200 psi) have been recorded with flows from a 100 mm (4 in.) HQ core hole measured at 5,700 L/min (1,500 gpm). The waterflows can be slightly acidic, necessitating the use of stainless-steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early on to deal with these conditions. PT Freeport Indonesia (PTFI) established procedures to maintain the safety of the drill crews, to enable coring of the rock, and to maintain the safety of the miners driving the drifts. The collar gear controls the waterflows because these drill holes are a vital source of water for the concentrator.

Jan 1, 1998

By S. J. Knoll, D. F. Scott, T. J. Williams

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep under-ground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004