Search Documents

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By Ray Soper

Important progress has been made in developing the K-Process as an alternative to cyanide as a method of recovering gold from ores and other materials.

Jan 1, 1998

By I. Casasbuenas, K. A. Nguyen, E. I. Ngoma, H. Kim, D. Borja, J. H. Park, R. A. Silva, S. Choi

"This study aimed to determine the optimum operating parameters of a continuous bioleaching system to leach arsenic (As) from mine tailings using a mixed mesophilic bacterial culture. The microbial consortium, previously adapted for effective growth at high pulp density and metal concentrations, was mainly composed of Leptospirillum ferriphilum, and Acidithiobacillus caldus. The mine tailings, collected from the Janggun mine (South Korea) contained 11% (w/w) of As. The tests were performed in a laboratory-scale unit composed of three reactors connected in series following a cascade configuration. Agitation speed, air supply, solid concentration, residence time and temperature were systematically optimized by assessing the leaching activity. Several parameters were monitored on a daily basis, including the As released into solution, iron oxidation rates, pH, cell concentration, dissolved oxygen and redox potential. Overall, improvement of oxygen transfer, by optimizing the agitation speed and air supply, presented the most tangible impact on the leaching performance. The highest As leaching efficiency observed in this study was 82%, which supports the feasibility of the process. INTRODUCTION Worldwide, around of 65 billion tons of mine tailings are produced every year (Jones & Boger, 2012). These materials comprise the waste minerals produced after ore beneficiation. Mine tailings usually contain heavy metals (e.g., Cobalt (Co), Lead (Pb), Zinc (Zn) and Arsenic (As) (Falagán, Grail, & Johnson, 2016; Nguyen, Lee, Park, & Lee, 2014). The exposure of these materials to the environment can produce serious health damage and environmental degradation (Martin, Dowling, Pearce, Sillitoe, & Florentine, 2014). Mine tailings management represents a major issue in South Korea. There are more than 1,000 abandoned mines containing stockpiled mine tailings within the territory (Choi, Park, Hong, Park, & Kim, 2013; Kim, Kim, Ahn, Ko, & Lee, 2005; Lee, Lee, & Kim, 1998). These tailings comprise high concentration of arsenic. Therefore, the Korean Government has directed its efforts to developing eco-friendly technologies, for the arsenic detoxification of mine tailings Continuous bioleaching is explored as a remediation technology (Borja et al., 2016). The present study aimed to develop a mixed mesophilic bacterial culture for optimal growth at high metal and solid concentration; and optimize the operating conditions of a continuous bioleaching unit. This investigation forms part of a larger study aimed to develop a bioleaching technique to treat Janggun mine tailings (Borja et al., 2017; Ngoma et al., 2017)."

Jan 1, 2018

By Michael Brittan

The Delkor Linear Screen represents an important screening innovation in the minerals industry. Applications geared to the enhancement of gold processing efficiency through coarse screening are presented. Recent developments in the use of the Linear Screen as a fine screening classification device in mill circuits are also discussed.

Jan 1, 1998

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

The Mining Foundation of the Southwest (MFSW), located in Tucson, AZ, will hold its 16th annual American Mining Hall of Fame Awards Banquet Saturday, Dec. 5,1998. The Hall of Fame recognizes outstanding contributions to the mining industry by selected individuals and industry partners. Each year, one living award recipient and up to two mining history honorees are chosen by the , Hall of Fame Committee and the Board of Governors of the Mining Foundation. In 1989, the Mining Foundation initiated a Medal of Merit to recognize outstanding individual, technical and professional contributions to the mineral industry. In 1995, an award was created to recognize contributions made by companies and organizations in partnership with the mining industry. This year's inductee, guest of honor and featured speaker will be Charles G. Preble, president and chief executive officer of Southern Peru Copper Corp. He is being recognized for outstanding performance as an executive of an American company operating under difficult circumstances in a foreign country. The Hall of Fame will induct H. Myles Jacob, former chairman and CEO of Inspiration Copper Co., for innovation and farsightedness in matters pivotal to the cop- per industry of his time. In addition, John Cromwell Lincoln, former president and chairman of Bagdad Mining Co., will be inducted for his outstanding contributions to the American mining industry. These contributions include metallurgical research and development of the Bagdad Mine as well as pioneering innovation in the electrical industry. Medals of Merit will be awarded to David N. Skillings, editor and publisher of Skillings Mining Re- view, for his dedication and support of mining interests. J. Ruben Velasco Rodriguez will also receive a Medal of Merit. He is economic geologist, professor and former secretary of the board of directors and secretary general of Compania Minera de Cananea. His medal is for fostering excellent relations between Mexico and the , United States in mining geology and management and for advancing the professional development of others in the field of earth science. An Industry Partnership Award will be presented to Stephen Bechtel and the Bechtel Corp. in recognition of Bechtel's 100th anniversary and the company's outstanding service to the mining industry. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest 520-577-7519, fax 520-577-7073.

Jan 1, 1998

By J. P. Mogan

As diesel exhaust contains a mixture of several materials of varying degrees of toxicity which interact to a currently undefined extent in their effects on health, the prescription of a quantity of ventilating air to dilute the exhaust to a safe level is necessarily, to some extent, arbitrary. Some jurisdictions rely on the application of a safety factor to a single "governing" component (usually nitric oxide for most modern diesel engines). Others specify that the total of the "adjusted" concentrations (actual concentration divided by maximum permissible concentration) not exceed "one" for related constituents (irritant gases for example). Neither of these approaches, however, takes account of the interaction of the gaseous constituents with diesel soot (although many studies verify such interactions), nor do they provide any economic incentive for reducing pollutants which are not included in the criteria for ventilation. Because of these factors, the Canadian Department of Energy, Mines and Resources awarded a contract for a study of the current literature bearing on the "Health Implications of Exposure of Underground Mine Workers to Diesel Exhaust Emissions" (1). One goal of this study was the formulation of a new ventilation criterion. The contractors, Ian W. French and Associates, studied more than 1500 literature citations which they interpreted in a 350 page report and summarized in a companion 1600 page annotated bibliography. In the recommendations section of the report, they defined a new 'health effects index' or ventilation criterion "V" as follows: [ ] The contractors consider that a "V" between 3.0 and 4.0 poses a moderate threat to health which could be alleviated by the use of protective equipment such-as filter helmets. If V exceeds 4.0, an increase in ventilation quantity to reduce the pollutant levels is indicated. In the case of mines with a quartz content in excess of 20% in the ore, the contractor recommends that a term. [Quartz]/ [Threshold Limit Value Quartz] be added to the equation, and [2.0 = ?v? = 30] be the range justifying protective equipment, with added ventilation if "v" exceeds 3. A degree of pragmatism was inherent in the development of the equation, as the contractors recognized that the components of the index, if it is to be useful in the near term, should be within current routine underground environmental assay capability.

Jan 1, 1980

By Francesco Chiappalone, Daniele Nebbia, Lance Waddell, Greg Colzani

As part of the 3RPORT Project, a 5-mile tunnel is being excavated underneath the three rivers of Fort Wayne using a 19-foot diameter Slurry Tunnel Boring Machine. The groundwater pressure at the tunnel axis ranges from 4.5 to 5.3 bar. The rock mass hydraulic conductivity is very high with water inflows up to 10,000gpm imposing significant challenges to the project. After excavating 1,550-feet of the TBM tunnel, major leaks between the tailskin and the segmental lining were observed, indicating the potential deterioration of the tailskin brushes and the need for inspection and eventual replacement. The first part of the paper describes the planning of the intervention, including the design of the polyurethane grouting campaign, the procedures developed for the execution and the controls established during construction to timely assess the presence of potential hazards. The second part of the paper focuses on the experience gained during execution and lesson learned to prevent future occurrences of this nature.

Jun 13, 2021

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By John E. Butler

Due to the present economic climate, particularly the depressed copper market, conventional mining, milling and flotation operations have been suspended. However, due to the apparent amenability of the ore to 'natural' leaching, investigations have been initiated into establishing an in-situ leaching operation as a preferred alternative to conventional operations. Cement copper production has been developed in parallel with the leaching trials and is presently at the rate of approximately 3,000 tonnes of contained copper per annum. Testwork includes controlled leaching of ore both in the laboratory and in-situ following blasting.

Jan 1, 1981

By Gregg J. Hodges

The Stillwater pt-pd mine and flotation mill are located about 130 km (80 miles) southwest of Billings in Stillwater county, M6ntana~ The pt-pd ore zone stretches about 43 km (27 miles), but varies in thickness from 0 to 6 meters (0 to 20 feet, but generally 3-6 feet) and dips 55-90,degrees from horizontal. The ore is hosted in basic, layered igneous rocks containing about 1% sulfide minerals which include chalcopyrite, pentlandite, pyrrhotite, and minor pyrite. The pt-Pd minerals are intimately associated with these sulfide minerals and are found as precious metal sulfides, tellurides, bismuthnides, and arsenides as well as native Pt metal. Approximately 90 different precious metal minerals have been found, but about 80% of the pd is in solid solution in the pentlandite. The ore assays about 0.1% Cu, 0.1% Ni, 6.2 g Pt/tonne (0.18 Troy ounce Pt/short ton (opt)), 21.3 g Pd/tonne (0.62 opt Pd), 0.21 g Au/tonne (0.006 opt Au), and 0.21 g Rh/tonne (0.006 opt Rh). The ratio of pd to Pt in the Stillwater ore and concentrates is about 3.5.

Jan 1, 1988

By Jim Johnson

The purpose of this paper is to summarize and discuss a variety of site specific conditions which are typically evaluated as part of the engineering design process for heap leach pads, solution control ponds, and associated facilities. The following sections will focus primarily on the topographic, climatologic, hydrologic, and geotechnical evaluations critical to selection of heap leach sites, and selection of a preferred heap leach configuration or method. Other important considerations in the design of a heap leach project, including evaluation of ore properties and leachability, pregnant solution processing requirements, spent ore neutralization/disposal requirements, and other anticipated reclamation requirements are beyond the scope of this paper are not addressed in any detail.

Jan 1, 1998

By Dale Brunton, Robert Adams, Michael Dutton

Tunnels and other underground structures are typically designed using ground-structure interaction models instead of traditional structural analysis programs. This allows for the degree of load sharing etween the two odies to e calculated allowing for a more efcient design. hile modern codes outline the use of limit states with factors on applied actions, limit states are not typically compatible with ground-structure interaction models. Consequently, the engineer is left to develop rational methods for incorporating load factors into their analyses. Several methods can be considered, including the Largest Factor Method, Averaging Method, Subtraction Method, and Split Factor Method. This paper discusses the approaches, compares their effects using a case example, and provides a recommendation for designers.

Jun 23, 2024

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Paul Eimon

The 1981 Fall field trip of the Denver Region Exploration Geologists' Society focuses on Creede. That is appropriate - because significant mining history has been made and is being made in this off-the-beaten track, high-country mining district. Creede is one of the few Colorado bonanza towns which was big in the 19th Century, had its ups and downs, and produced almost continuously since its discovery. Creede is important to geologists for its: precious and base metal production, current exploration activity, and research into near-surface hydrothermal systems. United States Geological Survey research and field geologists zeroed in on Creede some 25 years ago and their steady, consistent work is now being spotlighted and appreciated.

Jan 1, 1981

By PDF

Previous work has shown that significant, free milling gold values exist in the Ryan Lode ore. This project used pilot scale equipment to estimate the percentage of gold recoverable by gravity methods from the circulating load of a conventional, closed-circuit, grinding mill. The pilot scale flowsheet employed three stages of gravity concentration, hydraulic classification and batch grinding to simulate a full scale milling circuit. 172 kg (379 lbs) of Ryan Lode ore were processed, having a head grade of 4.8 g/metric ton (0.14 oz/ton). Results showed that simple gravity methods are capable of recovering 45-50% of the gold values in a concentrate grading in excess of 3430 g/metric ton (100 oz/ton). Of the remaining gold values reporting to the classifier overflow solids (80% passing 70 microns, 3.1 g/metric ton (0.09 oz/ton)) 89% were recovered from 48 hour bottle roll tests.

Jan 1, 1995

By Alexander N. Winchell

"The iron ores of the Lake Superior region are found almost exclusively in rocks of Huronian age, the only exception of importance being in the Vermilion district. It may be estimated that about 95 per cent of the ores thus far mined have been obtained from Huronian rocks. Although these ores come from rocks of varying age and slightly varying type, they have many features in common, and therefore may readily be described together.The iron formations of the Lake Superior region consist essentially of interbanded layers of mixtures in widely varying proportions of silica and iron oxide, and are called taconite, ferruginous chert, or jaspilite. They vary considerably in hard¬ness and color, depending upon the tenor of silica and the history of the rock. Local phases of the iron bearing formation consist of cherty iron carbonates, greenalite or ferrous silicate, rocks, amphibole-magnetite masses, cherts and slates, and pyritic quartz rocks. The average iron content of all the original phases of the iron bearing formations, excluding interbedded slates, is about 25 per cent, while the average iron content for all portions of the formation, whether in the original condition or not, is about 38 per cent. It is believed that this difference is due essen¬tially to the removal of silica in solution from the. primary phases, and, of course, such removal of silica has in many cases produced material now used as iron ore, since it contains con¬siderably more than 38 per cent of iron."

Jan 1, 1920

By R. A. Metz, James W. Clark, William C. Dixon, Kevin L. Wiley, Thomas R. Couzens

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1992

By Corneille S. Ek

Flotation of several copper and lead-zinc ores has been carried out with mercaptobenzothiazole (MBT) as promoter. The results of laboratgory batch flotation tests have been compared with those obtained when using more common collectors like xanthates or dithiophosphates. It generally appears that MBT is an effective collector of all the sulfides, including pyrite, but that high selectivity is rather difficult to attain, except for gangue drop-out. Some kinetic tests have been performed to check the froth production rate by MBT as compared to other collectors.

Jan 1, 1995