Search Documents

By G. C. Anderson

The Cleveland Cliffs NOLA electronics and software upgrade is a Windows based system that simultaneously controls two Texas Nuclear NOLAs and associated sampling. It uses new spectrum analysis and algorithms to produce accurate, linear silica measurement with slurries that range from 5 through 50 percent solids. This linearity allows us to achieve a reproducible procedural calibration. The hardware consists of readily available shelf items, is extremely redundant and eliminates all NIM bus modules.

Jan 1, 2003

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0-5 to 2.9 Pb CaS/lb Kg in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1983

By E. Lefeuvre

Precambien in age, the phospate deposit under study which outcrops to the south forms a synclinal consisting of only one mineralized horizon. The synclinal strikes SSW/NNE, dips from 30 to 60 NNE and is about 5 km wide. The deposit has been explored by : - trenches and pits about 50 m apart in the outcropping area ; - core drill holes forming lines perpendicular to the outcrop. These lines are about 100 m apart. On each line, the drill holes are about 50 m apart The phosphate layer is clearly visible and has then been defined from the geologicia1 description of drill hole logs. The layer has been divided into two parts : a very rich, altered part at the hanging wall and a poor part displaying opposite physical characteristics, i.e. a fresh and hard rock. With open pit mining in view, the deposit has been divided into a 3-dimension network of blocks, each block measuring 50 X 50 X 100 m. The tonnages of rich and poor ore, PO25, MgO, Si02, CaO and R2O3 grades and the tonnages of barren waste at the hanging wall and the footwall have been calculated for each block. Given the dip of the phosphate layer ranging from 30 to 60° and its relative thickness (between 10 and 15 m), it was impossible or inappropriate to carry out direct calculation by 3-dimension kriging : too many neighboring blocks to obtain sufficient date and impossibility to draw up the morphology of the layer.

Jan 1, 1986

By Paul R. Thomas

This paper addresses the long-term cost and availability of primary gold production from the Republic of South Africa. Forty-four major producing or developing operations were evaluated. The analyses present estimates concerning 1) total refined gold potentially available from demonstrated resources, 2) annual production potential into the next century, 3) long-term weighted average total costs for underground mine production and surface waste reprocessing, 4) the expected annual decrease in gold production, and 5) the ability of other market economy countries to compensate for the anticipated decline in South African gold output. This paper draws upon the data and analyses of a recent Bureau of Mines, U.S. Department of the Interior, Minerals Availability Program appraisal that evaluated the worldwide availability of gold and silver from primary precious metal operations and as a byproduct of base metal production.

Jan 1, 1984

By S. Bastola

Over 80% of roof falls in Illinois coal mines occur at intersections. Regular intersection geometries with sharp corners have been typically analyzed in literature. This study has analyzed stress distribution around typical field 4-way intersection geometry and compared it with similar data for regular four-way intersection geometry. These analyses were performed using 3-D numerical analyses for a typical lithology associated with No 6 coal seam in southern Illinois. Linear elastic and non-linear analyses, using Hoek-Brown failure criteria for different lithological units, were performed. The 3-D models incorporated bedding planes and pre-mining horizontal stresses. Effect of diagonal widths of the intersection and pre-mining horizontal stresses were examined due to their influence on stability. In addition to stress distribution, contours of safety factors, and displacement analyses were performed to assess stability of intersections.

Feb 27, 2013

By Sara J. Heinlein, George Malkos, James E. Lindell, Tony Pestonatto

The 79th Street Water Tunnel Extension Project was initially designed by the City of Chicago, Department of Public Works, to increase the capacity of the City’s south side water distribution system. MWH preformed a design review, prepared the final design and provided construction management for the City of Chicago Department of Water. Construction commenced in September 1995 and was completed in October 1999. The Project connected two existing water tunnels with a new 5.8 km (19,044 ft.) long, 4.9 m (16.08 ft.) finished diameter concrete lined rock tunnel utilizing TBM, drill-blast and mechanical hoe-ramming methods. In addition, approximately 61 meters(200 feet) of concrete lined variable cross section tunnel, a new gate shaft and a temporary construction shaft were constructed. This paper describes the construction of these features and the geological conditions encountered.

Jan 1, 2003

By E. V. Bowman

This paper is intended to deal with the material handling aspects of fine coal cleaning as applied to a recently built plaint in: southern West Virginia. This plant is processing 160 tons per hour of 1/4" x.0 coal on a two shift basis. Past experience with this very friable low volatile metallurgical coal indicated that its plastometer readings, varied directly with the size and length of time elapsing between mining' and ultimate consumption. Due to the mines location with, respect to its consumers, little could be done to decrease the time element. Studies indicated that the plastometer readings are considerably less in the minus 60 mesh range than that experienced in the plus 60 mesh sizes. Therefore, handling the coal in such a manner as to have the least amount of degradation became extremely important.

Jan 1, 1961

By H. Walqui, A. Buendía

The Toquepala concentrator expansion project incremented the capacity of the existing concentrator by 15,000 Metric tons per day (t/d), from 45,000 to 60,000 t/d. The plant is located in southern Peru,1,200 km southeast of Lima. The implementation plan for the expansion project was based upon an engineering and procurement contract, and a construction contract. The overall Project Management was by Southern Peru Copper Corporation (SPCC). The expansion followed a very aggressive schedule that considered a construction period of only ten months, with minimum interference to the existing facilities. Major equipment was purchased during basic engineering. This paper details the design, construction, and commissioning of the 6.4 m diameter by 10.2 m long ball mill, and the performance of the milling circuit during the first two months of operation.

Jan 1, 2003

By D. F. Symonds

INTRODUCTION Dense medium processes have been used to separate coal and ores for over a hundred years. In fact Sir Henry Bessemer first patented a process in 1858. In recent years, their importance relative to other gravity dependent processes has increased. This is particularly true in the coal industry where over 60% of all preparation plants operating in 1984 in North America (1) contained either dense medium vessel or cyclone circuits. In addition, the stringent product quality demands of the consumer, together with increases in mining costs, dictate that the cleaning circuits be both predictable and efficient. Dense medium systems are the most predictable and efficient of all gravity- dependent processes. The majority of the text of this chapter will be concerned with dense medium applications as they relate to the coal industry. However, the techniques and calculation procedures can be applied, in general, to all non-coal minerals (such as diamonds, marginal iron and lead-zinc ores and gravel) which take advantage of a difference in specific gravity between the saleable product and the reject. The object in dense medium cleaning is to produce a liquid whose effective specific gravity is between that of the concentrate and the reject. In which case the lighter product will float to the surface and the heavier product will sink to the bottom. Unfortunately, this simple process becomes complicated by the following practical necessities: (a) collecting and removing the float and sink products from the medium without disturbing the free settling effects; (b) maintaining and controlling the specific gravity of the medium; (c) separating and reclaiming the medium once the products have left the separating vessel; and (d) separating finer sized particles which take longer to fall through the dense, and often viscous, medium. As a result of the last issue (item d) two main types of dense medium separators have evolved: dense medium vessels and dense medium cyclones. Dense medium vessels are essentially large baths through which the dense medium flows at a relatively slow velocity. The lighter products float to the surface and are carried out of the vessel by the medium flow. The heavier products sink to the bottom of the vessel and are physically transported out either by means of a conveyor (usually a chain conveyor) or a rotating, lifting arrangement (Figure 1). They generally

Jan 1, 1986

By P. D. Rao, D. E. Walsh, W. W. McClintock

A column flotation system was designed to conduct release analyses on a very finely disseminated, stratiform copper ore from the Denali Copper Prospect in Alaska. Chalcopyrite is finely disseminated in a carbonate matrix, and pyrite is disseminated in both the chalcopyrite and the gangue. Grinding to -20 µm is required for adequate liberation. A 25-mm x 2.4-m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate. The rougher concentrate was then repeatedly floated to produce release fractions. These fractions were analyzed for copper, iron, calcium and magnesium, and release curves were plotted. The procedure was replicated at each of two grinds, i.e., 99% and 88% passing 37 µm (400 mesh). The procedure should find application for flotation characterization and process selection. Bond grindability testing was also conducted.

Jan 1, 1996

By R. J. Hickson

From 1993 through 1999, Cyprus Amax Minerals successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized and an environmental issue was appropriately remediated. The projects stretched over three continents: from arctic Russia to the Atacama Desert, from sea level to an elevation of 4,900 m (16,00Oft), from city suburbs to remote wilderness and from a low of US$130 million to more than US$ 1billion. The operations included open-pit and underground mines, mill and leach facilities and involved gold, copper, molybdenum and coal. The diversity of these projects inspired Cyprus Amax to create a "best-practices” project-management protocol to steer corporate expansion in the new millennium. This paper summarizes these best practices, while highlighting the project-management pirfalls to avoid.

Jan 1, 2000

By Z. F. Wang, W. K. Choi, A. E. Torma

The present study has investigated the bioleachability of low-grade and high-grade pyritic gold ores and the extraction of gold from the leach residues of bioleaching with thiourea solutions. Final gold extractions as high as 96% were obtained from the high-grade ore and above 93% from the low-grade ore. The gold extraction was found to follow the extent of pyrite biooxidation. Using a cyclic voltammetric technique and carbon-paste-FeS2 electrode it was found that the semiconductor pyrite oxidation involves many intermediate electrochemical reactions. Furthermore, the oxidation is solid-state diffusion controlled as suggested by chronoamperometric and chronopotentiometric measurements.Using Sand's approach, the activation energy of solid-state diffusion biooxidation of pyrite was determined to be AEa=22.4 kJ. A generalized model for the mechanisms of pyrite oxidation has been presented.

Jan 1, 1990

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By Wen L. Cai

This paper examines the effects of different block dimensions and cone bases on the economic open pit limit design based on case studies on a coal deposit consisted of two west- east elongated, near vertical thin seams starting with a base model dimension of 200x170x50 (NX*NY*NZ) with a block dimension of 10mx5mx4m (DX*DY*DZ), the blocks were combined along easting, northing and elevation directions. Two cone bases were used, one with a base radius of 10 meters, the other with a base radius of 0. Two pit design algorithms, one is the floating cone algorithm, the other is an optimum algorithm, were used to see which one of the two pit design algorithms is more sensitive to block dimension and cone base variations. The results are presented and analyzed.

Jan 1, 1992

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976