Search Documents

By Dan Plazak

Discussion by Dan Plazak The authors are to be congratulated for presenting a simple and practical tool for quick estimates of ground water flow rates. At the risk of detracting from the simplicity of the method, I would like to suggest a slight refinement to the equation as presented. As the authors noted, the Jacob-Lohman equation (1952) assumes confined-aquifer conditions. To use confined-aquifer equations in water-table aquifers, Jacob (1963) presented a correction to convert water-table aquifer drawdowns [Ahw] to equivalent confined aquifer drawdowns [Ah,: 2] [Ah Ah = Ah - w(1) Cw 2H where: Ah, = Drawdown in confined aquifer: Ahw = Drawdown in water-table aquifer and H = Original saturated thickness of aquifer] Substituting the above in equation ( I) of Hanna. Azrag and Atkinson [4nT Ah - 2H ) Qj2.25 T t(2) 1 nr2 S W] Since the above expression predicts lower pump rates, it causes the Jacob-Lohman equation to agree more closely with appropriate analytical and numerical models. Figure 1, adapted from Fig. 5 of Hanna. Azrag and Atkinson, illustrates the closer agreement of the modified equation to their numerical model, as reflected in Qm/QJL ratios closer to unity. The agreement improves particularly as drawdown [Ah] becomes large in relation to aquifer thickness H. An additional advantage of the modified equation is that Hanna, Azrag and Atkinson's correction factor C is much more stable as pit depth increases. Assuming, as did Hanna, Azrag and Atkinson, that their numerical model is an accurate predictor, it is clear that the modification incorporated in equation (2) improves the accuracy of preliminary estimates of ground water flow to a pit.[ ] References Jacob, C.E and Lohman. S. W.. 1952, "Nonsteady flow to a well of constant drawdown in an extensive aquifer." Transactions, American Geophysical Union. Vol, 33, No. 4. pp. 559-569. Jacob. C. E.. 1963, `Determining the permeability of water-table aquifers,' USGS Water-Supply Paper 1536-1, pp. 245-271

Jan 1, 1995

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By Al. Valero, A. Domínguez

This paper appraises the energy requirements for mineral production through an exergy approach taking into account the long-term decline in ore grades. In this context, the exergy required for restoring resources from the dispersed state of the so called Crepuscular Earth into the physical and chemical conditions in which it was delivered by the ecosystems in light of the available technology, is known as exergy cost. The exergy cost is the point of reference in order to evaluate in a single variable, characteristics such as composition, concentration (ore grade) and the state of technology. The ratio between the exergy cost and the minimum thermodynamic cost required to accomplish the same process is called unit exergy cost and provides a measure of the irreversibility of the analyzed processes. Otherwise, the ore grade is one of the main issues which affects directly the costs associated with mining the ore. Hence, the unit exergy costs to produce minerals from progressively lower ores grades by the current technology is analyzed. The unit exergy cost curves are presented for some important minerals such as aluminium, chromium, cobalt, copper, gold, lead, manganese, nickel and zinc, in order to know the trend when the ore grade decreases.

Jan 1, 2011

By D. S. Bloswick

An investigation an4 analysis of slip/fall accidents specifically pertaining to underground coal mines was conducted. From a population of 751 accident reports, three major sources of injury which account for over 80% of the incidents have been identified. The specifics of this study are presented in this paper. Based on the results, several recommendations are made to reduce such accidents in underground mines. In addition, a brief discussion of the slip-hazard analysis laboratory at the University of Utah, which will be useful in future analyses of these accidents is presented. Work in this facility includes the simulation of certain mining activities in a controlled setting. Foot forces are measured and work methods subsequently developed to minimize the slip potential of these activities.

Jan 1, 1988

By Wallace W. Wilson

It scarcely 1s possible to read a new issue of any of the principal mining trade journals without noting some mention of a major new overseas mining venture with which one or more domestic companies are involved. These projects seem to follow a fairly consistant pattern; most are large open pit mines, with relatively low grade ore bodies but huge reserves; the total price tag will be in nine significant figures and around half or more of the total cost will be for infrastructure. West1 noted that nearly $7 billion is being invested annually for new mining projects and the expansion of existing mining ventures, in the free world. He anticipates that by the year 1975 such investments would reach the $10-11 billion annual figure, and that in the five year period 1972-76 total capital requirements can be expected to aggregate around $45 billion. The proportion of this total investment which will be financed in some manner is difficult to estimate because of the variety of available financing arrangements. West estimated that around 75% of the total capital would come from internally generated funds, with the balance from external sources. Conceivably a substantially higher percentage could be attributable to external financing, especially it the trend of recent mineral development in Canada and Australia is any criterion, and of course, including local sales of equity as a part of the package.

Jan 1, 1973

By Roger Holmberg

INTRODUCTION The driving of drifts is a very important aspect of underground mining. It is not unusual for the percent¬age of rock broken during development in a mine using sublevel caving, for example, to be as much as 25% of the total. If one also considers the amount broken for transport, ventilation, and exploration drifts, one can easily understand that the planning and excavation of drifts play a major part in the total economics of the mine (Fig. 1). Increasing mechanization in mining demands larger tunnel areas for transport and mining equipment. With modern machines the hard work involved in using hand¬held pushers is gone, and a better environment is achieved. More rational methods could be used, but much of the experience the working man acquired by working close to the rock face (such as utilizing the natural weak planes in the rock when he placed the drill¬ing holes) has unfortunately been lost. By having sepa¬rate shifts for drilling, loading, and hauling, more atten¬tion has to be placed upon a well-designed drilling pattern. Some reduction in the number of holes required can be achieved with mechanized drilling because of the larger holes that can be produced. On the other hand, it is probably not possible to achieve the same precision as with pneumatic pushers, and it is difficult to utilize the larger holes because these cause more damage to the re¬maining rock. Recently, however, the precision has be¬come very good with the parallel booms and automatic devices for setting the lookout angle (Fig. 2). A larger arch of the drift roof requires a more carefully executed blasting procedure than before in order to prevent rock fall and to insure a sufficiently long stand-up time. In this chapter, empirical relationships that can be used to design an economic and optimal drift blasting design will be presented. The principles of the calcula¬tion method are based upon the earlier work of Langefors and Kihlström (1963) and Gustafsson (1973). COMPARISON OF EXPLOSIVES To provide for the use of various explosives it is necessary to have a basis of comparison. Several meth¬ods have been developed to characterize the strength of an explosive. Some examples are comparison of values given by (1) calculated explosion energies; (2) the ballistic mortar test; (3) the Trauzl lead block test; (4) the brisance test; (5) the weight strength concept; and (6) the underwater test. However, most of these meth¬ods should be used carefully when stating the breaking

Jan 1, 1982

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By J. Villeneuve, M. A. Reute, E. Verhoe

The objective of EU waste policy is to reintroduce used materials into the economic cycle, especially by recycling, or to return them to the environment in a useful state or at least a harmless state. To support decision-making in complex systems, the standardised ISO 14040 life cycle assessment (LCA) method can be used to quantify and to interpret the environmental repercussions of (changes in) a product system from cradle to crave related to a functional service unit. The use of the standardised LCA method at European level can be characterised as a damage-oriented or top-down method, which is often used in product design. Winning, extraction and processing of metals are part of the interconnected worldwide metals production system linked to product design, manufacture and recycling. This complexity cannot be dealt with using LCA. This paper will discuss a dynamic model that deals with this complexity, at the same time providing detailed bottom-up insight into the complex web of materials referred to as Metal Ecology. An example on the replacement on lead in solders will be discussed to illustrate this.

Jan 1, 2005

By David J. Akers

INTRODUCTION The variety of uses of coal and the wide range of characteristics of coal combine to produce a need for a wide variety of laboratory analysis. Coal is used to heat homes, produce electricity, and make coke for steel manufacture. It can also be used to produce both gaseous and liquid fuels as well as a variety of chemical products. Various applications may require specialized analytical procedures. For example, some of the procedures developed for the coke industry, such as expansion or contraction during carbonization, have little value to the power generation industry. Even for a single application, the type of analysis needed can depend on the source and/or general nature of the coal. This section provides a general overview of the types of analytical procedures commonly applied to coal from the perspective of the user of this information, not the producer. The intent is not to detail laboratory procedures, but rather to discuss the application of commonly used laboratory tests in coal preparation. Accordingly, laboratory procedures are categorized by type of information produced. Gravimetric Analysis Procedures that produce weight-based information (parts per million, pounds per cubic foot, or weight percent). Such analyses can relate to the coal's physical, chemical, or mineralogical characteristics. Volumetric Analysis Procedures that produce volume-based information (amount of a mineral present as a volume percent). The primary source of volumetric information is from petrographic analysis. Application Tests Procedures that measure some characteristic of coal that has been empirically related to some application or handling or processing step. Typically, these procedures attempt to duplicate some aspect of the commercial application at laboratory scale and may produce information in the form of an index. Applications procedures do not measure a single component of the coal but infer the combined effect of multiple components. Each class of information is discussed in the order listed. References are provided as a source of more detailed information. The American Society for Testing and Materials (ASTM) publishes the most inclusive reference to analytical procedures. This publication,16 which is revised annually, provides extensive information concerning generally accepted methods of laboratory analysis. ASTM also provides standards for sampling and some information concerning sample handling.

Jan 1, 1991

By Ricardo Gomez, C. T. Ogryzlo, A. A. Dor

This paper reviews the historical background leading to the development of the project. It gives a description of the exploration program and resulting geological and ore reserve information together with plans for mining. A discussion is included of the three processes investigated for the project: 1. Rotary Hearth and Magnetic Concentration 2. Shaft Furnace and Electric Furnace 3. Rotary Kiln and Electric Furnace Results of pilot plant campaigns conducted at Fiskaa, Norway, and Riddle, Oregon, on the process chosen for the production of ferronickel are presented. The paper continues with a review of the considerations involved in selection of commercial plant equipment and concludes with comments on the current status of the project.

Jan 1, 1979

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By C. S. Thompson, P. A. Ciullo

Pyrophyllite is a naturally occurring hydrous aluminum silicate with the molecular formula SiO,,AI,,(OH), or, as more commonly expressed, the oxide formula A120,~4Si02~H20. Pyrophyllite is rarely found in deposits as the pure mineral and is often intimately associated with quartz, sericite, kaolinite, and diaspore. These associated minerals, to a large degree, help determine the most appropriate commercial application for a given pyrophyllite ore. Structural similarities plus the generally soft platy nature of pyrophyllite has in the past caused it to be included with talc in applications and production data. The Minerals Yearbook, published annually by the US Bureau of Mines (USBM), still reports on talc and pyrophyllite together, although admitting that they do not share the same uses. Pyrophyllite has also at times been considered a clay mineral because of its structure and chemistry. The refractory properties of pyrophyllite have been known for nearly 200 years, but it has only been in the past 60 to 70 years that a variety of applications have been developed to exploit the unique characteristics of this mineral. Worldwide, pyrophyllite is a component of refractories, whiteware, foundry mold dressings, pesticides, paint, plastics, rubber, cement, fiberglass, and soap. Historical Overview The most salient refractory features of pyrophyllite are its low coefficient of thermal expansion, high thermal conductivity, low moisture expansion, and good resistance to corrosion by molten metals and basic slags. One of the first recorded uses of this mineral was as firebrick in Japan in the early 1800s. This followed its discovery in 1797 on Mount Omotoyama at the site of the present Mitsuishi mine. In addition to firebrick, sawn blocks of ore were used for carvings and in the manufacture of slate pencils and signature seals. The Mitsuishi mine is still one of Japan's largest. By the mid-1800s, refractories were being made in Japan from roseki (a pyrophyllite-bearing ore) for the construction of metal melting furnaces. The mineral did not get its name until 1829 when R. Herman, testing a sample of supposed talc from the gold-quartz veins at the Berezovo deposit in the Urals, showed that it was actually an aluminum silicate and designated it pyrophyllite. This name was derived from the Greek pur for fue and phullon for leaf, in allusion to the effect of heat in causing separation of the laminae in foliated varieties (Mellor, 1927). The exact date of the discovery of pyrophyllite in the United States is uncertain, but it is believed that the talc and soapstone deposits noted in an 1827 report on the geology of the slate belt of North Carolina were actually pyrophyllite occurrences (Olmstead, 1827). Pyrophyllite was first used in North Carolina on a local basis in the early 1800s. Blocks were sawn and cut for use as stove linings, mantels, chimneys, fireplaces, and gravestones. This was the material of choice because it did not shrink when heated, but cut easily and hardened as it weathered. Pyrophyllite crayons were sold commercially by local gold miners for steel marking and as tailor's chalk from about 1800 until 1922. It was during this period that pyrophyllite was discovered near the town of Hemp (later renamed Robbins), NC. The large quantity of scrap resulting from the sawing of crayons at this deposit prompted the construction in 1921 of a grinding plant. The ore scrap was ground to fine granules and sold to asphalt producers to prevent shingles from sticking together. By the mid-1930s, milled pyrophyllite from North Carolina was also being successfully utilized by the ceramics industry in whiteware for its low cost and ability to shorten firing time. Also during the 1930s, pyrophyllite was first used in kilncar furniture in the United States. Canada was another early entrant in the pyrophyllite business. Mining at the Foxtrap deposit on the Avalon Peninsula of Newfoundland began in 1904, with ore shipped to the United States. Production from this deposit was mostly sporadic in the ensuing years until 1956 when mining began for shipment and captive use in US tile manufacture. This production has remained continuous and still essentially captive to the present. The Foxtrap deposit is currently the sole commercial source of pyrophyllite in Canada.

Jan 1, 1994

By D. E. Ranta, M. G. Hester

The ore reserve modelling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore-forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high-grade and low-grade drill hole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realtistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1992

By Scott Donald, Barry Esford

Cameco Corp. operates uranium mills and tailings management facilities at its Key Lake and Rabbit Lake operations in Northern Saskatchewan, Canada. Development at both mine sites began in the 1970s, with initial tailings deposition occurring within above-ground impoundments, which was common for these facilities at the time. As open pits became available at each site, and mining continued at other orebodies in the area, tailings management shifted to in-pit facilities to meet stakeholder expectations and improve the long-term security and environmental performance of tailings management at these facilities. The in-pit facility at Rabbit Lake (receiving tailings since 1984; Fig. 1), was one of the first (if not the first) engineered in-pit tailings facilities in the world and adopted a full pervious surround design concept with subaerial deposition. Under this concept, permeable sand and coarse rock are placed at the base of the pit, around its perimeter, as well as overlying the tailings at closure to promote regional groundwater flow bypassing the lower-permeability tailings. In contrast, at Key Lake, the in-pit facility (receiving tailings since 1996) adopted a partial pervious surround design concept. Under this concept, permeable materials were again placed at the base of the pit, and partway up the side walls; although for the upper portion of the tailings, the material is placed directly against the natural geologic materials. In the Key Lake case, the natural geologic environment provided the required bypassing of the tailings deposit to achieve the desired environmental performance while the base drain again facilitated pumping during operations to achieve consolidation objectives (Fig. 2). In both the initial design of the facilities, and through more than several decades of operation, it is clear that although in-pit tailings facilities provide common benefits with respect to long-term geotechnical stability, it is critical that their design approach take into consideration site-specific conditions

Jul 1, 2025

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By S. P. Taite, A. R. Charest, P. D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in southwestern Chihuahua State, Mexico. The prospect was discovered by a Francisco Gold Corp. geologist in1995. El Sauzal was encountered as a result of an extensive grass-root exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas Silver Camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiary age. The mineralization appears to be both structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system including kaolinite, illite, alunite, dickite and pyrophyllite. The deposit’s gold distribution, as recorded from drill-hole data and surface samples, varies from 0.2 to 650.0 g/t. The estimated geological resource, as calculated from an independent study completed in 1998, was 3.0 million oz @ 2.03 g/t including a minable reserve of1.8 million oz @ 3.3 g/t.

Jan 1, 2004

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986