Search Documents

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

Today, approximately 31% of underground coal mining operations have designated occupations or areas with more stringent (below 2.0 mg/m3) respirable dust standards in place. Many U.S. coal mines have been able to maintain compliance with very low dust levels, and the Bureau of Mines, in an effort to identify those factors contributing to low dust levels, completed a survey of twelve continuous miner sections which were able to maintain their dust levels at or below 0.5 mg/m3. The quantity and quality of face ventilation appeared to be the most important factor in controlling dust exposure. The results directed Bureau research towards identifying improved face ventilation techniques for reducing quartz dust levels on continuous mining operations. This research has involved the evaluation of a half-curtain face ventilation technique which reduces the cross-sectional area of the entry, thus increasing the air velocity over the operator. The Bureau has also conducted extensive laboratory studies to compare tubing versus brattice, including an evaluation of both systems in a crosscut turn. In an effort to improve ventilation and reduce dust exposures of roof bolter operators working downwind of the continuous mining machine, the Bureau has evaluated two novel face ventilation systems. The first system consists of a fan discharge tubing technique which routes dusty air away from the return entry being bolted. In a technique similar to the fan/tubing concept, exhaust air from the upwind continuous miner face can be scrubbed using a dust collector to capture a portion of the dusty air, clean it, and supply it to the bolter operators as a split of clean intake air. A better understanding of face ventilation techniques should lead to solutions to the problem of more stringent dust standards due to quartz.

Jan 1, 1989

By E. F. Divers, R. A. Jankowski

In response to a request from the Mine Safety and Health Administration (MSHA), the US Bureau of Mines completed a respirable dust survey of 18 US coal preparation plants. Of these, three were essentially free of dust problems. Respirable dust exposure to workers in the remaining plants depended on the time spent in the dusty areas. In five of the plants surveyed, Bureau tests showed that in some areas worker exposures could exceed Federal dust limits in less than two hours. Cooperative studies were arranged with coal preparation plants using three different dust control techniques. These included a standard baghouse-type dust collector, two types of scrubbers, and an electrostatic precipitator. Results of these evaluations are presented. Various types of ventilation systems used during summer and winter conditions were also evaluated. Results showed that appropriate ventilation can provide a highly cost-effective method for controlling coal preparation plant dust.

Jan 1, 1987

By Stephen H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, New Mexico area. The first four shafts sunk at international Minerals and Chemical Corporation's property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 Shaft there has been extensive-erosion and salt dissolution in the Rustler Formation which has led to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows it was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be codified to reflect any new or additional information which is obtained during the progress of the grouting.

Jan 1, 1984

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By Elif Emil-Kaya

Samarium (Sm), as one of the rare earth elements (REEs), has gained significant attention in the production of samarium- cobalt (SmCo) magnets due to their high corrosion and oxidation resistance, as well as their high-temperature stability. SmCo magnets find applications in various industries, including but not limited to national defense, aerospace, military and medical equipment. Sm and Co have been classified as critical metals due to their economic importance and supply risk. Recovering Sm from SmCo magnets is an effective method to ensure a stable supply. The present study investigates an integrated hydrometallurgical treatment and combustion process for the preparation of rare earth oxide (Sm2O3 ) powders from SmCo. Initially, SmCo powders are exposed to nitric acid, and the resulting slurry is selectively oxidized at 250 °C to obtain Sm(NO3)3 , Co2O3 and Fe2O3 . Subsequently, the selectively oxidized powders are leached with water to extract Sm. Sm2O3 powders are produced from the obtained leaching solution using an energy- and time-efficient solution combustion process. Finally, the optimal conditions for the production of Sm2O3 are identified, and the produced powder is characterized through X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis.

Nov 1, 2024

By T. J. Smolik

The Golden Sunlight Mine started full-scale operations in February 1983, with a conventional open-pit mine supplying 4464 tonnes (5000 tons) per day of milling ore. After crushing and grinding, the ore is leached with cyanide solution in large agitation tanks. Soluble gold values are removed from the sand portion of the leached ore with five stages of countercurrent washing cyclones. After thickening of the cyclone-wash overflow slurry, the gold is recovered in activated carbon with a six-stage carbon-in-pulp circuit and a five-stage upflow carbon column circuit. Pressure stripping, carbon reactivation, electro-winning and refining complete the gold recovery process.

Jan 1, 1984

By Zhongxue Li, Baolu Zhou, Yiqing Zhao

"Rare earth elements (REEs) are a kind of new materials which have excellent optical, electrical and magnetic properties, and they play an important role in the development of high technology and green energy industries. With abundant reserves and a wide range of REE type, rare earth industry has a rapid development in China in recent years. However, environmental issues associated with REE exploitation have severely restricted the sustainable development of rare earth industry in China. At present, literatures on the externalities of REE exploitation are very limited, especially in China. This paper builds an evaluation model based on life cycle evaluation to estimate the external costs of REE exploitation at Bayan Obo. The results show that the external costs for producing one metric tonne of rare earth oxides (REO) in Bayan Obo was CNY 34739 in 2013, the external costs of waste gas, waste water, radioactive substance, REE resource depletion, and land occupation are CNY 14945, 12515, 1400, 3199, and 2680, respectively. Waste gas and water constitute about 79% of the total external costs. The internalization of the external costs would reduce the financial profit of Northern Rare Earth (Group) by 18%. This study has taken into account only those externalities whose market values can be estimated, and therefore the external costs of REE exploitation in Bayan Obo is likely to be underestimated. The results fill the gap in literature and provide further understanding on the external cost of REE exploitation.Introduction / Background Along with increasing concern about environmental pollution problems caused by the usage of fossil fuel and the shortage of fossil energy, a transition has occurred where development has moved toward green and renewable energy sources with less pollutant emissions (Stegen 2015). Rare earth elements (REE) are a group of important raw materials for these trends since they have unique magnetic, electronic and optical properties, and thus make them widely used in making high-performance magnets and energy saving lamps (U.S. DOE 2010). In addition, REE are crucial for manufacturing of widespread high-tech applications in medical, defense and electronic industries. Many countries have made medium-term and long-term plans for the development of their REE industries, and the annual growth rate of global REE demand is expected to increase by 6% by 2020, and reach about 170,000 metric tons of rare earth oxides (REO) by 2020 (Rollat et al 2016)."

Jan 1, 2017

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By G. C. Van Bever, J. J. Zaluski

Introduction The Surface Mining Control and Reclamation Act (Public Law 9587) (hereinafter the "Act" or "SMCRA") passed by Congress in August 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations. In 30 U.S.C. § 1272, Congress provided that "[a]ny person having an interest which is or may be adversely affected shall have the right to petition ... to have an area designated as unsuitable for surface coal mining operations." Under the Act, an area can be designated as unsuitable where the mining operation will (1) be incompatible with existing state or local land use plans, (2) affect fragile or historic lands, (3) affect renewable resource lands where mining operations could result in substantial loss or reduction of long-range productivity, or (4) affect natural hazard lands where such operations could substantially endanger life and property. In enacting SMCRA, Congress mandated that each state establish a process to determine which, if any, lands within the state are unsuitable for all or certain types of surface mining operations. In response to this federal legislation, the Kentucky General Assembly adopted a state regulatory program for surface mining that included provisions direct¬ing the Secretary of the Natural Resources and Environmental Protection Cabinet to establish a program for designating lands as unsuitable for surface mining as required by the Act. In recent litigation in Kentucky, several environmental groups filed a lands unsuitable petition, later joined by the University of Kentucky, challenging a proposal by Arch Mineral Corporation to surface mine over 3 million tons of recoverable coal. The petition sought to designate over 10,000 acres of land adjacent to Arch's proposed operations as unsuitable for surface mining operations, basically alleging that the mining would disturb an outdoor laboratory. The filing of the petition activated Kentucky's regulatory scheme for reviewing lands unsuitable petitions that can result in an absolute prohibition against surface mining on the petitioned land for historical, environmental and other related reasons. The designation process involves vague petition requirements creating a situation that Arch argued is devoid of constitutional due process and subject to abuse by the petitioner on many fronts. Arch maintained that the lands unsuitable regulations do not grant adequate protection to Arch's legitimate property rights under the due process clauses of the United States and Kentucky Constitutions and are thus void and unenforceable. The entire process resulting in a decision on the petition took just under 12 months in the Arch case, and although Arch was ultimately successful in preserving its right to mine, Arch's surface mining permit was held up for this period of time. This delay led to the cessation of mining operations by Arch and the idling of over 250 workers. This paper will review the lands unsuitable designation process and the significant implications the process has for existing surface mining operations, currently proposed operations and even those long-range operations not yet contemplated. Special emphasis will be given to Kentucky's lands unsuitable program. Finally, the recent litigation involving Arch Mineral Corporation and its effort to surface mine 81.5 acres of Arch controlled property will be utilized to illustrate this very unusual regulatory scheme. Regulatory background Chapter 30, Subchapter F of the Code of Federal Regulations (C.F.R.) promulgated to implement the provisions of SMCRA, requires that each state establish procedures under the state's surface mining program for designating non-federal and non-Indian state lands as unsuitable for all or certain types of surface coal mining operations. 30 C.F.R. § 764.1. The C.F.R. establishes minimum standards for state lands unsuitable programs and sets out requirements for filing a Lands Unsuitable Petition (hereinafter "LUP"), processing LUPs, decision-making guidelines and hearing requirements. Kentucky has adopted regulations providing for the implementation of the lands unsuitable process as part of the state's regulatory program under SMCRA. The following discussion summarizes the principle components of the Kentucky lands unsuitable program.

Jan 1, 1993

By J. Hong, K. Han, C. Park, C. Yoon, H. Yoon, N. Kim

The contents of three platinum group metals (PGM-platinum, palladium and rhodium), from the spent automotive catalyst, and two NIST SRM (National Institute of Standard and Technology Standard Reference Material, Used Auto Catalysts) were determined by the X-ray fluorescence (XRF) spectrometry. The XRF technique has been proven to be a fast, effective and accurate method in determining not only PGM but also other solid materials of less soluble for wet digestion analysis. The detection limit of the XRF analysis is better than that of the inductively coupled plasma mass spectrometry which usually requires significant dilution to avoid high dissolved solid concentration. However, the XRF technique suffers from a strong matrix dependent problem. The objective of this study was to examine the applicability of the XRF analysis where the sample matrix was not exactly the same as the standard materials with particular reference to PGM analysis. This study enabled to compare the effect of various matrices including alumina, iron, copper and nickel on determination of the contents of PGM.

Jan 1, 2004

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

9.1 INTRODUCTION There are approximately 70,000 abandoned coal mines nation¬wide, which is about 35 times the number of underground coal mines presently operating. The US Bureau of Mines estimates that there are over 8 million acres of undermined land due to the extraction of coal, metals, and nonmetals. Subsidence has affected more than 2 million acres, and more than 99% of the subsidence is related to underground coal mining. There is reason to believe that some of the remaining 6 million acres of the undermined land have a high potential to subside. The expansion of housing, highways, commercial structures, and other facilities has required the use of many areas that are underlain by abandoned coal mines, and this growth will continue. Many subsidence problems are derived from the collapse of aban¬doned underground coal mines. There are numerous abandoned mine workings in the anthracite fields of northeastern Pennsylva¬nia, in the Appalachian bituminous fields, the Illinois Basin, the Rock Springs, Wyoming area, and other areas of the United States (Gray et al., 1976). Various room and pillar patterns of mining have been used in the dipping anthracite seams and the nearly flat-lying bituminous seams with considerable variation in the per¬centage of coal extracted. The progressive deterioration of pillars, mine floors, and mine roofs after long exposure to air and water may later result in the collapse of strata over the mine entries, the crushing of the remaining coal pillars, or the bearing failure of the mine floor beneath the coal pillars. Subsidence then results as the collapse reaches the ground surface in the form of differential strains, depressions, cracking of the ground, and sinkhole devel¬opment. Subsidence over active longwall mines, which occurs concurrently with mining or is completed within a short period following coal extraction, has been studied extensively over the past decade. On the other hand, subsidence over abandoned coal mines receives little attention by the researchers, mainly because it is difficult to predict and takes place decades after mining has ceased. The techniques of investigating the subsidence events over abandoned coal mines are similar to those employed for active mines except that at the outset, it is necessary to determine whether or not the subsidence events are mining-related (Chugh et al., 1986; Cummings and Singh, 1986; Peng and Hsiung, 1986). This calls for the identification and confirmation of abandoned mine workings under or near the affected surface structures. Gen¬erally old mine maps, if available, are acquired, the surface bore¬holes are drilled for confirmation of the accuracy of the mine maps and determination of the potential for continued subsidence. Sub¬sidence monuments are established and periodic surveys con¬ducted to determine the amount and trends of surface movement in and around the affected surface structures; surface boreholes are used to investigate the integrity of the underground structures (i.e., roof, coal pillars, and floor) by TV camera. They are also used for monitoring the vertical and horizontal movements of the subsur¬face strata by Sondex (FPBX) and inclinometer (PFBI), respec¬tively, for determining the continuity of the subsidence events. Tape extensometers, crackmeters, etc., are used to monitor the development trends of major cracks in the structures or on the ground. These data are used to identify the causes of the subsidence events. Finally, abatement methods are selected to stabilize the structures. It must be noted that most subsidence events over abandoned coal mines are reported after the fact, and investiga¬tions are begun some time after reporting, that the subsequent measured movements are generally much smaller than that at¬tained in the active mines, and that due to lack of knowledge about the damage conditions and the exact location of the abandoned mine workings with respect to the affected surface structures, the precise causes of surface subsidence or surface structural damages are in most cases very difficult to identify. 9.2 TYPES OF SURFACE SUBSIDENCE According to Gray et al. (1977), after examining 354 incidents of subsidence above abandoned mines in the Pittsburgh metropol¬itan area, the subsidence features have a mean diameter (i.e. the average of long and short dimensions) from less than 1 ft to 1600 ft, with 84% less than or equal to 15 ft; the subsidence features have a depth ranging from less than 1 ft to 48 ft, with 89% less than 25 ft; 66% of the subsidence features are deeper than they are broad. Nearly 59% of the subsidence features occur with overbur¬den less than 50 ft thick and 81% less than 100 ft thick. No subsidence features occur with overburden thicker than 450 ft (Fig. 9.1). Occurrence of subsidence incidents varies from imme¬diately to more than 100 years after mining (Fig. 9.2). In analyzing the characteristics of approximately 3000 chim¬ney subsidence features along the Colorado Front Range, Matheson and Eckert-Clift (1986) examined historical aerial photographs on 4- to 14-year intervals between 1937 and 1967 and found that the majority of observable surface subsidence features occurred within 30 to 40 years after mining. According to Gray et al. (1977), the most prevalent subsi¬dence features over abandoned mined land are sinkholes, with depths of more than 3 ft, and troughs or sags, usually less than 3 ft deep. Sinkholes are steep-sided pits, while troughs are shallow depressions much wider in area than sinkholes. A. SINKHOLE SUBSIDENCE A sinkhole is caused by the collapse of a mine roof that works its way upward. If it is not arrested during the process it will eventually reach the surface and emerge as a sinkhole. The process is governed by the thickness and character of the overburden, the width and height of the mine openings. Sinkholes are usually 3 to 20 ft deep and may be 2 to 40 ft in diameter, although most are fewer than 16 ft across (Gray et al., 1977; DuMontelle and Bauer, 1983). Newly formed sinkholes have steep sides with straight or bell-shaped walls. At times, they appear to be conical in profile with the apex upward. If the topsoil collapses, the top portion will widen to form an hour-glass shape. Sinkhole subsidence usually occurs over abandoned mines less than 165 ft deep (Hunt, 1979). Matheson and Eckert-Clift (1986) found that chimney sink¬holes are likely to occur when the ratio of overburden thickness to mining height (h/m) is less than 4 to 5. When h/m is between 5 and 10 to 11, the potential occurrence of chimney sinkholes decreases rapidly. When h/m is more than 10 to 11, less than 10% of the mine openings that collapse will induce sinkholes on the surface.

Jan 1, 1992

By R. Mohan Srivastava

In any operating mine, especially in precious metals operations, immediate improvements in profitability m readily achievable through more effective grade control. Just as the oil industry has come to recognize that enhanced oil recovery (EOR) in existing oil fields yields a higher return on investment than exploring for new oil, so too must the mining industry recognize the benefits of enhanced metal recovery (EMR). Current grade control practices are generally dismal. The very word "control" suggests a willingness to make the best of a bad situation -- as in "damage control" or "disease control" -- and a failure to perceive the opportunities for improved profit. While damage and disease can merely be controlled, success and improved profit can be engineered. This paper presents one approach to enhanced metal recovery. It shows how existing methods can be used to address the issue of ore/waste discrimination. The following sections outline the problem, describe the current state of the practice of grade control, propose an alternative approach and. illustrate the application of the proposed alternative to actual blasthole data from an operating gold mine.

Jan 1, 1992

By D. L. Monroe

Technical service is assuming an increasingly important role in the sale of asbestos fibre,, Manufacturers are examining raw materials more closely than ever before in order to, obtain the most efficient usage in their processes. Asbestos is one of the more difficult materials to evaluate and consequently has been are of the last to be subjected to evaluation. The main problem encountered in the evaluation of asbestos fibre is that minor differences in grade and texture are not shown up by chemical analysis, and are identified only by specialized physical analyses or actual production use. However, such minor differences become more critical as manufacturing processes are made more efficient, and many purchasing agents and plant chemists are applying a closer scrutiny to their supply of raw asbestos fibre. Many processes have been formulated around grades and qualities of asbestos fibre, which were standard some time ago, but which may now be subject to modification and improvement.

Jan 1, 1959

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993