Search Documents

By R. L. De G. Solms

INDEX 1. INTRODUCTION 2. FLOODING 3. THE PLUG 4. THE FIRST ATTEMPT 5. THE SECOND ATTEMPT 6. PUMPING 7. TIGHTENING OF THE PLUG 8. SHAFT REPAIRS 9. POST-MORTEM 10. CONCLUSION

Jan 1, 1987

A Directory of Computer Programs Applicable to US Mining Practices and Problems. A. L. Sanford, T. L. Myers, and J. F. Stiehr. USBM OFR 131-78, Nov. 1977. A Master Environmental Control and Mine System Design Simulator for Underground Coal Mining. Tape MDS-5. Pennsylvania State University. USBM CT 1.77, Dec. 1975. Contains computer programs on a dynamic general purpose computer simulation model for underground coal mining. A Method for Computing Stabilization Pressures for Excavations in Incompetent Rock. J. D. Dixon and M. A. Mahtab. USBM RI 8128, 1976. Describes technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. Accident Cost Indicator Model to Estimate Costs to Industry and Society From Work-Related Injuries and Deaths in Underground Coal Mining. Vol. I.III. D. G. DiCanio, A. H. Nakata, D. Colvert, and E. G. LaVeque. OFR 39(1)(3)-77, Dec. 1976. Describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents In underground coal mines. An Interactive Computer System for Evaluating Coal Mine Illumination. R. Goldstein. USBM OFR 110-80, March 1980. Computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights. Analytical Modeling of Mine Roof Behavior Using Statistical Material Properties. R. T. Langland and F. J. Tokarz. USBM UCRL-51876, Aug. 1975. Analytical study of coal mine roof behavior using a computer model of a room-and-pillar mining method. Application of a Total System Surface Mine Simulator to Coal Stripping. Vol. I-VII. Pennsylvania State University. USBM OFR 33(1)(7)-78, Aug. 1978. Describes model development, input and output documentation, three case studies of an open-pit materials handling simulator, and development of two equipment selection models and a cost model. Characterization of the Structural Behavior of Rock Masses. Vol. I-II. L. R. Herrmann and M. A. Taylor. USBM OFR 67(1X2)-75, Sept. 1974. Computer subroutines for characterization of rock behavior, Including variability of properties within the rock mass, planes of weakness orthotropy, strength criteria, and post-failure behavior. Coal Mine Electrical System Evaluation. Vol. I-VII, L. A. Morley, et al. USBM OFF! 61(1)(7)-78, 1977. A concept to improve underground coal mine electrical system safety and availability. This proposed technique is based upon the ability to predict incipient failures in the mine power system. Prediction is made possible by a new method which uses a minicomputer to implement pattern recognition algorithms. Computer Modeling of Fluid Flow During Production and Environmental Restoration Phases of In Situ Uranium Leaching. R. D. Schmidt. USBM RI 8479, 1980. Describes development and application of a computer model for simulating the hydrological activity associated with in situ leaching. Interpretation of Rock Mechanics Data, Vol. II (A Guide to Using UTAH2). W. G. Pariseau. USBM OFR 47(2)-80, June 1978. Brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis. Iterative Approximation Techniques for Microseismic Source Location. G. H. Dechman and Meng-Cherng Sun. USBM RI 8254, 1977. Iterative approximation method for microseismic source location developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems such as slope failure in an open-pit mine. Limits and Cost Sensitivity of Alternative Parting Handling Methods. Vol. I-II. T. E. Finch, D. R. Haley, and C. J. Speaks, Jr. USBM OFF! 117(1)(2)-77, March 1977. Programs to examine alternative methods of handling the parting between two coal seams in a surface mining operation. Alternative methods consist of equipment implementation in either a stowing or haulback technique. Methane-Water Flow in Coalbeds. H. S. Price. USBM CT 1-79, April 1972. This computer program calculates transient, two-dimensional, gas¬water flow in a porous medium. Plastic Canopy-A Computer Program for the Structural Analysis of Protective Canopies. K. D. Winters, G. A. Gavan, and J. C. Ault. USBM IC 8795, 1979. Presents a FORTRAN IV program for the structural analysis of protective canopies used In underground mines and rollover protective structures used in surface mines. The Three-Dimensional Structural Analysis of Double-Entry and Single-Entry Coal Mines. Vol. I-III. Agbabia Associates. USBM OFF 16(1)(3)-80, Oct. 1978. Describes the computer program designed to perform a three-dimensional finite element analysis of an instrumented section of double- and single-entry coal mines. Underground Mine Evacuation Plans Analyzed by Computers. D. Tesarik, D. Nicholson, and A. B. Boghani. MSHA, Vol. 4, No. 5, Oct. 1979. USBM has developed a computer program to evaluate and construct mine evacuation procedures and plans.

Jan 11, 1981

The latest resource estimate for the Caspiche gold/silver/copper project in the Maricunga region of Chile was released by gold explorer Exeter Resource Corp. The resource is low grade, but bulk minable and drilling to date has shown a NI 43-101 compliant inferred resource of 1,117 Mt (1.23 billion st) grading 0.55 g/t (0.016 oz/st) gold, 3.81 g/t (0.111 oz/st) silver and 0.22 percent copper. Exeter said these findings make the in situ metals amounts of 609 t (19.6 million oz) of gold, 4.4 kt (137 million oz) of silver and 4.84 billion lbs of copper, which the company relates as 33.7 million gold equivalent ounces using assumed metal prices of $23.33/g ($800/oz) for gold, 35 cents/g ($12/oz) for silver and $2/lb for copper. The deposit is almost midway between Barrick?s Cerro Casale gold deposit and Kinross? Refugio Mine. In a statement Exeter chairman Yale Simpson said ?This updated resource estimate places Caspiche firmly among the world?s largest gold-copper discoveries in recent years and clearly supports our decision to aggressively drill the property, despite the global economic decline. ?We expect that the very substantial copper and silver credits will be extremely important, and will markedly impact the potential viability of Caspiche. Specifically, using metal prices of US$2/lb copper, $23.33/g ($800/oz) gold and 35 cents/g ($12/oz) silver, the 4.84 billion lbs of copper and 4.2 kt (137 million oz) of silver are equivalent to 376 kt and 62 t (12.1 and 2 million oz) of gold, respectively. ?Our recent drilling has defined what appears to be a coherent higher grade central zone associated with a definable early stage diorite intrusion. We expect this zone will be important in developing various mining and economic models for the project,? Simpson said. Exeter is still drilling the deposit to expand the re-source estimate further to the southeast and at depth and to upgrade the higher grade central zone to the indicated category. Simpson said, ?Exeter intends to enhance the value of Caspiche by continuing to de-risk the project through ongoing exploration, metallurgy, engineering, water and environmental studies. These studies will continue through the next 12 months and will lead to a conceptual development study. A timeline for the release of that study is being formulated. The project budget for the next 12 months is C$14 million.? Mineweb reported that Caspiche is likely too big of a deposit and at too high of altitude for Exeter to handle alone. Exeter will be looking to other majors, or perhaps the Chinese, to help develop this huge orebody. But, in the meantime, it also has its high grade Cerro Moro deposit in Argentina, which could be brought to production relatively quickly and at relatively low cost.

Jan 1, 2009

By B. Das, B. K. Mohapatra, K. S. Narasimhan, S. K. Bhaumik

The iron ore slimes (d80 ~ 50 µm) generated at Noamundi iron ore washing plant (TISCO), assaying 57% Fe, 4% Si02 and 8.3% A1203, have been subjected to hydrocyclone studies. The effects of different design and operating parameters have been studied to get a product suitable for subsequent use in the sinter mix. The studies indicate that it is possible to obtain a product containing 64% Fe, 1.4% Si02 and 3.5% A1203 with a recovery of 49% iron. The process involves classification followed by separation in a hydrocyclone. By this method, the overall yield of iron ore production in the plant is expected to increase by 8%. Microscopic examinations and X-ray diffraction studies were conducted to elucidate the mineralogy and liberation characteristics of Noamundi iron ore slimes. This paper deals with the findings of the investigations.

Jan 1, 1993

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author's most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

By Jozef Stachulak

Prof. H. Bystron: "An Application of the First Law of Thermodynamics to Winter Dry Air Flow in Mr. Stachulak's Mine Model". [ ]

Jan 1, 1980

By VIVEK KUMAR HIMANSHU, PK SINGH, AK MISHRA, MP ROY, RAVI SHANKAR

Underground blasting has many challenges. The primary aim of blast designers is to optimize drilling and blasting parameters to deal with the associated challenges. Optimizing these parameters is currently based on various rules of thumb, which have many site-specific limitations. Accordingly, computation of these parameters using empirical rock fragmentation predictors can be useful for blast designers. This paper presents the results of work on burden-spacing determination by back-calculation from the empirical Kuz-Ram model for underground stope ring blasting.

By Ignacio Salazar

Somebody sure gave me the wrong title. I can talk much more freely about the impact of the anti-nuclear movement on the DRILLING industry in New Mexico. In a word, it is being "clobbered." It doesn't seem like very long ago that my brothers and I were busy trying to find enough new equipment (and trying to talk bankers into lending us enough money) to keep up with drilling work we could get. Seemed like no matter how hard we worked, and how much money we borrowed, we were always one step behind where we wanted to be. We had so many holes to drill that all our crews were working three shifts a day, and over several states. The nation needed energy, and we were ready to help supply it. Exploration and development drilling jobs were all going full-blast. We had trouble keeping up with them. With luck, we figured we'd be able to get all our equipment out of hock before all the necessary uranium mines were developed.

Jan 1, 1979

By D. Vavadakis

Abandoned bauxite surface mines in the Parnassos area may be rehabilitated using bauxite residues as filler. The objective of this study was to estimate the percentage of precipitation that may infiltrate through the bauxite residues to the lower geological formations when they are disposed off in mine open pits. Two scenarios were investigated simulating: a) available field tests, and b) a demonstration test that was planned to be performed in an abandoned open pit close to the Aluminium of Greece plant. It was indicated that the annual infiltration from bauxite residues disposed off in the demonstration test for the most probable scenario is very low, equal to 13.17mm corresponding to 3.1% of the annual precipitation. Furthermore, it was estimated that the annual percolation from the field tests is approximately 4.4%, very close to the infiltration values measured in the field tests for the same period.

Jan 1, 2006

By R. E. Brewer

Phelps Dodge Mining Company (Phelps Dodge) is operating a pressure leach vessel (PLV) for copper concentrates at the Bagdad Mine facility in Arizona. This single PLV unit was engineered and constructed based on continuous laboratory testing, reaction chemistry and kinetics, and available pressure vessel technology. The challenge of designing for optimum process retention time, agitation, oxygen mass transfer, temperature and pressure will be reviewed in this paper. The PLV interior lining, agitation equipment and compartment configuration chosen for the PLV will also be reviewed.

Jan 1, 2004

By R. J. McGregor, Deepak Malhotra

Engineers frequently encounter situations where decisions that are counterintuitive to the logically trained engineering mind are made because of other influences, whether they be financial, social, cultural, or environmental. Such influences can overrule the "logical" decision-making process. The aim of this book is to explore some of the nontechnical issues, which most engineers don't learn about in school, that can have a major impact in the mining industry. This chapter gives a brief overview of this volume and introduces the topics that will be addressed.

Jan 1, 2001

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of poros¬ity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geologi¬cal Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Re¬sources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of dissemi¬nated gold deposits a profitable technique.

Jan 1, 1989

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of porosity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geological Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of disseminated gold deposits a profitable technique.

Jan 1, 1990

By Simon J. McDonald

In late 2007 Neptune Minerals Plc. commissioned Genesis - a leading consultancy and engineering company affiliated to the Technip group - to undertake a Seafloor Mining Conceptual Study for mining of Seafloor Massive Sulphides (?SMS?) in Neptune?s New Zealand licenses. A key deliverable of the study was information to de-risk the perception of SMS mining for investors the minerals, and that deep-sea mining of SMS material is technically feasible, commercially viable and can safely be managed as a sustainable marine resource industry. The aim of the study, completed in April 2008, was to evaluate alternative existing marine technologies for seafloor mining, ore lifting, dewatering and surface offtake, considering the following parameters: ? Efficiency; ? Reliability; ? Safety; ? Environmental impact; and ? Cost

Jan 1, 2008

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By Noel C. Joughin, Orrie Fenn, Brian E. Protheroe

Work has shown that the use of high-pressure water jets enhances the performance of mechanical cutting in very hard rock. To assess the potential of this approach for use in conjunction with free rolling cutters, a series of tests has been conducted using both disc and button type cutters, to determine the relative effects, on cutter performance, of variations in relevant jet and cutting parameters. In these tests it was found that water jet assistance can result in reductions in the forces on a free rolling cutter typically of the order of 40%.

Jan 1, 1985

By George D. Lessner

I'm sure that everyone at this meeting is aware of the current problems facing the U.S. metals mining industry. Prices are depressed and expected to remain depressed for quite some time. On the other hand, industrial minerals, including talc, are doing quite well. The profitability of industrial minerals has sparked considerable interest on the part of many companies in expanding into industrial minerals. Our company is one of those actively seeking to expand its position in industrial minerals. It is appropriate that the A.I.M.E. asked me to speak to you regarding entry into the talc business. So how do you get into the talc business? Earlier speakers have explained how to locate, mine, process, and market talc, so you have the "how ton.

Jan 1, 1984