Search Documents

By John P. Norton

Microcystaline silica has been mined in Illinois from the Clear Creek formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. Production of this silica, consumed mainly by the abrasives and coatings industries but also sought after for many filler/extender uses, has grown with the economy with several new applications overshadowing traditional markets in recent years. Such an important commodity was given the early attention of the Illinois State Geological Survey and a very complete report was issued in 1953 (Report of Investigations No. 166), authored by J. E. Lamar. The mining and processing of the silica ore has changed very little since the first reported production in 1906, although emphasis has been placed on the production of the finer sized grades to meet newer market requirements. Industrial Mineral Notes 40, published by the Illinois State Geological Survey in June 1970, describes a method by which a less than 1-micron fraction could be commercially produced from the readily available finest commercial grade presently being marketed (99% minus 10 microns). The finer grades exhibit to a lesser degree the reinforcement, high flatting efficiency, thickening and dry brightness properties associated with the synthetically produced silicas. It is expected that the extremely fine grades of microcrystaline silica will become accepted in the markets that now use a combination of precipitated silica and less expensive extender/filler minerals such as kaolin or calcium carbonate.

Jan 1, 1976

By D. Boufounos

The large open pit areas of surface mining as well as the huge quantities of residues generated during the digestion of bauxite with sodium hydroxide solution to produce alumina are considered as the most important environmental problems associated with the exploitation of bauxites. Aluminum of Greece, which is the only aluminum refinery in the country, located in Agios Nicolaos, Paralia Distomou, Viotia, produces almost 680.000 tones of bauxite residue annually which is pumped through pipes from the refinery to the sea bed of Antikira gulf. In order to avoid any kind of environmental problems related to this disposal method and to reduce the total volume of bauxite residue disposed of in the environment, Aluminium of Greece investigates several alternatives for bauxite residue utilization. In this framework, it also examines the potential use of bauxite residues as a filler in abandoned mining open pits. Bauxite residues are mainly composed of fine particles of silica, aluminum, iron, calcium and titanium oxides and hydroxides. Furthermore, the material presents low hydraulic conductivity, slightly higher than the limit posed for low permeability layers by the EC landfill directive. Based on these properties the dry disposal method was selected for disposing bauxite residues in mining open pits since it has many advantages such as reduced overall disposal cost, effective use of land and minimum environmental impacts. The results obtained for this method, which is investigated at demonstration scale, are presented in this paper.

Jan 1, 2005

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By Harold L. Lovell

The extensive heterogeneity of coal is a fact long recognized by scientists and engineers. However, until recent years the practical implications of such heterogeneity have more often been realized from an undesirable experience than from knowledge or forethought. Variations in the properties of coal, even within the same seam, eventually lead to procedural modifications in mining, handling, preparation and utilization. The concepts considered here propose an enhanced application of information, detailing these properties, realizing the uniqueness of any given coal seam but the practicality of a common approach. Coal preparation practice has been designed primarily for the control of ash and sulfur content to meet market specifications which are similarly specified, Other physical characteristics of size and friability are also commonly employed and, to a lesser extent, properties which are implications of rank. The consideration of petrographic data as indicators of origin, thus total physical and chemical properties, has generally been overlooked as a realistic tool in-the exploitation of coal as a resource. The evolution of descriptive techniques, whether petrographic, physical, or chemical, capable of universal application with any rank of coal, is still beset with problems.

Jan 1, 1968

By J. G. Smith

Of the variables affecting the electrical properties of coal measure rocks, water content is by far the most important, This paper describes specially developed apparatus and methods of measuring electrical conductivity and permittivity at constant humidity conditions. Electrical properties variations were measured for Applachian and Illinois, U.S.A. coal 2 basin samples in the frequency range 2 X 10 to 2 X 10 Hz. Coal measure rock electrical behavior, when correlated with mechanical behavior, is potentially useful in a number of mining applications.

Jan 1, 1985

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By M. F. Corcoran

Rapid advances have been made in the past few years in the application of automatic controls and instrumentation to iron ore pelletizing plants. Present practice in applying instrumentation and control to the Grate-Kiln system of iron ore pelletizing is described. Major control points and loops are tabulated. Future trends in the application of digital control including computer data logging systems are described.

Jan 1, 1965

By K. Hanna

This paper describes a method to improve coal mine entry intersection design. The method considers the effect of in situ stresses, local geologic conditions, rock physical properties, and mining sequence. Development of the method is discussed, including the results of field instrumentation studies and numerical modeling investigations. Data required to evaluate the effects of roof span, mining sequence, entry orientation, and bolting patterns on intersection stability are also presented. Ground control studies conducted by the U.S. Bureau of Mines in two underground mines in the Illinois Coal Basin have shown that in situ horizontal stresses and roof geology have a critical effect on intersection stability. Methods to reduce the adverse effects of these parameters are emphasized. Typical failure behavior associated with specific geologic and horizontal stress conditions is' presented to illustrate proposed control methods to alleviate adverse ground conditions.

Jan 1, 1988

By William G. Doepken

The extensive use of rubber-tired support vehicles as a complement to a fleet of load-haul-dump and drill jumbo units has proved invaluable in maintaining scheduled multilevel/multiheading development drifting advances at the Henderson Mine. Support equipment, whether self-powered or towed, releases primary drill-blast-muck equipment from the supportive functions of ground control, utilities installation, steel and concrete construction and supply handling, thus providing both balance and increased flexibility to an underground, rubber-tired mining system. Experience has indicated that increases in man productivity and improved safety and working conditions coupled with decreases in overall costs and mining cycle times are realized with the inclusion of support vehicles in the mining fleet.

Jan 1, 1976

By James McManus

The Lornex mine is located on the Southern slope of the Highland Valley in South Central British Columbia. The large low grade deposit was discovered in 1964; stripping began in 1970, and the mill started commercial production in October of 1972. The orebody is classified as a complex porphyry type having as major constituent quartz diorite, with varying amounts of quartz, grano diorite, and porphyry. A substantial degree of alteration is evident in the host rock, and this became the key factor in major equipment selection for the grinding section. A pilot plant was constructed on the property capable of treating 100 TPD of ore. The ore was mined to be as representative as possible of the entire orebody by sinking a shaft and cross cutting the deposit underground.

Jan 1, 1975

By K. Rajamani

A mathematical model based on the pertinent fluid dynamic equations to predict the performance of the hydro cyclone has been developed which will eventually replace the empirical model. Experimental measurements of fluid velocity profiles made in a 75 mm hydrocyclone by laser Doppler velocimetry (LDV) agree well their predictions by solving the Navier-Stokes equations numerically. Particle slip velocity and particle trajectory were computed which in turn, yields separation curve of the hydrocyclone.

Jan 1, 1988

By R. W. Ballmer

Prior to initiating construction of a new mineral development project, sponsoring organizations must be convinced that the operation will be viable. Proof is typically provided by the feasibility study. Considerable man hours will be spent in assessing and evaluating data on the deposit, its environment, and the means of development. Impact studies must be made for various scales of operation, inclusion of by-products, new methods of treatment, deferent levels of integration, and infrastructure configuration. Examples of current materials handling cost estimates are provided from the ongoing investigation in which Amoco is a participant at Ok Tedi in Papua New Guinea and Gag Island in Indonesia.

Jan 1, 1979

By Brian McInnes, Joseph A. Sopko, Behzad Khorshidi

"The Port Mann Main Water Supply Tunnel involves a 1km long tunnel beneath the Fraser River from Surrey to Coquitlam, BC. At depths of up to 60 m below ground, the earth pressure reached 6 bar. The tunnel is constructed using an EPB TBM and gasketed precast concrete segmental liner. The tunnel and two shafts were constructed in a variety of soil conditions ranging from soft to stiff clays and silts, to compact to very dense sands and gravels. After approximately 800m of mining, a very dense and highly variable soil group consisting of cobbles and boulders halted the TBM. Several options were considered to stabilize the TBM face so an intervention could be conducted. Although de-watering was considered, there was risk of settlement to the Port Mann bridge piers, which was within 500m of the tunnel. Hyperbarics were also considered, however, the cost, schedule and uncertainty of the work that needed to be done, made it a risky option. Ground freezing by Liquid Nitrogen was chosen as the best solution, which would provide a frozen block around the face of the TBM. A temporary platform on the river was designed and constructed to enable drilling and installation of the freezing pipes and temperature monitoring equipment. The operation required close coordination among the tunnelling, marine and freezing sectors. Following the intervention, the TBM successfully broke through the reception shaft, and the remaining project was completed. This paper describes the design, construction and operational approaches used for the freezing and serves as a basis for future projects requiring expedited ground freezing."

Jan 1, 2016

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME's Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation's (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM's closure.

Jan 1, 1997

By Dinah O. Shumway

California's annual production of >11 million tons of cement, at a value of over $640 million, comes from eight companies, which operate 11 plants. Cement is California's second most important mineral commodity, representing 25% of its total annual mineral production. Although most of the cement produced is consumed within the state, current export locales include the Pacific Northwest, Nevada, Arizona, Utah, and New Mexico. An enumeration of the components required to produce cement is deceptively simple: calcium oxide (65%), silica (20%), alumina (4-5%), iron (3-4%), and calcium sulfate (4%) as a retardant admixture. The last, and most expensive, ingredient in cement manufacture is energy. Detrimental materials in cement mixes include excess .magnesium, alkalis, heavy metals, sulfur, and other volatiles. Each of the 11 cement plants in California requires a unique chemical solution of combined raw materials to produce a uniform product: portland cement. The geologist proposing solutions for the additive raw materials in cement manufacture must have a thorough knowledge of a particular cement plant's needs. In the California cement market, keeping the costs of additive raw materials down is one way to also stay competitive, and using a combination of natural and waste materials as additive raw materials allows cement producers to stay competitive.

Jan 1, 1999

By Susanne Pignolet-Brandom

This paper examines the viability of using the QEM*SEM automated scanning electron microscope for the determination iron sulfide and calcite volumetric percentages. The analytical reliability was verified by comparing elemental abundances calculated for fourteen samples using the QEM*SEM volumetric percentages and appropriate mineral compositions and elemental abundances determined by standard laboratory procedures. The abundances were comparable, thus demonstrating suitability of this technique for evaluation of the acid neutralization and generation potentials of mining wastes.

Jan 1, 1990

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980