Search Documents

By S. R. Rao, J. A. Finch, E. El-Ammouri, K. Ngoviky, P. A. Disten

Sludges produced by lime treatment of acid mine drainage (AMD) can contain significant quantities of base metals which represent both a potential hazard and a loss of values. A new technique for metal recovery from sludge is proposed by combining selective acid leaching and adsorption of metal ions by activated silica sol. The process is demonstrated on two AMD sludges, one containing primarily nickel and the second zinc. They were first treated with sulphuric acid (pH 3.5) to selectively leach the target metals and then activated silica sol was added to the leach solution to adsorb the nickel and zinc. Thickening and centrifuging gave about 90 percent rejection of the input volume to effluent. The adsorbed metals were redissolved by strong acid into a concentrated solution relative to the feed and the silica sol was recycled.

Jan 1, 2000

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"BACKGROUND The design, development, fabrication, and test of a cryogenic supply for a refuge alternative is part of a larger effort funded by the National Institute for Occupational Safety and Health and managed through a Space Act Agreement with the National Aeronautics and Space Administration at the Kennedy Space Center, FL to create cryogenically based life support equipment responsive to the needs of miners as required by the Miner Act of 2008. This work is done by a joint contractor/NASA team. In particular, the Cryogenic Refuge Alternative Supply System (CryoRASS) serves to provide a respirable air source to miners confined for 96 hours in a mine refuge alternative. This system stores liquid air in a zero-loss cryogenic reservoir (Dewar) until an emergency requires use. The system does not require electric power when in use by miners. Because of the very cold nature of the liquid air, considerable heat stress relief and reduction of humidity is provided in addition to the required replenishment of oxygen. Moderate dilution of CO2 also occurs.INTRODUCTION The design of this new cryogenic refuge alternative supply system (CryoRASS) uses NASA/Kennedy Space Center technology as a development baseline. The design stores cryogenic (liquid) air that is warmed in an air handler box and the resulting gaseous air is introduced to the chamber that not only causes air circulation, but relies upon environmental and human heat to expand the liquid air to a gaseous state. Therefore, the primary benefits of the liquid air source, besides atmosphere maintenance (oxygen), is refuge cooling and dehumidification. This results in reduction of human heat stress and this occurs without the need for electrical power in the refuge chamber. This reduction is a major factor in ""apparent heat"" and the human perception of comfort. Another benefit with introduction of ""air"" vs only ""oxygen"" is the dilution of carbon dioxide. The volume of new air will displace existing refuge air and this air laden with humidity/CO2/low O2 passes out of the refuge relief valves. These RVs should be strategically placed to vent stagnant air preferentially. An initial system test was conducted in our Florida facility in a production 10-person hard chamber for 96 hours. Last year (2014) the system was tested with a 23 person inflatable refuge alternative in Bruceton. For this test, the CryoRASS air handler was redesigned to offer superior characteristics when installed in a Built-in-Place refuge alternative. This report describes the results of the modified system being tested in the Pittsburgh Experimental Mine while attached to a 30 person refuge for 96 (+/-) hours."

Jan 1, 2016

Over the last two decades, the mining industry has spent considerable time and effort in installing sophisticated control systems (including expert systems) to regulate and improve the performance of AG/SAG mills. Yet the need for these systems is often overlooked – unmeasured and uncontrolled variation in the feed material. With AG/SAG mill technology replacing rod and ball mills as primary grinding equipment, the need for careful and thoughtful feed preparation has gone. To maximise mill throughput, operations need to better understand the ore characteristics affecting AG/SAG mill performance. Industrial operating data will be used to illustrate these ideas and concepts. It is often quite surprising which ore characteristics that are the most influential on mill throughput.

Jan 1, 2004

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator's location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By K. O. Johnson

Contaminant transport of mine and mill tailings is controlled by the hydrologic flow regime and the geochemical mobility of the contaminants. Contaminant' mobility is primarily determined by chemical reactions occurring within an interface zone between the tailings and soil The large geochemical differences between tailings and groundwater create a disequilibrium in the groundwater with respect to the soils when seepage from tailings enters the groundwater. Precipitation and dissolution reactions involving the major chemistry occur to return the perturbed system to chemical equilibrium between groundwater and minerals. Retardation of trace elements depends upon the chemical character of the groundwater and the adsorption substrates. In the case of uranium mill tailings, the mobility of contaminants is controlled primarily by precipitation/dissolution reactions which neutralize the pH, modify the Eh (redox potential), and produce highly adsorptive substrate for retardation of trace elements.

Jan 1, 1988

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By Larry Cook

During the past year the news media has come in for its share of criticism. Some of it, without doubt, is justified. Much of it, like that which has been leveled against some of the rest of us, is not. We can sympathize with the newspapers and magazines, the radio and television stations. Like the coal industry, which I represent, they are a part of the free enterprise system. They depend upon advertising for their existence, and advertisers patronize those media which reach the most people interested in their product. The various news media are therefore In avid competition for circulation. Although they do have an unquestioned influence on the public, they are primarily a reflection of the public and it is in this context that we will consider them. Granted that this reflection is sometimes a bit distorted, let us admit that any subject which does not strike a responsive chord In the public will soon be dropped by the media.

Jan 1, 1970

By Joe D. Allison, Tom D. Baugh

The analysis for total cyanides (CN, or the cyanide due to the combination of free, weakly associated and refractory cyanide complexes) is required by most regulatory agencies for determination of effluent compliance. This method requires a distillation of the sample at low pH's and is most often sent to contract laboratories at a high time and monetary cost. This paper describes a new micro­distillation apparatus which allows for a multiple of CN,"' analyses to be carried out simultaneously saving both time and money. It can be used in the field, since only electrical power is required for the method. While not being appropriate for reporting values to the respective regulatory agencies as of yet, it is quite valuable for screening a large number of samples prior to submission of the samples to a contract lab for "official" reporting.

Jan 1, 1990

By David Lunt, Paul Messenger, Peter Allen

The Rawas Gold Project in Indonesia has a high silver ore with a ratio of approximately 25:1 Ag/Au. Four process flow­sheets were considered during the development phase, ie. full Merrill Crowe, CIP, CIP with zinc cementation of eluate and a hybrid Merrill Crowe - CIP circuit. The process plant was constructed using a CIP circuit with zinc cementation of eluate. Unusual aspects of the design include an elution circuit designed to strip three batches of car­bon per day and an elution column designed to operate with either upward or downward solution flow. Significant improvements implemented since starting up the plant include the use of local materials and labour for relining the mill, a change from lime to caustic soda for pH modification and the elimination of caustic soda dosing to the elution pre-soak step.

Jan 1, 1998

By S. Di Muzio

Sulphate Reducing Bacteria (SRB) are hetero-trophic anaerobic micro-organisms that can be used to remove sulphates and heavy metals from Acid Mine Drainage (AMD), heavy metal-bearing streams with high iron and sulphate contents and low pH, generated by sulphur bio-oxidation in abandoned mine districts. After the preliminary chemical precipitation of iron with carbonate stones (I step, chemical precipitation) SRB can be used to reduce sulphates to sulphurs then favouring heavy metal removal as sulphur precipitates (II step, biologically mediated precipitation). In this work the experimental results of heavy metal and sulphate removal from column tests were reported. Sulphate and heavy metal abatement in fixed bed column was performed using chemically pre-treated samples of synthetic AMD. Attenuation of toxic effects of treated samples was also ascertained by toxicological tests of germination and radical growth with Lepidium sativum.

Jan 1, 2006

By M. P. McArthur

General mining practices at W. R. Grace's Bonny Lake mine are much the same as those used in open pit phosphate mines in Central Florida, except for the difference in the depth of the overburden which introduces many variations, From 1945 to 1961 the mining at Bonny Lake has been from an area in which the overburden averages from 55 to 60 feet and in several locations exceeded 65 feet. The matrix thickness will average 15 to 18 feet for the areas mined. As you can see from the above depths a total hole depth will average from 70 to 75 feet.

Jan 1, 1962

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

By R. Hemp

This paper describes work carried out to obtain a heat balance in the B3 shaft longwall stope at Blyvooruitzicht gold mine. Recordings were made of the temperature of the air and chilled water entering and leaving the section during three periods, August 1 September 1977, November 1 December 1977 and March 1978. These recordings, together with numerous other measurements were used to determine the rate at which heat was being removed from the section by the various fluids flowing through the section. The rate at which heat was entering the section was then calculated, by considering each source in turn. These two sets of figures made it possible to draw up a heat balance, and also obviously gave vital information on the magnitudes of the various heat sources and on the methods used to remove heat. In general reasonable heat balances were obtained, the errors being in the range -6 per cent to +22 per cent.

Jan 1, 1980

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By Andrew Neale

ERIC GUTIERREZ: With that, we'll go ahead with the final speaker of the day, Andrew Neale. Andrew has a master's of science degree in mineral processing from the University of Alberta. He worked at the Falconbridge in Sudbury area, also at Brenda Mines, and then he became part of the Brenda Process Technology group in British Columbia. He joined Freeport in late 1993 in Indonesia, and was involved in process control and automation. He is now the senior manager of metallurgy in New Orleans. He's responsible for designing Freeport's new 100,000-ton-per-day expansion concentrator, which is currently being commissioned. Please welcome Andrew. ANDREW NEALE: With the ongoing explosion in digital computing power, there seems to be no limit to what can be modeled, simulated, and controlled in the mineral processing plant. However, at each stage of development of a control system, it is necessary to complete a cost-benefit analysis for justifying the move to a higher level of control. Incremental improvements in plant performance, while often significant, must be weighed against the costs of implementation and long-term maintenance. This presentation will provide examples of what the author believes are misplaced or misguided process control efforts and make a case for the KISS principle as applied to process control.

Jan 1, 1998