Search Documents

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By Carl Erickson, James Hislop

INTRODUCTION As practiced today, longwall mining is a mechanical version of an established mining system. The equipment for longwall mining consists of four basic units: roof supports, face conveyor, winning or mineral-getting ma¬chine, and stage-loader conveyor. The system mines relatively thin slices of mineral across a predetermined face length in a virtually continuous sequence. As the winning machine cuts, the mineral is loaded automatically onto the face conveyor. In turn, the face conveyor is pushed over into the newly cut track by hydraulic rams attached to the conveyor and the roof supports. The roof supports then are lowered individu¬ally from the roof, advanced to the repositioned con¬veyor, and reset to the roof. At the end of the pass, the longwall cutter is pushed over, and a slice is taken in the opposite direction, so the system repeats itself. Fig. I illustrates a typical longwall mining system. The principle behind the longwall mining system is that the roof is supported only immediately adjacent to the worked seam, keeping the blocks of immediate roof clamped securely from the face to the rear of the sup¬ports. At the rear of the supports, the roof is allowed to fall and break up, with the swell of the broken material eventually establishing an equilibrium in the strata be¬hind the mined area. Fig. 2 illustrates the principle of longwall support. There are two distinct types of longwall mining. The longwall retreating system is the most common in the United States, South Africa, and Australia. The longwall advancing system is the most common in the re¬maining industrialized countries such as Britain, Ger¬many, Poland, and the Soviet Union. The longwall retreating system comprises a mining panel, where the roadways that form the head entry (end at which mineral is delivered from the face con¬veyor to a stage-loader conveyor) and the tail entry are predriven before the longwall units starts production. In the longwall advancing system, the longwall unit makes the head and tail entries as the face advances, utilizing various techniques to prevent the entries from being destroyed as they are left in a consolidating gob area. Fig. 3 illustrates the comparative approaches of the longwall retreating and advancing operations. As with most other underground mining systems, there are many variations on these two basic systems, using combinations of the systems that are dictated by

Jan 1, 1982

By Siegfried Zell

INTRODUCTION Denmark is a small country with a population of about 5.5 million in the north of Europe. A substantial part of Denmark consists of islands, and the Danes have been familiar with ferry links between their islands for ages. However, their wish for fixed links has resulted in the con¬struction of bridges between most of Denmark's islands in this century. (Fig. 1) A fixed link across the Store Belt or Great Belt, Denmark's most important waterway bet¬ween the island of Fyn and main island of Sjaelland, on which the capital of Copenhagen is situated, has remained to be constructed hitherto. In 1987, the Danish government decided that the Great Belt should be crossed by a fixed link, incorporating a two-track railway line and four-lane motorway. The Storebaelt Forbindelsen AS, a joint stock company in the sole ownership of the Dan¬ish state, has been established for the purpose of planning, constructing and operating the Great Belt Link. The company will refinance the construction project by charging toll to the motorway users and fees to the state railway. Here it should be mentioned that Denmark and Sweden are about to jointly realize the fixed rail and road link across the Øresund or The Sound between Denmark and Sweden on the basis of the realization model of the Great Belt link. At present, the project is at the com¬petitive tendering or contract awarding stage. In the near future, also the third fixed link of comparable extent, that is the crossing of the Fehmarn Belt between Denmark and Germany, will go into the decisive projecting stage prob¬ably in conformity with the aforementioned pattern. Going back to the Great Belt, it should be noted that this fixed link involves three exten¬sive sections and has been under construction since December 1988.

Jan 1, 1995

By S. N. McIntosh

Column bioleaching was evaluated by the U.S. Bureau of Mines as a means of recovering manganese from a low-grade ore from the Three Kids deposit in Southern Nevada. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms. Diluted molasses medium was provided as nutrient for the microorganisms. The medium was recirculated through the ore bed until the sugars were spent. Two methods were evaluated to recover manganese from the sugar depleted bioleaching solution: (1) adsorption with a weak cation exchange resin followed by stripping and precipitation techniques, and (2) direct precipitation of the manganese using ammonium carbonate. Both methods removed up to 95 pct of the solubilized manganese from the medium as a carbonate salt. After manganese removal, the medium was replenished with fresh molasses and recycled back through the column. More manganese was effectively leached. This process of manganese solubilization and recovery followed by replenishment and recycling of the medium was repeated until 98 pct manganese was extracted from the ore.

Jan 1, 1993

By H. H. Murray

Tactical R & D is research and development for a specific application or applications. The mineral scientist has to define and understand the physical and chemical parameters required for a specific or potential application. Then the researcher must know the structure and composition of the mineral and its physical and chemical properties. Can these properties be changed by processing particle size and shape modification, and surface chemical treatment? Examples of tactical R & D in the industrial minerals area will be described.

Jan 1, 2003

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By G. Pan

The production data of many mines have not reconciled geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metals are sometimes as large as 30%. A number of factors are responsible for such unpleasant outcomes. A major cause, however, is the lack of geological controls in the implementation of geostatistical techniques. Geological modeling establishes geological constraints and mineralization/ore envelopes. Geological constraints are usually established through drill hole interpretation. Mineralization and ore envelopes have been delineated manually based on assay grades. The issues associated with manual methods are: •Time requirements . •Inconsistent dilution. •Uncontrollable implementation variance. Although the time issue may not be a big concern for some companies, the other two have been responsible for many undesired estimation errors. A new geostatistical approach described in this study is designed on the basis of indicator and ordinary kriging. The central component of the method is the procedure for automatic delineation of mineralization and ore envelopes. The method, referred to as probability assigned constrained kriging (PACK), is demonstrated on a Carlin-type gold deposit. The estimation results are compared to blast-hole based production panels, showing that the estimated tonnage is about 2.1 % higher than the actual production, and the average grade is about 2.4% lower.

Jan 1, 1995

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By Robert J. M. Miller

Thank you Mr. Chairman. For more than 15 years a debate has been taking place among students of massive sulphide deposits as to the origin of these deposits. Prior that time it was widely accepted that the deposits were of hydrothermal, epigenetic and even replacement origin (Wilson, 14). Kinkel, Knight, Stanton and others advanced hypotheses which would explain the, formation of the deposits by different, largely syngenetic, volcanogeric processes. I was fortunate in having become involved in exploration for these deposits at about the time the debate was beginning and thus had an opportunity to apply with some success, some of the new and old ideas for formation of massive sulphide deposits. The deposits which I will discuss today are all located n northwestern Quebec, in the Abitibi orogenic belt. Mattagami Lake Mines is about 100 miles due south and Noranda's Horne Mine about 200 miles south of James Bay. In 1959 I prepared a talk which was presented to the 1960 CIM Convention calling attention to the spatial and possible genetic relationship between the ore sulphides of the Mattagami Area, Quebec and the tuffite, as well as the structures which controlled the ore. In this present paper I would like to cover the following points: (1) The general criteria used by the epigeneticists to support their contention that the deposits were formed after the enclosing rocks.

Jan 1, 1973

By S. Acar

The results obtained for the selective flocculation or flotation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is disscussed. Dissolved Fe, Cu and Ni species are found to affect the properties of chalcopyrite, pentlandite, millerite, pyrrhotite and covellite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation and complexation of species, etc.

Jan 1, 1985

By Howard J. Brown

The Lucerne Valley limestone mining district is in the San Bernardino Mountains, one of the major ranges in the Transverse Range Province of southern California. Several large limestone mining operations are present along the north range front in Lucerne Valley, and the area is one of the premier limestone mining districts in the country. Resources are contained in Paleozoic carbonate rocks that are part of a thick late Precambrian and Paleozoic sequence that uncomformably overlies crystalline basement. The district has been affected by multiple episodes of metamorphism and deformation, as well as by a complex sequence of late Cenozoic structural events. Detailed studies, however, have demonstrated that these rocks can be divided into formations correlatable with late Precambrian to Permian strata of the Cordilleran miogeocline. The district is the leading producer of white, high-purity calcium-carbonate products in western North America. Pluess-Staufer (California) Inc. mines and processes high-purity white limestone from extensive deposits, and is one of the largest producers of high-quality limestone fillers and extenders in the western United States. Major factors influencing the genesis of economic carbonate deposits in the district include depositional environment, post-depositional processes such as diagenesis, dolomitization and/or silicification, regional and/or contact metamorphism and associated intrusive activity, faulting, folding, uplift and erosion, and preservation from erosion. Regional geologic studies, detailed geologic mapping, intimate knowledge of stratigraphy, and recognition of complex structural relationships have proven to be invaluable tools in the discovery of high quality calcium carbonate deposits in the district.

Jan 1, 1987

By Kim Lapakko

As part of a project funded by the US EPA, through the Western Governors' Association, the recent literature on the prediction of acid drainage from metal mine wastes was reviewed. Static tests such as Acid Base Accounting, Modified Acid Base Accounting, B. C. Research Initial Test, and APP:S Test attempt to quantify the total capacities for a mine waste to produce and consume acid. In kinetic tests (e.g. humidity cells, soxhlet extraction, elevated temperature oxidation, column tests, batch reactor tests, B. C. Research Confirmation Test) mine waste samples are subjected to oxidation and the resultant drainage pH is assumed to reflect that of mine wastes dissolving in the field. This paper summarizes information presented in the recent literature on static tests.

Jan 1, 1992

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By F. M. Doyle, Robert G. Robins, E. Peters

Stability diagrams for the Cu-S-H2O system have been widely applied over many years. Stability diagrams for aqueous systems generally, have been generated by computer, but with the programs for Potential-pH diagrams in particular, a common routine leads to error in multi-element systems. In this paper these errors, and some misinterpretation of diagrams are considered. In most of the published diagrams for the Cu-S-H2O system there has been no account of the sulfide complexes of copper. Here, the free energies of formation for the various species in the system have been re-evaluated for consistency, and some diagrams for the Cu-S-H2O system ( generated with the program DIASTAB Vers.5 ) are presented.

Jan 1, 1993

By M. Z. Dogan, M. S. Celik, G. Onal, O. Ozcan, I. Yildirim

A fluorite ore (51.85 % CaF2) containing high contents of calcite, quartz and iron oxides was upgraded by flotation using a new reagent, oleoyl sarcosine (OS). In addition, quebracho and sodium silicate were used as depressants for calcite and quartz, respectively. The effect of pH, collector and depressants concentrations on grade and recovery was determined with the aim of optimizing the flotation conditions. Application of the two-stage cleaning achieved a concentrate assaying 92.17 % CaF2 with 80.1 % recovery. The Si02 content (0.76 %) was below the required level of 1 % SiO2. The mechanism of interaction between OS and fluorite, as compared to oleic acid, is also elucidated based on the zeta potential measurements.

Jan 1, 1993

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By M. Stefanakis, A. Kontopoulpus, K. Adam

The application of Bacterial Oxidation as a pretreatment step for the extraction of gold from the Olympias refractory pyrite concentrate is described. A wide review of Bio-oxidation is presented focusing on the current process developments and commercial applications relevant to the treatment of gold bearing sulphide ores and concentrates. Preliminary batch and semi- continuous tests on the Olympas concentrate indicated that with Bacterial Oxidation quantitative gold liberation may be achieved. fie effect of such parameters as pH, Eh, temperature, particle size, operating pulp density and retention time on the extent of sulphur oxidation and subsequent gold extraction by conventional cyanidation are also examined. Finally, a preliminary evaluation of Bacterial Oxidation as a potential process alternative for the treatment of the Olympias concentrate is presented.

Jan 1, 1989

By M. Jawed

Coking coal reserves in India are distributed geographically in Giridih, Raniganj, East Bokaro & Jharia Coalfields (J.C.F.). 97% of prime coking coal in JCF coming through underground mines is credited to Bord & Pillar mining systems inspite of the fact that it results in heavy mining losses. The cost of mining in B & P mines has been much higher due to various factors. In this paper, O.R. model has been discussed with case study for optimizing the cost of production in operational underground mines. Also, a computer algorithm has been discussed using a schematic flowchart, which provides the trend of mining-losses 'in different mining, systems with changing design parameters and finally selects, the optimum mining system for undeveloped seams based on economic appraisal criteria.

Jan 1, 1989