Search Documents

By Ronald R. H. Cohen, Margaret W. Staub

Two pilot scale bioreactors designed to treat acid mine drainage primarily using sulfate reducing bacteria were constructed underground at the Eagle Mine Superfund site in Minturn Colorado. The project was designed to test th applicability of microbiological treatment on water with high metals concentration and to test the process in an underground environment. Objectives were, 1) to compare metal removal, pH increase, and sulfate reduction in a single stage reactor with a double stage reactor of equal volume at varying flow rates; 2) to determine where within the substrate treatment occurs· and 3) to examine volume versus surface ara as a design parameter for optimizing metal removal processes. Results from the reactors showed that the single stage reactor and double stage reactor performed equally well for the removal of Cd, Cu, Pb, Fe, Mn, and Zn. pH increased above 6.5 in both reactors. Greater than 97% of metals were removed within the first ten inches of substrate. Volume proved to be a more useful parameter for determining removal rates than area. Using volume as a design parameter rather than surface area enables PMDT systems to be constructed as packed columns rather than broad wetlands, Thus, space requirements are significantly reduced.

Jan 1, 1993

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By Kathleen A. Altman

INTRODUCTION The basic premise of the ideas presented in this paper are as follows: Engineers believe that "theoretically" it will work. Operators ask what they must do to make it work. And, people can screw it up. r Today the challenges conf onted during the engineering, startup and operation of mines are becoming more complex. As mining and processing professionals, we are called upon to trav­el all over the world, are subjected to a wide variety of climates and must deal with a numerous cultures and people. Historically, for the majority of the people working in the mining industry, the primary challenges related to projects have focused on the differing perspectives of the disciplines involved. For example, geologists focus on resources and reserves, mining engineers relate to tons or tonnes, metallurgists count ounces or pounds or kilograms of product, mechanics emphasize availabil­ity, human resources personnel deal with absentee rates and turnover and accountants watch the bottom line ($$'s). As the world has become "smaller" and the mining industry has become more globalized, the puzzle is becoming increasingly difficult. Even the most experienced in the crowd of mining profes­sionals are oftentimes surprised by the types of problems that are encountered. Try as we may, we cannot anticipate the complex­ity of dealing with the human side of an operation.

Jan 1, 1998

By J. R. Dartez

The use of CCD (counter current decantat.io;1) thickeners, or; clarifiers, in the gold mining industry is quite common. Although there are a number of technologies in the industry which utilize these types of tanks, the fundamental requirement is to settle leach tailings and eventually separate gold and silver "values" from the "barren" (no values) solution. The thickener separation process varies depending upon the raw ores found in any specific mine. In mines where rudimentary, rocky ores are most common the settling process is fairly straight-forward and uncomplicated. But, for those mines with complex carbonaceous ores, usually identified by high silting, clay components, the ability to monitor and control the settled materials is quite laborious and costly. The task of monitoring and maintaining control of settled residue in clarifiers and thickeners, of any design, is difficult in any industry, but due to the added desire in the gold mining industry of leaching the values from the liquid slurry, the problem is multiplied. Other common activities taking place in the thickeners are exaggerated internal flow rates, settleable solids activity due to rake movement, and the settling activity generated by flocculents being added to the liquid medium. All of this action within the liquid column causes the continual monitoring of the interfaces within the tank close to impossible.

Jan 1, 1993

By Eugene F. Casey

As indicated on the official conference program, this presentation in not a formal one, but a synopsis of the activities of a newly created Sub-committee of the Research Council on Underground Construction, which involves itself with small diameter tunnels. Because there is a dire need to develop a system of excavating small horizontal openings at shallow depths without interrupting traffic, it was hoped that a more progress report could be reported at this time. Because of ecological and environmental considerations, laws are being passed which mandate that all utilities be placed underground. In urban areas the excavation of trenches in which these utilities are placed has been done by disrupting the normal flow of traffic, thereby creating complete chaos. In addition, it always seems that the Companies involved have no coordination, since one company completes its installation and another one begins. Certainly, utility tunnels can be driven at greater depths to house main feeder and trunk lines, but there still remains the problem of installing distribution lines for house services. The definition of a "mini" tunnel, is a tunnel whose excavated size is approximately 48 in. or less. The objectives of the Committee are to "stimulate the development of systems and equipment to build tunnels in these size ranges which will reduce costs, time and surface disruption from current systems."

Jan 1, 1974

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

By Jeffery L. Kohler

The characteristics of mine airstreams, such as their magnitude in the time and frequency domain and their spatial distribution, as defined by isovels, must be considered when making a measurement. The possibility for erroneous measurements is greatly increased when fixed- point sensors for mine monitoring systems are used. However, an a priori understanding of the airstream characteristics can be used to reduce the possibility of erroneous readings. This paper describes the problem, presents data to illustrate the nature of the problem, and provides recommendations for alleviating the problem.

Jan 1, 1987

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By Jon Kellar, Samuel Kessinger, Prasoon Diwakar

Tantalum (Ta) and niobium (Nb) are extracted from many different ore types. The major economic orebody mined for tantalum and niobium consists of tantalite ((FeMn)Ta2O5) and columbite ((FeMnNb2O5)) in a solid-solution mineral commonly referred to as “coltan.” The largest supplying region, The Democratic Republic of the Congo (DRC), is unfortunately also the most ethically compromised source for this critical mineral. Officially, the U.S. government has deemed coltan ore from the DRC a “conflict mineral” [1]. The lack of pragmatic and effective local mining regulation in Central Africa, when coupled with high levels of violence and corruption, has spawned a widespread, illegal, unethical and, most importantly, unsafe economy. This illicit economy is centered around first, illegally mining these valuable conflict minerals and second, smuggling these minerals into the global supply chain. Handheld spectroscopy devices could provide further transparency to these opaque supply chains, giving miners, traders and refiners the ability to authenticate the provenance of the minerals they encounter, and allowing companies to prove compliance with the regulatory agencies attempting to curtail illicit mining.

Mar 1, 2025

By J. Kemeny, R. Fuentealba, C. Rodriguez, F. Fernandez, M. Rocha, T. BoBo

"Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations. The goal of the mine is a mill throughput of 95,000 tonnes (104,720 tons) per day (TPD). Based on this goal, run-of-mine fragmentation analysis was conducted for four blasting designs resulting in powder factors of 0.44, 0.54, 0.64, and 0.94 kg/t. The powder factor of 0.44 represents a standard blasting design, while the 0.54 and 0.64 kg/t designs are high-energy blasts specifically to assist with mill production. The 0.94 kg/t design was investigated for the one geologic unit with very high strength. The results of the run-of-mine fragmentation analysis was then input into a crushing and grinding simulation model to predict the mill throughput for the time periods of 1-5 years and 6-10 years. The results indicate that certain blast designs are able to achieve the 95,000 tonnes TPD (104,720 tons TPD) goal, while other blast designs were not. A standard blast design with a 0.44 kg/t powder factor, for example, was not able to achieve the throughput goal, while a design with a 0.64 kg/t powder factor was able to achieve the goal in both the 1-5 and 5-10 year time periods. INTRODUCTION In recent years, mathematical modeling in conjunction with mineral characterization has been widely used as a method for the design and optimization of comminution circuits. The Run-of-Mine Particle Size Distribution (ROM PSD) is a function of rock properties and design parameters of the blast and has a significant impact on the crushing and grinding treatment circuit. Traditionally, design of the grinding treatment is estimated using only the F80 value instead of the full distribution of sizes in the feed, but the finer sizes have great influence on the treatment of a grinder, particularly in the SAG mill."

Jan 1, 2015

By Gary L. Simmons

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operations point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique mineralogical and chemical characteristics of the Lone Tree sulfide deposit that make it amenable to low temperature pressure oxidation. Problems encountered during pilot plant operation and their solutions are also discussed.

Jan 1, 1993

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By W. R. Reed

This study evaluates the roof-bolter canopy air curtain (CAC) system in an exhausting face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. Two scenarios are considered: (1) a roof-bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof-bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment that contains 6.0 mg/m3 of respirable dust and is ventilated by an exhaust curtain with 9,000 cfm (4.25 m3/s) of air to simulate the roof-bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8 percent. When the roof bolter is operated close to the face, increasing CAC airflow was required for adequate protection, as the dust reductions can be as low as 39.5 percent. Increasing CAC airflows to 350 cfm (0.17 m3/s) and 450 cfm (0.21 m3/s) were evaluated, demonstrating that dust reductions increased to 59.7 percent (350 cfm) and 72.0 percent (450 cfm). These results revealed improvement in respirable dust reductions compared to the CAC airflows at 250 cfm when the bolter is operated close to the face, showing the CAC can provide protection against high respirable dust concentrations for roof-bolter operators.

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the long wall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a long wall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

Jan 1, 1999

By Michael Robert Hodson

The views expressed in this paper are those of the author and do no necessarily reflect those of CRU. The Extent of Government Involvement In 1982 national governments in the Non-Socialist world owned at least some equity share in an estimated 49 percent of the bauxite mining capacity located in their own countries.* By comparison, as Figure 1 shows, in the same year governments owned at least part of an estimated 33 per cent of primary aluminium smelting capacity. In other industries, national, or state governments in 1982 held at least part ownership of mining capacity in 42 per cent in the copper industry, 34 per cent in the tin industry, 23 per cent of the zinc industry, 15 per cent of the lead industry and 11 per cent in the nickel industry. Thus while within the aluminium industry attention has focussed on the share of government ownership in the primary aluminium sector, national government involvement through ownership is larger in the bauxite sector. Moreover, ownership by government is more widespread in the mining of bauxite than in the mining of all other principal non-ferrous base metals. Yet while the equity participation of governments in the bauxite sector is widespread, it is but one of many forms of government involvement. In addition to direct ownership or equity participation domestic government involvement has taken the form of legislation to protect the environment, controls on the level of production, insistence on the export of ore, pressure to maintain levels of employment, controls on the type of fuel used, foreign exchange *Capacity which is owned in whole or in part is included within the state sector, but capacity in one country which is owned by a wholly or partly owned government company in another company is not included in the state sector; e.g. the capacity of the Trombetas mine is included in the state sector but the capacity of Delphi bauxite would not be included.

Jan 1, 1984