Search Documents

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10') M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By T. D. Maki

FMC Gold's Paradise Peak Mine, located 13 km (8 miles) south of Gabbs, Nevada, became operational in April of 1986. Shortly thereafter heap leach testwork began on sub mill grade ore. Presently, testwork continues in combination with production size heaps that account for approximately 6% of total gold production at Paradise Peak.

Jan 1, 1989

By Kalle Hakalehto

Automation and mechanization in mining has no value of its own. It has to be measured in economic terms or in Increased safety or in the utilization of deposits which otherwise were unavailable. The mechanization and automation of workphases in the mining and rock construction process has led to the decrease of manual work. This has had a very essential importance in the countries where the labor is expensive or where there has been difficulties in the availability of labor. The work has become much more efficient. We would like to argue that the need of mechanization has been initiated mostly from the above mentioned reasons. The origin has seldom been the "process" approach or the real need or will to change the way mining is done. Through mechanization bigger unit sizes of machines and operations have become possible and better efficiency is achieved. This has led to new problems as well, but in most cases they have been solved so that better and more economic outcome than before has been the end result. The changes have thus been justified. It is perhaps feasible to state already at this stage that we see that the mechanization andautomation steps in the difficult conditions of mining have been remarkable. There is not a slightest underestimation of the achievements and importance of this development in our mind. Where we are to- day is the result of the experience, know-how and technological excellency of all the parties involved. The natural approach to automation has been through mechanization and automation of individual unit operations and machines. This has been the way as well in manufacturing industry as in mining. There may not have been any other way. The other presentations in this session tell us very clearly of the approach .which the machine manufacturers have taken. They have not done it alone but 'most of the initiatives have come from them. A good use of their present achievements gives many possibilities to increase the, efficiency in mining. We would, however, like to extend the view one step further to the future:

Jan 1, 1989

By Martin Valeri

The operation described in-this paper will be confined to the Nemacolin Mine of The Buckeye Coal company, Nemacolin, Pennsylvania.' This mine is-located on the Monongahela River approximately sixty miles south of Pittsburgh. The mining is in the Pittsburgh seam that has an average thickness of 88 to 90 inches. The current practice is to mine approximately 80 inches, leaving 8 to 10 inches of roof coal. All of the coal produced is used solely for by-product coking by the parent Youngstown Sheet & Tube Company, Youngstown, Ohio. Eight to ten inches of top coal are left by the miners to prevent air slacking of the draw slate. In addition, this top coal which will float at the washing gravity has a very high ash and sulphur content, and when mined, seriously affects the quality of the clean coal product.

Jan 1, 1961

By Gaither H. Kitchell

Introduction Fire assaying is an ancient method of determining the amount of gold and silver in geological materials. Today's commercial, mining, school, and private fire assaying laboratories still use this basic assaying method. One of the primary reagents used to collect gold and silver from the ore is litharge (PbO), or lead oxide. The Federal Occupational Safety and Health Administration's (OSHA) and the Nevada Division of Occupational Safety and Health's (OSH) have a lead standard. It states that a person exposed to airborne lead at concentrations greater than 50 µg/m3 (1.4 µg per cu ft) of air over an eight-hour period has gone beyond the permissible limit for health safety. It is not uncommon to get airborne lead concentrations of 1400 µg/m3 (40 µg per cu ft) in the flux/sampling area or 900 µg/m3 (25 µg per cu ft) around the gas/ electric furnaces during the fusion and cupelling phases. Therefore, any individual working in these areas for more than 30 days per year without proper protection is a likely candidate for lead poisoning. Lead In A Human Lead enters the body as a toxic substance by breathing it into the lungs and upper respiratory tract and by getting lead particles into the digestive system through ingestion. Smoking, eating, drinking, chewing tobacco and gum, or wiping a lead-contaminated hand across the mouth are all potential ways forgetting lead into the body. Lead taken in large quantities can actually kill a person in a matter of days. This is rare, however. The real hazard of lead overexposure is for the unsuspecting person who works in an unsafe lead environment for months or years. This individual can slowly receive damage, sometimes permanent, to the central nervous system, gastrointestinal tract, kidneys, blood, gums, and reproductive system. Safe Blood-Lead Level The Lead Standard states that the maximum safe blood-lead level is 40 µg/100 g (40 µg per 3.5 oz) of whole blood. It recommends 30 µg/100 g (30 µg per 3.5 oz) if a person is of child-bearing age. People not working around lead products normally have a blood level of less than 10 µg/100 g (10 µg per 3.5 oz). A person not adequately protected can exceed 40 µg/100 g (40 µg per 3.5 oz) in a few weeks by fire assaying only 100 samples per day per week. Studies show that some individuals have developed lead-related diseases with blood-lead levels less than 80 µg/m3 (2.3 µg per cu ft). Lead Poisoning Symptoms There is a long list of symptoms associated with lead poisoning. The most common are: a prolonged, sweet, metallic taste in the mouth; loss of appetite; anxiety and irritability; weakness and dizziness; nausea and tremors; and insomnia. Preventive Measures Based on the lead standard, a number of preventive measures can be taken to ensure that fire assay laboratory personnel frequently exposed to lead are protected against overexposure. First, the actual lead concentration within the assaying area should be determined. In Nevada, one can contact the Department of Industrial Relations, Division of Occupational Safety and Health for assistance in monitoring any laboratory. The agency will also recommend ways to protect against lead. This agency does the monitoring and provides an educational class on lead safety. This type of agency can be found in other states. Commercial consulting firms are also available, but they are expensive. Regardless of the technique used to determine lead concentrations, it is most likely that the average fire assay area exceeds the 50 µg/m3 (1.4 µg per cu ft) lead concentration limit. This is considered unsafe.

Jan 8, 1985

By M. Rieber

In July 1985, as the U.S. copper industry contracted and the Mexican industry expanded, a trans border pollution agreement was signed which included smelter air pollution control in the "Gray Triangle": Cananea, Nacozari and Douglas. Since then the Douglas smelter has been closed, a year earlier than initially required; though its new smelter is operating, S02 collection and acid disposal at Nacozari is yet to come; and the Cananea smelter has been un-touched. Nacozari and Cananea copper mining have expanded while a reduced U.S. copper industry has rationalized to a point of fragile profitability. As a paradigm of U.S. copper competitiveness, this paper attempts to explain the differential fortunes of copper in the two countries, to project the future of the smelter agreement as a function of acid disposal, and to consider the consequences of the politicized application of smelter pollution control in Arizona.

Jan 1, 1988

By D. N. Thompson, R. L. Sayer, K. S. Noah

Economical remediation of acid rock drainage (ARD) at secluded high-altitude western ore mines is difficult given the current treatment technology. Several passive-engineered systems that are based on wetland technology were tested in the laboratory with three western ore mine ARDs (Co, Cu and Fe mines) and with a copper leachate effluent. These systems used well-weathered lodgepole pine sawdust as the sole carbon source and mud from a pond at one of the mine sites as the source of sulfate-reducing bacteria (SRB). Simple one-pass flow-through systems removed 44% to 99% of the vari¬ous heavy metals front the Co and Cu mine ARDs and increased the pH from 3 to 7 after 28 days of SRB acclimation with a five-day residence time. Carbohydrate utilization rates were generally low, except for one 437-day run, which consumed 25%, 30% and 21 % of the cellulose, hemicellulose and lignin, respectively. Initial pH, amounts of toxic heavy metals and the degree of predegradation of the sawdust were found to significantly affect both remediation potential and acclimation time. Engineered SRB systems, alone or in combination with other passive technologies, offer promise for the economical remediation of western US ore mine ARDs.

Jan 1, 2000

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By Fred N. Kissell, Jeffery L. Kohler, Edward D. Thimons

Aerodynamic stall of vane-axial fans is both an operational problem and a safety concern. While deep stall is relatively easy to detect, the diagnosis of a partial stall is often more difficult. Its transient nature and the fact that its symptoms can mimic electromechanical problems of the fan and fan drive assembly, or vice-versa, compound the difficulty of making a timely and accurate diagnosis. A knowledge-based expert system known as FANPRO has been developed to aid in the diagnosis of these problems. FANPRO and its application are the subject of this paper.

Jan 1, 1991

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

During 1993, contraction of indus¬trial economies in Germany (-2%), France (-1 %), Japan (-0.1 %), Eastern Europe (-2%) and the former Soviet Union (-13%) dimmed prospects of a robust economic recovery for North America. Some European countries that suffer from high unemployment and large government deficits have non-com¬petitive cost structures that will require long-term economic reforms to solve. Restructuring in the United States also continued in 1993. The sluggish pace of the US economic recovery, in¬troduction of federal tax increases and the persistence of high levels of unemployment did little to inspire consumer confidence. By the end of the year, however, sales of consumer durable and capital equipment began to grow. Depressed demand for minerals by industrial economies in recession was partially offset by continuing rational¬ization or abandonment of non-competi¬tive productive capacity in Eastern Eu¬rope and the former Soviet Union. Al¬though aluminum, lead, titanium sponge and zinc prices fell, increases in copper and steel consumption helped steady their prices along with prices of some alloys. Cash flow to the mining industry - the primary source of exploration funds - was therefore constrained. For many companies, exploration expendi¬tures were reallocated geographically and in terms of commodities sought.

Jan 1, 1994

By H. V. S. Tingley

My topic today is future trends in compensation for the mining industry. I seldom get the chance to speak about a subject of such immediate interest to an audience, so I would like to make the most of this opportunity by telling you that everybody in this room will become rich beyond his wildest dreams in the next few years. I would like to open my talk that way, but in compensation, like everything else, there is a great gap between dreams and reality. Back to reality. When we talk about compensation, we?d better define our terms because the compensation is really an umbrella for five basic types of payment made to management personnel. Slide 1 identifies these elements of compensation.

Jan 1, 1980

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By K. Irmscher

During the last years, using modular computer models on the software and distributed computer capacities on the hardware side has become quite common in the mining industry. When tackling real mining problems under the condition of heterogeneous systems, however, some problems become obvious: the incompatibility of the heterogeneous platforms in connection with the heterogeneously structured information and the necessity of interpreting the data. Knowledge based approaches are employed for solving different planning problems in the field of mining industry. The main problems here consist in the knowledge representation and data acquisition. Starting point of the investigation form classifications of mining planning problems and the corresponding models which can be transformed into information models for evaluation. With help of an expert system a practical solution is represented. Distributed systems with mobile computing and communication facilities for immediate access can be used as an additional support for planning and processing. On the base of public or private computer networks (including mobile networks) the foundation is given for a computer supported treatment of planning tasks. Additionally the use of teleworking scenarios in regions of mine planning and data collection in geological applications is prepared. Foundation forms a workflow system on an object-oriented distributed platform.

Jan 1, 1996

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro, NC, treating crude Waelz oxide (WOX) to produce special high-grade zinc by a hydrometallurgical process comprising leaching, zinc solvent extraction/electrowinning, melting and casting and bleed treatment. Cadmium removal by zinc-dust cementation plays an essential role in the bleed treatment circuit to prevent cadmium buildup in the circuit. Silica, though present at a low level of approximately 0.3 percent in the WOX feed material, had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also affected. To identify the source of the silica issues, silica levels were mapped throughout the circuit, and adjustments, including using pregnant leach solution as the feed to cementation, and pH control in the WOX leaching and neutralization were introduced to mitigate the issues created by silica gel in the circuit. IntroductionLocated in Mooresboro, NC, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz oxide (WOX) to produce special high-grade (SHG) zinc. The flowsheet, known as the Modified Zincex process, consists of leaching, solvent extraction (SX), electrowinning (EW), melting and casting and bleed treatment (Fig. 1). Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press.At the refinery, WOX pulp is leached at a controlled pH to achieve the maximum zinc extraction, according to the main reaction:"

Jan 1, 2016

By H. Y. Sohn

The paper discusses two processes, flash ironmaking technology (FIT) and moving-bed ironmaking technology (MBIT), which aim to reduce energy consumption and greenhouse gas emissions in the ironmaking industry by using concentrate directly without pelletizing and without using coke.

Aug 1, 2023

By F. A. Campbell

This paper reports on mineral facies, ore textures, distribution of iron in sphalerites, and fractionation of sulfur isotopes in the Anvil ore body, Yukon Territory, Canada. Because the detailed structure and stratigraphy, both regional and local, are being studied by the geological staff at the mine and members of the Geological Survey of Canada, these topics will be discussed only briefly. The results of our study of the Anvil ore body have implications on theories of the genesis of ore deposits of this type, and these will be discussed. The Anvil ore body is the largest and most significant of three lead-zinc discoveries in an area of the central Yukon where major lead-zinc deposits were unknown only twenty years ago. The Vangorda deposit consisting of 22 million tons was discovered in 1953, followed in 1954 by the Swim Lakes deposit consisting of 10 million tons. The Anvil deposit, which consists of three ore zones, was discovered in 1964. The total reserve at Anvil mine is 63.5 million tons, with an average grade of 3.4% lead, 5.7% zinc, 0.16% copper and 1.2 ounces of silver per ton. This study is concerned primarily with the number one ore body which is about 2,400 feet long, up to 1,100 feet wide and 300 feet thick.

Jan 1, 1973

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"INTRODUCTION Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito Operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Open pit mining (pre-stripping) began in 2010 and full production commenced during 2011. The open pit mines feed both a sulphide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp, Inc. Penasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals. As a consequence of lower grade ores expected with advancing mine-life Peñasquito is facing a declining metal production profile. To maximize returns and asset value plant modifications including the addition of a carbon pre-float circuit and a pyrite leach circuit to improve recovery are currently being undertaken. This carbon pre-float circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Penasquito operation. The addition of the carbon pre-float circuit was also a key driver in allowing the Chile Colorado open pit to be developed. These conditions alongside Goldcorp’s drive to increase profitability, and maximize net asset value has created challenges. These challenges are numerous and are multifaceted, however the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this paper and include improvements in geo-modeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance, and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 1, 2018