Search Documents

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By W. A. Weimer

Coal and coal mining is no longer the mighty king of industry and in our daily lives and homes that it once had the privilege of commanding. Many of you will remember that one of the chores of your youth was to bring in the scuttles of coal, morning and night, to feed the heater or stoke the furnace in the morning and bank it at bedtime. Growth of gas and oil have displaced coal in home furnaces and commercial buildings, and have taken over some segments of industrial markets. The coal burning locomotives have virtually disappeared in favor of the more efficient diesel engine. However, coal as a prime mover still holds its strategic position as is evidenced by act that the electric power industry almost entirely depends upon coal for its generation.

Jan 1, 1961

By D. G. Krige

In the world mining scene, precious metals (particularly gold) have recently monopolized the attention in exploration as well as new production activities. As the major world producer of gold, South Africa plays and will continue to play a very significant role in this commodity. This role will, of course, have its consequential effects on the world's gold supply and, hence, also on the international price of gold. It is essential, therefore, and in the interests of all gold producers that the likely future pattern of gold production in South Africa be estimated such that some measure of production uncertainties can be predicted. For this purpose, some elementary geostatistical models will be used, and the main factors affecting the situation will be analyzed in broad outline only under the following headings: South Africa's basic gold ore potential in the three categories of: (1) ore remaining in existing mines; (2) extensions to existing mines via unexplored areas and/or reef horizons of lower grade; and (3) new mines, potentially deep or ultradeep. Cutoff grades - operating, marginal, and flotation, for the foregoing three ore categories, respectively. The availability of production, financial, and other resources required. Cutoff grades will, of course, depend on cost levels (operating and capital), future inflation and cost escalation trends in South Africa (SA), and/or gold price trends (in US$ and via the exchange rate in SA Rand terms). The differentials in inflation and escalation trends with those in overseas countries, mainly the USA, will, in general, set the scene for future exchange rate levels of the Rand. To predict the effect of various cutoff grades on future gold production from South Africa, it is essential to use geostatistical models. The applicability of such models is tested against past records of price, cost, and grade trends and then applied to the estimated ore potentials. These models were referred to briefly in a paper at a recent seminar on gold (Krige, 1986) but are discussed in detail herein. This lecture was intended originally to cover only technical aspects, but, in view of South Africa's position internationally and the possible effect of sanctions, internal unrest, and strikes on gold production, a brief reference to the third factor above (availability of production, financial, and other resources) seems appropriate.

Jan 1, 1988

By Martin N. Kelley

The Great Belt Link is a $3.5 billion fixed link across an 18 km (12 mile) wide body of water that separates the island of Zealand, on which Copenhagen is situated, and the main land mass of Denmark, Jutland, which is part of the European continent. The project consists of three main contracts. The first contract is an 8 km (5 mile) long, two-bore railway tunnel for the eastern half, the second contract is a 6.6 km (4 mile) combination railroad and highway bridge for the western half, and the third contract is a 6.7 km (4 mile) long high-level highway bridge for the eastern half. This paper will discuss the Eastern Railway Tunnel Project and the methods of construction that the joint venture consortium plans to use, along with its equipment selection. The ground conditions to be encountered begin with glacial tills, which are a mixture of clay, silt, sand, gravel, cobbles, and granitic boulders. The boulders can be up to 1-3 m (3-10 ft) in diameter. Underlying the till is a marl which is sometimes highly fractured with hydrostatic pressures of up to 8 bar. About 40% of the tunnel is in till and 40% in marl, with the remaining 20% being a mixed face of the two formations.

Jan 1, 1991

By Jorma Miettunen

The Plant. The annual production of the Pyhasalmi mine is 900 000 tons of copper- zinc-pyrite ore containing approximately 0.7 % Cu, 2.5 % Zn and 30 % S. During 1976...1981 altered surface ore, 850 000 tons in all, was also treated at the concentrator. The surface ore was crushed and ground in a separate plant and was then fed into the copper or zinc flotation or was flotated in its own circuit, depending on the degree of alteration and the content of copper and zinc in the ore. The surface ore was exhausted in October 1981. Flotation comprises three consecutive flotation circuits; copper, zinc and pyrite circuit. The zinc circuit includes an open circuit roughing and scavenging. The scavenger concentrate and cleaner tailing are pumped to the middlings flotation. Rougher concentrates of the open circuit and the middlings flotation are pumped to cleaning which includes four stages. Figure 1 describes the flowsheet of the zinc circuit.

Jan 1, 1982

By A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom-fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three polymeric conditions which were cationic polymer, anionic polymer, and a combination of cationic-anionic polymer. For each polymeric condition, two mathematical models were developed: one for overflow response, the other for underflow response. The combination polymers produced the best desired quality of overflow and underflow. For this polymeric condition, changes in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of the underflow quality. The mathematical models generated a set of plots which would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1989

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By Yi Luo

A massive roof fall occurred in a small room-and-pillar coal mine. The roof falls occurred under a barrier pillar in a closed coal mine located a short distance above the active mine. The extensive fractures connected the active mine with the old mine, turning them into a “combined mine.” Since completely sealing off the roof fall area is prohibitively expensive for the mine, ventilating the connected old mine became the only option. A comprehensive investigation was conducted to understand the atmospheric condition in the old mine and to find an efficient way to ventilate the “combined mine.” A set of studies involving geology, gas content, pillar stability and mine subsidence were performed to explore whether the closed mine is filled with an explosive air-methane mixture. The air quantity measurement data were used to determine the resistance of the air path formed through the fractured zone. Observations and measurements made from a tour to the underground and mine surface enabled the formulation of simple but effective ways to ventilate the old mine. The ventilation network analysis also suggested methods of control, so that sufficient ventilation air can be directed to the two parts of the old mine.

Jan 1, 2010

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By Theodore H. Eyde

The porphyry copper province of the southwestern United States and northern Mexico, is the largest copper producing region in the world. Most of the deposits occur in Arizona which now produces over 54% of the newly mined copper in the United" States. As the many recent discoveries are brought into production, Arizona's share of the nation's copper production will increase. The term "porphyry copper" as used in this paper includes all deposits of generally low grade disseminated copper mineralization amenable to bulk mining techniques. Therefore, copper deposits such as Pima-Mission, Twin Buttes, and Vekol where the copper mineralization occurs principally in the intruded rocks will be considered as "porphyry copper" deposits. Most of the deposits have been discovered since World War II, consequently, the southwest, and particularly southern Arizona is perhaps the most intensively explored area for copper deposits on earth. Most of the major natural resource companies in the United States and Canada maintain exploration offices in southern Arizona. To illustrate the success of exploration efforts, the location of porphyry copper deposits either known or producing prior to World War II are shown on figure 1 and the deposits discovered since World War II which are either in production or in the exploration and development stage are shown on figure 2.

Jan 1, 1973

By Erich U. Petersen

Chemical zoning studies of mineralization can be useful in guiding exploration efforts. They permit one to determine the limits of mineralization and to correlate mineralized intervals in drill holes. Fahlore minerals are well suited for zoning studies because they are common minerals found in a variety of deposits, exhibit chemical diversity, and record the chemical evolution of migrating hydrothermal fluids. Zoning information in the form of metal ratios preserved in fahlore minerals was used to determine ore body limits in the Orcopampa precious metal system, Peru, and to correlate between multiple ore horizons in a sediment hosted massive sulfide (SHMS) currently under investigation. The current generations of electron microprobes provide the most efficient, accurate and economic way to analyze the tens to hundreds of sample required to successfully describe and use zoning information at the mine scale.

Jan 1, 1991

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

A study was conducted in an undergroundminewith the objective to identify, characterize, and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. The focus was on contributions of diesel- and battery-powered heavy-duty vehicles used to transfer equipment between the depleted and new longwall panels and diesel-powered light-duty vehicles used to transport personnel and materials to various locations within the mine. Aerosols at the setup face were found to be distributed among diesel combustion-generated submicrometer and mechanically generated coarse aerosols. According to the data, the submicrometer aerosols downstream of the setup face were sourced to diesel exhaust emitted by vehicles operated inside and outside of the panel. Depending on the intensity of the activities on the panel, the outby sources contributed between 12.5 and 99.6% to the average elemental carbon mass flow at the setup face and recovery room. Extensively used light-duty vehicles contributedmeasurably to the elemental carbon concentrations at the setup face. The number concentrations of aerosols downstream of the setup face were associated with aerosols generated by combustion in diesel engines operated in the shield haulage loop and/or outside of the longwall panels. Entrainment of road dust by diesel or battery-powered load-haul-dump vehicles operated near the measurement site appears to be the primary source of mass concentrations of aerosols. The findings of this study should help the underground mining industry in its efforts to reduce exposures of miners to diesel and coarse aerosols.

Apr 14, 2020

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By M. Karmis

According to international projections and future energy scenarios, coal will continue to be a prominent fuel for the next 25 years. In fact, in many regions around the world, coal is expected to dominate the electricity sector until the year 2030. At the same time, with instability and volatility of oil prices, coal is also positioned as an alternative feed stock for conversion into liquid fuels. Energy economists maintain that coal liquefaction is viable at crude oil prices of $35 or more per barrel. Depending on technology and coal composition, 1 ton of coal can produce 1 to 4 barrels of oil. Increased coal production and the expanded utilization of coal also raise environmental concerns regarding greenhouse gases and the problem of handling CO2. Carbon sequestration research, currently conducted in many parts of the world, has demonstrated considerable potential for C-storage in unminable coal seams. Such geologic storage, when possible, can also be integrated into an enhanced coal bed methane recovery process Can coal fuel power plants and industrial facilities, provide diesel and other liquids and, at the same, also be used as a medium for permanently storing CO2? This presentation will provide a global perspective on these questions and stress on the need to reconsider, or even redefine, coal as the fuel for the future.

Jan 1, 2006

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012