Search Documents

By G. J. Hartman

A presentation of this project was given previously at the SHE Annual Meeting, Denver Colorado February 23-27, 1987. The project concerns the development of in situ recovery of borate products from a deep-seated colemanite deposit in California. The deposit contains some 147 million tons of borate ore containing 6.4% boron oxide (B2O3). This paper involves the numerous changes in the process that has taken place since that first presentation. This paper further explains the reasons for these changes which are primarily environmentally based and secondarily capital requirements related.

Jan 1, 1994

By C. D. Kuchera

Ore crushing facilities at the Phelps Dodge Morenci Reduction Works became operational in January of 1942. This plant, with a capacity of 25,000 tons per day, was part of a project started some five years earlier with development of the Morenci Open Pit Copper Mine. In the following year, World War II's heavy copper demands prompted an 80% expansion in concentrating capacity to 45,000 tons per day resulting in a doubling of the secondary crushing plant. In the late 1950s and early 1960s, grinding capacity was again expanded to the present 60,000 TPD. This time the then 20 year old crushing plant was obliged to meet a 20% increase in production demand with no additional equipment. The ore, principally a medium hard monzonite porphyry, is dumped from 40 yard rail cars into an ore pocket over the primary crusher at a rate of approximately one car per minute. The primary crushing flowsheet, Figure 1, has remained essentially unchanged over the years. Equipment consists of a 40 by 16 foot grizzly set on a 40° incline and having 6" openings, a 60" gyratory crusher nomin¬ally set at 62" + 1" on the closed side and two 72" by 38' panfeeders which load crushed ore and grizzly undersize at a rate of 4,000 tons per hour onto a twin 54" belt conveyor system for delivery to the coarse ore bin. Ore is distributed across the bin by two single side discharge tripper cars. Bin capacity is extremely limited at 23,000 tons of which only 12,000 is available or "live".

Jan 1, 1975

By Ahmed Alghamdi, Salem AlGharbi, Aisha AlHarbi, Owain Morton, Norah AlMuhaisen

This paper addresses the challenges in optimizing the phosphate flotation process, specifically focusing on the variability in P2O5 recovery. An artificial intelligence (AI) driven Flotation Prediction Model was developed to accurately forecast P2O5 grades. Leveraging real-time data from various operational sources, the model provides insights into how operators can opstimize key flotation parameters to enhance product quality and recovery rates. The results demonstrate the effectiveness of AI predictive modeling in addressing operational variability, marking a crucial step toward intelligent operations in the phosphate flotation process.

Feb 1, 2025

By T. Glenn Pobanz

For more than fifty years Walter Kidde & Company, Inc. has engaged in the development and manufacturing of both fire suppression and detection equipment. Our initial work for the mining industry centered around dry chemical extinguish-ing equipment for mine haulage cars. To fulfill this need, Kidde engineered and developed a manually activated dry chemical system to provide protection for the wheel wells, cable reels, and motor compartments on various pieces of underground mining equipment. The next phase of mining operation fire protection for Kidde was the area of detection and automatic fire suppression for conveyor belt heads. Early in 1970, a field evaluation program and belt head demonstration unit was taken to 10 areas throughout West Virginia, Kentucky, Pennsylvania, and Ohio. This extensive field program was a joint effort with National Mine Service Company of Pittsburgh, Pennsylvania. The objectives of this program were to study mine hazard problems and to determine further requirements of mine operators. The resulting belt head detection system centered around our Continuous Strip Thermistor Core heat detector in conjunction with a Kidde stored pressure dry chemical extinguishing system. Continuous Strip detection has been in use for a number of years in aerospace applications. It has proven flexible and reliable for the rapid detection of overheat conditions and fires in engines of over half the aircraft flying today. The use of Continuous Strip gave us flexibility to protect surface areas over and around the actual conveyor belt head equipment. The nature of Continuous Strip allows us to bend, wrap, and attach the 20 foot long thermistor element over the desired protected points of the belt head. An integral part of the conveyor belt head protection system is the control panel utilizing our comprehensive knowledge of fire alarm control logic. This panel contains supervision circuits which sound trouble signals upon detecting a break in the Continuous Strip; breaks in the wiring to the remote electrical extinguishing activators or to the alarm bell; or loss of primary power. A separate control module provides the adjustable alarm temperature setting of the

Jan 1, 1971

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By Richard Jr. Ray, David Johnston, Phil Blankenship

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1989

By William H. Dresher

The crust of the earth, together with its seas and its atmosphere, is the source of all of mankind's primary wealth. Indeed, most people think of precious metals and stones when they think of wealth mined from the earth, but the value of the material and energy goods derived from the earth far exceed the value of the precious metals and gem stones. Thus, it is obvious that all minerals which we mine from the ground represent new wealth--the copper, clay, or petroleum we mine just as much as the gold or silver. More and more, wealth is defined in terms of utility-not in terms of an arbitrarily established monetary value. The recent action of the OPEC nations in controlling the flow of petroleum has clearly demonstrated this to the petroleum-importing nations! There is developing in the United States, as well as in many other nations of the world, a concern for the future availability of many mineral-derived raw materials and of mineral fuels. Ore grades are diminishing, concern for the environment has placed restraints on commercial development of some mineral deposits and the processing facilities necessary to exploit them, and countries upon which we have relied for major mineral materials have become increasingly nationalistic, causing uncertainties in future supply and causing an increasingly alarming deficit in our nation's balance in trade.

Jan 1, 1980

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the roof bolter canopy air curtain (CAC) designed by the U.S. National Institute for Occupational Safety and Health (NIOSH) has gone through many iterations, demonstrating successful dust control performance under controlled laboratory conditions. J.H. Fletcher & Co., an original equipment manufacturer of mining equipment, further developed the concept by incorporating it into the design of its roof bolting machines. In the present work, laboratory testing was conducted, showing dust control efficiencies ranging from 17.2 to 24.5 percent. Subsequent computational fluid dynamics (CFD) analysis revealed limitations in the design, and a potential improvement was analyzed and recommended. As a result, a new CAC design is being developed, incorporating the results of the testing and CFD analysis.IntroductionExposure to respirable coal mine dust can cause coal workers’ pneumo-coniosis (CWP), also known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is to eliminate exposure to respirable coal mine dust and crystalline silica, or quartz. The occupational exposure limit on a Mining Research Establishment (MRE) basis for respirable coal mine dust had been 2 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities. Under recently enacted legislation, this standard was changed in August 2016 to 1.5 mg/m3 for a full working shift (The Office of the Federal Register, 30 CFR 70.100, 2015). When respirable quartz is present, the mine must maintain its average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percentage of quartz present (The Office of the Federal Register, 30 CFR 70.101, 2015).The sources of exposure to respirable coal mine dust for roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind — in the return air — of the continuous miner (Good-man and Organiscak, 2003). Recent studies have demonstrated that vacu-um dust collection systems are effective in capturing bolter-generated dust if maintained and operated correctly and if proper face ventilation techniques are used. However, most expo-sure to respirable coal mine dust for a roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner (Potts, Reed and Colinet, 2011; Colinet, Reed and Potts, 2013). Because of this higher exposure downwind of the continuous miner, the roof bolter is often limited to working downwind of the miner only once during a production shift."

Jan 1, 2017

By X. Cheng

The mechanism of cathodic decomposition of pyrrhotite was studied in deoxygenated solutions at natural, near neutral pH using potential and cyclic voltammetric measurements. Reaction products on pyrrhotite surfaces were examined by AES and XPS, and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by micro-flotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1993

By Jamal Rostami, Alireza Salimi, Christian Moormann

"Rock mass classification systems are often applied in many empirical design practices in rock engineering, some contrasting with the original intent and applications of these classification systems, for example, estimation of TBM performance in various ground conditions. While accurate estimation of machine performance is significantly impacted by rock mass properties, parameters used in many of the existing classifications are more related to ground support design and not rock mass boreablity. The results of many investigations on this issue have shown a weak correlation between TBM rate of penetration and rock mass classification. This limitation can be overcome by fine tuning the rock mass classification input parameters to represent influence of rock mass properties on TBM performance as has been the objective of RME or QTBM. This paper will offer an overview of the impact of rock mass on TBM performance and introduces an empirical equation for predicting performance of rock TBMs based on rock mass classification. The results of the preliminary analysis of a new model has revealed that the use of the proposed system can offer a reasonable accuracy for estimation of TBM performance in various rock masses. 1. INTRODUCTION Hard rock tunnel boring has become more or less the standard method of tunneling for tunnels of various sizes with lengths over 1.5–2 km. Estimating the performance of TBM is a vital phase in tunnel design, and for the choice of the most appropriate excavation machine. During the past three decades, numerous TBM performance prediction models for evaluation of TBM rate of penetration and advance been proposed. In brief, all the TBM performance prediction models can be divided into two distinguished approaches, namely theoretical and empirical ones (Rostami et al., 1996). The most common and recent works on this topic are summarized in Table 1. Currently, two models including Colorado School of Mines or CSM (Rostami and Ozdemir, 1993; Rostami, 1997) and Norwegian University of Science and Technology or NTNU (Blindheim, 1979; Bruland, 1998) models are the most recognized TBM performance prediction and prognosis models in use around the world."

Jan 1, 2016

By W. J. Nelson

Detailed underground geologic map- ping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Company, which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium- to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular-bedded limestone, and (4) fine-grained, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sand- stone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults of small displacement, "slips" and clay dikes, and limestone "bosses." Less stable roof and wet con- ditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that inter- sect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural patterns apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof sup- ports. Drilling also is useful In locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1980

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By Wayne C. Smith

Both water pollution and proposed solid waste disposal regulations have a definite effect on the copper leaching industry and some of the major factors affecting the industry are discussed in this paper. New developments of the NDPS are discussed with emphasis on the "toxic" or priority pollutants and EPA's philosophy on the control of these pollutants, The protection of groundwater is the prime aim of RCRA through solid/hazardous waste management. Some of the major elements of the RCA regulations that will affect the copper leaching industry are discussed.

Jan 1, 1980

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By T. D. Barkand

A recent coal mine elevator accident resulted in serious injuries to four passengers. The miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. In response to mine hoisting accidents, safety authorities have required additional protective devices on new and existing mine hoists and elevators. This paper examines supplemental safety circuits and new devices designed to provide ascending car overspeed protection on mine hoists and elevators. These devices provide needed protection that eliminates the hazard or significantly reduces the potential of a mine hoisting accident.

Jan 1, 1995

By J. B. Goddard

Abstract. Leaching of, uranium in situ from sandstone deposits with ammonium carbonate solution containing: dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However because of their high reducing, capacity and their relative abundance, the FeS2 minerals consume; the bulk of the oxidants A pressure leach apparatus was-construtted which permitted the measurement of oxygen consumtion by FeS2. Oxygen consumption by FeS2 is best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1980

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018