Search Documents

By Sukumar Bandopadhyay

In recent years, research in the field of artificial intelligence (AI) has had many important successes. Among the most significant of these has been the development of powerful new computer software known as the "expert systems". Expert system programs designed to provide expert-level consultative advice in mineral exploration (Duda et al, 1981), scientific (Feigenbaum, Buchanan and Lederburg, 1971) and medical (Shortliffe, 1976) problem solving are generally acknowledged to be among the forerunners of this research. As the decision makers virtually in all fields face a more complex and involved world within which to operate, the need for some decision support is also becoming urgent. Thus applications of expert systems continue to spread out reaching problems that, because of their dimensions or particular aspects, set more demand on the decision methodologies. To meet these new requirements, many activities which were performed in the past by the domain expert or engineer must become automated. Furthermore, previous research (Dawes and Corrigan, 1974; Dawes, 1979) has shown that automating an expert's decision rules often provide better decision than the expert does. For large systems it would be very useful (or even necessary) to have formal tools, allowing one for example, to automatically discover inconsistencies, contradictions or redundancies, or to identify the possibilities of wrong lines of reasoning in the decision process.

Jan 1, 1990

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By Newell H. Orr

Titanium's performance characteristics in acidic oxidizing and mildly reducing environments make it applicable to numerous currently defined and many projected hydrometallurgical applications. With titanium's current and projected availability and price stability increased use in pressure leach, piping systems and electrorefining is practical.

Jan 1, 1983

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province's mines. Fining layouts, materials handling and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1980

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By A. Venkatachalam

Spinel ferrites, like NiFe2-2x Znx Ti4 O4 Fe CO1.5 Ge0.5 Tix O4, Ga1-x Fex Ni CO O4, Nil-x Fex Mn2 O4 have been prepared using the respective metal oxides in Stoichiometric quantities, by the ceramic method. The oxides were homogenized in acetone medium, pelletifed by using poly vinyl acetate as the binder. They were fired at 1000°C for 100 hours for compound formation. Chalcogenide spinels such as Zn1-x Cux Cr2 Se4 where 0=x=l and Cu1-x Fex Cr2 Se4 where 0=x=0.3 have been prepared by using 99.99% pure elements and then fired at 1000°C in quartz ampoules under vacuum conditions. X-ray diffraction studies of these compounds indicated a single cubic spinel phase. DC resistivity studies of the compounds were taken between 300-700K using LCR bridge by two probe technique. Thermo-electric power measurements were taken between 300-500K for all the compounds. Initial susceptibility studies have been carried out using a low field (0.506) and from which the nature of magnetic dimains and Curie temperatures were determined. Magnetic hysteresis measurements were carried out at 300K and at 80K, using alternating current hysteresis loop tracer, at 2K02 field. Mossbauer spectral measurements were carried out using Co57 source embedded in a copper matrix and an absorber containing 0.3 mg/cm2 of the sample. The spectra has been fitted by Mossfit Program. The catalytic effect of the spinel ferrites NiFe2-2x Znx Tix O4 where 0=x=1 has been studied by using the model reaction of decomposition of H2O2 at temperatures from 40°C to 70°C. It was found that the spinel oxides were found to possess poor catalytic activity.

Jan 1, 1990

By R. L. Grayson

The health and safety of employees, efficiency of the operating system and production are paramount goals in underground coal mining. The section foreman assumes responsibility for making his part of the total system function to meet these goals. However, section foremen often have not been prepared to assume the full range of their responsibilities upon becoming a supervisor. This discussion addresses the full range of section foreman responsibilities and concomitant authority. Management principles that must be mastered by him are presented, and performance expectations as well as criteria for their evaluation are examined. The benefits realized from effective foreman training are discussed.

Jan 1, 1985

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

By Randal J. Barnes

A system, such as a mine production system or a mine ventilation system which includes the movement of commodities or some material between decision points may, in many instances, be effectively modelled as a network. Mining has often been characterized as primarily a materials handling function. To a great extent this is true, even though it is an over simplification of all the activities involved in a mining operation. Accepting the materials handling characterization of a mining operation permits the extension of the characterization to a flow process. That is, the ore flows from the mining face through the mining phase (excavation & loading, hauling, dumping) through the milling phase (crushing, grinding, recovery) through the smelter phase and finally to marketing. With this concept it is possible to depict a mining operation as a simple network. For example consider an operation consisting of two mines (A and B) with mills at each mine (MA and MB) with the possibility open to treat ore from mine b at mill NB, but it is not feasible to treat mine B ore at MA. The product of both mills is sold.

Jan 1, 1983

By H. A. Zollinger

The Hallmark Distribution Center is one of the most sophisticated material handling and order filling facilities in the world. The 53 million cubic foot facility houses an ultra-modern, computer- monitored distribution complex that handles as many as 1/4 million orders per day. The Distribution Center replaces 16 leased buildings scattered through- out metropolitan Kansas City and, in addition, re-leased 4 floors in mid-town Kansas City needed for creative and administrative expansion. This new facility is the nerve center for distribution of Hallmark products in United States and Latin America. The size and gross numbers of all parts of the system is a significant accomplishment, but the purpose of this paper is to explain the technical advancements in the state-of-the-art of material handling and controls. The system iteself is made up of seven sub-systems including receiving, warehousing, picking rack stocking, towline, order filling, order sorting, and shipping. Significant techniques were used in each of these areas as well as technical advancements in the state-of-the- art. The most significant points are in 4 of the areas and are discussed in this paper.

Jan 1, 1973

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By T. Dlokweni, A. Z. Toper, A. P. Squelch, R. G. Gürtunca

A collaborative research programme called &apos;DEEPMINE&apos; was established in 1998 to investigate and research the problems of mining below three and five kilometres depths. Backfill is considered as an important support strategy to alleviate rockburst and rockfall problems in current depths and it will even become a more crucial mining strategy at ultra-deep level mining. In this paper, the evaluation and the application of the current backfill design criteria to the ultra-deep level mining environment are studied and a new backfill design criteria is proposed. The new criteria suggests that backfill should still be placed 60 - 70% of the area mined with a maximum fill to face distance of three metres. Furthermore, the vertical stress generated in backfill should be between 2 - 3 MPa at maximum 25 metres from the face at a corresponding strain value of maximum 10%.

Jan 1, 2001

By Charles S. Spirakis

The consistent occurrence of organic carbon early in the paragenesis of Mississippi Valley-type sulfide deposits suggests a genetic link between organic carbon and the sulfide ores. Reduction of sulfate in the mineralizing solution by organic carbon at the sites of mineralization is commonly proposed as the precipitation mechanism for these deposits, but inorganic sulfate reduction is too slow to be important to the chemistry of the ore zone, and bacteria, which catalyze sulfate reduction at low temperatures, are not known to survive at the temperatures of mineralization. Sulfate reduction with or without bacteria is not consistent with the sulfur Isotope evidence. Sulfur isotope studies also indicate that the derivation of sulfur from hydrocarbon at the sites of mineralization is unlikely. Organometallic complexing may be involved in the transport of metals, but no plausible mechanism for breaking these complexes at the sites of mineralization has been proposed. Reduction of partly oxidized sulfur species in the mineralizing solution by organic carbon at the sites of mineralization is a possibility which deserves further scrutiny.

Jan 1, 2013

By Gerald P. Kelton

Over the past quarter of a century, the success of the hydrocyclone as a classifier in closed circuit grinding installations has permitted the introduction of the cyclone into virtually all fields of wet industrial processing. Research and experience gained in these applications have established the optimum cyclone sizes and designs necessary to provide the required performance. Although cyclones are used in widely diverse liquid-solid applications, their use for ultrafine separation clearly demonstrates the importance of a familiarity with previous case studies. Krebs Engineers is firmly dedicated to serving the process industry and has acquired the unsurpassed knowledge and experience to handle all types of separations and classification problems. Cyclones have been used for a number of applications to make what might be considered fine separations. A typical example is in an iron ore grinding circuit where a 381 mm diameter cyclone will classify an overflow product to 85% -44 micron. There is no question that this is a fine separation, but still finer separations are possible, and these are known as ultrafine separations.

Jan 1, 1983