Search Documents

By J. H. Bassarear, P. F. Thomas

Large-scale equipment can reduce both capital and operating costs for concentrators. Large semiautogemus (SAG) mills can be effectively utilized in big mills but they must be kept fully loaded to tab advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semiautogemus mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4476 kW (6000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 t/d (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and jive variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1987

By Erwin A. Morlan

Present methods of boring large hole mine openings are briefly reviewed. Factors that influence the design and choice of down-the-hole equipment for rotary drilling large holes are discussed. With formation drillability taken as a starting point, graphs and charts are given as an aid in the selection of bit load, circulation system, flow rate, drill stem, cutter design and rotary speed.

Jan 1, 1961

By J. Patrick Powers

In tunneling through water-bearing formations, the expense of controlling the water can have a major impact on overall project cost. The author has seen the cost of an eight-foot, finished sewer tunnel rise from under $500 per foot to over $1,000 when a water problem, anticipated as modest, became severe. There is need for greater professionalism in the approach to groundwater control. The days of the forked stick should be behind us. The basic technology exists. Its application is not yet widespread. This paper discusses predrainage; that is, the lowering of water in advance of tunnel excavation. Both free air and compressed air tunnels are considered. Examples from recent tunnel projects are described. SPECIAL NATURE OF TUNNEL DEWATERING Tunneling is unlike other excavations below the water table in a number of significant ways. The tunnel excavation is always on the critical path; if production slows or stops, there is no other work for the heading crews, no other work to carry the cost of service crews and job overhead. The dewatering commitment must be made well in advance. Construction of wells, and pumping down take time. After the heading reaches a trouble area, time is not available

Jan 1, 1997

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997

By Eberhard Stolarski, Michael Tacke

When the oxidized surface gold deposits are mined out, the underlying refractory gold ores become the challenge of treat­ment systems. The size and value ofrefractory gold ore reserves are a function of recovery efficiency and operating cost. The start-up of LURGI's gold roasters at NEWMONT's Carlin site has established whole ore gold roasters as a key to high gold recoveries. The ores from several deposits of the Carlin trend are roast­ed utilizing LURGI / NEWMONT technology, which has achieved gold recoveries approaching 95%. This is in dramatic contrast to the traditional perception that roasting is limited to gold recoveries in the mid 80's. Extensive investigation in pilot scale is required to achieve stable high gold recoveries for most variables in the ore body. The key question for all pilot tests is the classic question of (ROM) run of mine ore roasting or concentrate roasting. All variables are dominated by the leaching/ recovery char­acteristics of the natural ores. The degree ofrecovery improve­ment by roasting / calcining establishes the frame of the eco­nomical conditions. The full range of flexibility is required for the design of the plant to allow for ore variations in heat values, combustible con­tents, agglomeration behavior and off-gas composition. The variables in the ore body influence, therefore, the price of the plant proportionally to its flexibility. Concentrates are usually fairly stable in composition, com­bustion behavior, heat values and particle size since they are a product of the very selective flotation process. Flotation is not the successful process step when the tailings remain high in refractory gold contents.

Jan 1, 1996

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023

By Greg Watson, Dennis Ofiara

"TBMs have been used in mining in decades past, but their use has been limited and sporadic, due to both perceived and actual application difficulties. With new technology and mounting success stories, this is changing. For both coal and metals mining, deep ore bodies require long access tunnels, and an efficient and economical method of reaching those deposits. Today, mining engineers are considering TBMs as part of the overall mine development plan. Planned TBM mine drifts are not only longer, but have more complicated trajectories. Mine development TBMs will have to cope with varying geology, potential for high water inflows, steep gradients, and high temperatures. TBM systems are being planned to cope with such difficulties. TBM systems will be considered and increasingly deployed for mine development, even if commodity prices remain low. TBMs can satisfy the need for increased productivity, better life of mine infrastructure, and safety. Effective conveyor systems are essential to support TBM operation in many mining applications. Many mine development tunnels are slopes, driven down at the steepest practical gradient to reach the deep ore body. Conveyors are often the only safe and effective way to haul the TBM muck form such tunnels. This paper will review the historical use of TBMs in mining, and will discuss the 2015 status of TBMs and conveyor systems in mining, and the special requirements and adaptable features needed in order to make efficient TBMs a reality in mines worldwide.HISTORICAL USE OF TBMS IN MINING APPLICATIONS The first successful hard rock TBM was invented in 1954. Over the next decades, TBMs have been used in many mining applications: Mine access drifts in several Spanish mines •,White Pine Copper Mine, USA •,Selby Coal mine drift, UK •,Coal slopes in Appalachia, USA •,German coal mines accdess drifts, several mines •,Magma Copper San Manuel, USA •,Cape Bretton Undersea Coal Slopes, Canada •,Stillwater Mines, USA"

Jan 1, 2016

By E. A. Lauha

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike sub-district of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike sub-district, there are seven major deposits: Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the sub-district are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Barrick Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post and Deep Star occur both on Barrick and Newmont property.

Jan 1, 1993

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By John K. (Original by) Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1981

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By W. S. Fyfe

Gold is mobilized or made soluble under all crustal conditions given appropriate fluid chemistry with molecules which complex gold. In the surface environment chloride, thiosulphate and a host of organics may mobilize gold. In the epithermal range bisulphide appears effective as shown by the classic studies in the Taupo volcanic zone of New Zealand. In the high grade metamorphic to igneous ranges little is know but it appears that gas molecules in the system CO2 -CO-H20-S-C1 can do the job. Precipitation may occur by changes in P-T-EL-pH or boiling where such changes influence the liquid concentration. Of the known regimes information is good for epithermal systems, poor for surface lateritic environments, inadequate for high-T systems. Gold is often concentrated in bio-systems both living and dead. The influence of biosystems is little appreciated. There is a great potential for the discovery of new types of gold deposits and in particular, gold in weathering environments, gold in very high-T environments, gold in strike-slip faults and thrust regimes, and gold as a by-product in materials like coal and other organic debris. By the year 2500 we may find our noble metal resources in the asteroids.

Jan 1, 1987

By R. M. Smailer

Detailed description of the development of the FIOR process1 and, subsequently, other technical papers relating to the operation and start up of the FIOR plant2,3 are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Company during the 1950's and 1960's; and the facility in Venezuela was designed and constructed by Davy McKee with the plant start up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of the ownership being private capital.

Jan 1, 1981

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today's coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

The 25th Peruvian Mining Convention (Convención de Ingeneieros de-Minas del Perú) was held Sept. 10-14, 2001, in Arequipa, Peru. The biennual meeting, sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru), is designed to showcase the Peruvian mining industry and to ?promote progress in the national mining sector.? The convention consisted of technical sessions, forums, field trips and social activities. The technical sessions featured 80 papers selected from more than 200 papers submitted. The well-organized 2001 meeting was held at the Tecsup Institute of Technology of Arequipa. The meeting was held in conjunction with Exposición Technologica Minera (Extemin), a mining trade exhibition. The2001 Extemin had representatives from more than 400 companies in attendance. In addition to the many Peruvian companies present, the trade exhibition featured pavilions representing the United States, Canada, Germany, Australia and Chile. Registration at the 2001 meeting was about 3,300, a conference record. The theme for the 2001 meeting was Mining: Society and Development. Mario Brescia was chairman of the organizing committee. He said in his opening remarks that ?this year?s meeting seeks to emphasize the commitment on the part of the [mining] companies to treat our natural resources responsibly, controlling any adverse impacts and giving priority to group benefits.? Consistent with this theme, many of the technical papers stressed environmental and social responsibility. Many successful examples of environ-mental and social responsibility on the part of the mining industry were presented in the technical sessions.

Jan 1, 2001

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.