Search Documents

By Weijian Yu, Jianbiao Bai, Jinlin Xin, Shiqiang Xu, Shuai Yan, Zizheng Zhang, Hai Wu

The retained roadway subjected to dynamic loading from thick and hard roof (THF) fracturing caused severe deformations in the thick coal seam (TCS). Understanding the dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF is the first step in determining the stability of the retained roadway. Characteristics of dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF are investigated through numerical simulation and field test of 150208 haulage gate in Sucun coal mine. To improve the reliability of numerical simulation, the double-yield model is used to simulate gob and the strain-softening model is used to simulate filling body; the dynamic module in FLAC3D is used to simulate the dynamic loading due to the THF fracture, and the global model are validated. Characteristics of surrounding rock convergence, plastic zone distribution, and vertical stress in the filling body after the THF fracture are reveled with respect to width to height ratio (W/H) of the filling body and the dynamic loading strength of the THF. The rational width to height ration of the filling body constructed with high-water materials is 0.57. Field monitoring results show that the GER with THF in Sucun coal mine could adapt the dynamic loading due to the THF fracture and meet the requirement. This study is helpful to better study the stability of GER according to the breaking dynamic load of THF and provides reference and guidance for the analysis of breaking dynamic load of THF under similar geological conditions.

Feb 23, 2023

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985

Mineral Resource Technologies(MRT) and Michigan Technological University (MTU)finalized an agreement that permits MRT to offer an advanced carbon removal technology process for coal fly ash from an ash residue generated by utilities. The agreement encompasses the dominant existing US patents using a wet process for fly ash enhancement. The wet process for coal beneficiation of a fly ash product involves four steps. First, a slurry mixture is formed of a fly ash material and a liquid. Second, gravity is used to separate and collect a first-material fraction of the fly ash, having a density less than the liquid. This is done by skimming off the flotation slurry material.

Jan 1, 1996

By J. D. McKay

Continuous column flotation parameter testing, to improve operating methodologies, using coarse bubbles on fluorite ore from Nevada, revealed that retention time is the predominant factor affecting column flotation fluorite recoveries. Column height and feed injection location affected fluorite grades and recoveries because they affected particle retention times in the collection and cleaning zones. Other parameters tested, including froth depth, wash water addition, and axial mixing, showed varying results. Four defined zones within the column were found to have characteristic rates of upgrading per vertical foot. Fluorite-gangue separation was more efficient in a column than in a conventional cell at all particle sizes.

Jan 1, 1987

By Arthur R. MacPherson

Primary autogenous grinding has been in general use for somewhat over 20 years. During this period there have been many highly successful plants built on this principle, while some others have had problems such as: 1. Not performing as predicted from test work. 2. Highly fluctuating tonnage rates. 3. Mechanical problems. 4. High liner wear. Many of the problems with commercial autogenous mills have resulted from improper sampling and testing of the ore during the development period. It is recognized that the fully autogenous mill is very sensitive to any changes in grindability which may occur in the feed to such a mill. The semi-autogenous mill is somewhat less sensitive, but large swings in grindability of the feed require adjustment of ball charge and this cannot be easily accomplished in a short period of time.

Jan 1, 1976

By F. Turatti

Rio Tinto is one of the world's largest mining companies, involved in every stage of metal and mineral production, producing aluminium, copper, diamonds, coal, iron ore, uranium, gold and industrial minerals. Operations are in more than 50 countries in multiple continents and vary in location between large urban centres, regional industrial complexes and remote regions. A risk-based strategy was developed by Rio Tinto to manage its air quality impacts on a global scale. The strategy consists of three objectives ? improving air quality performance, developing industry leading practices and engaging and influencing in air issues. This paper discusses three major successes achieved this approach. Firstly, how air shed resources are managed in constrained air sheds. Secondly, how financial modelling is used to value air quality constraints, and thirdly, how a rigorous and comprehensive e-learning course is used to improve the overall level of air management knowledge of Rio Tinto?s environment managers.

Feb 27, 2013

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By Howard E. Kremers

Although more than 100 thorium-rare earth minerals are known, only a few have any commercial significance. Monazite, thorite, bastnasite, and some exotic thorium rare earth ores are reviewed Commercial interest is presently centered on monazite from the Union of South Africa, and thorite from this country. Thorium became commercially important with the development of the incandescent gas mantle about 75 years ago, Gas mantles consist of thorium oxide with small amounts of cerium oxide. The thorium nitrate used to make gas mantles was first obtained from rare thorium minerals, As a matter of fact, this use of thorium is still important and is one of the largest commercial uses for thorium materials. The discovery of monazite sand placer deposits along the coasts of Travancore, India, and in some Brazilian beach s .s, and the development of the old North and South Carolina monazite stream placers gave the mantle industry of 30 to 40 years ago a comfortable inventory of thorium ore. Even today, the thorium industry depends largely upon monazite ores for its source of thorium. This paper will briefly describe some of the major thorium ores and their principal deposits insofar as they relate to the thorium industry in this country. Because of similar chemical and physical properties, thorium always occurs with the rare earth elements and with varying amounts of yttrium. Thorium may predominate over rare earths, as in thorite-type minerals, or may represent only a fraction of the rare earth content. Typical ratios of thorium to rare earths in various minerals are given in Table 1, The average thorium content of the earth's crust is about 12 grams per ton, and in this respect thorium approximates lead, molybdenum, and some of the rare earths in abundance. The ore minerals of greatest importance to the-thorium-rare earth industry are monazite, thorite-type minerals, bastnasite-type- ores, and the family of minerals which is characterized by a preponderance of the heavy rare earths and yttrium. The latter classification includes xenotime, gadolinite, samarskite, euxenite, etc, The first two, monazite and thorite, are of greatest significance.

Jan 1, 1958

By J. Rao Mokka

Extensive exploration has resulted in delineation of a massive sulfide district on the north flank of the east-central Alaska range. The district covers approximately 400 square miles and contains numerous stratiform; transported and some replacement type sulfide deposits ranging in size from less than 1 million tons to 20 million tons. Five types of ores were sampled for the study. Mineralogical analysis revealed that the minerals are too fine grained for conventional grinding and beneficiation. Hydrometallurgical studies were con-ducted using ferric chloride as a lixiviant. Ore microscopic studies as well as electron microprobe analyses of minerals in the raw samples and leach residues explained the low recoveries for certain elements as well as sources of impurities that need to be eliminated from the process streams.

Jan 1, 1991

By G. W. Phelps

This discussion deals with the geology o£ the Tennessee-Kentucky ball clay deposits; their mineralogy and chemistry; methods of finding, mining and refining; and makes observations on reserves of and future prospects for these clays. Ball clays appear in ceramic formulas for manufacture of vitreous china sanitary-ware, electrical porcelains, floor and wall tile, dinnerware and artwares(l). This type of clay is used for refractory (2) and abrasive products(3), and as a suspending agent for ceramic glazes(4), engobes(5) and porcelain enamel slips(6). Although some ball clay is imported, probably 85-90 percent of ball clay used in the USA(7) is obtained from deposits in Weakley, Henry and Carroll Counties in Tennessee(8), and in adjacent Graves County, Kentucky(9). The term "ball", as applied to clay, probably derives from former mining practice in England whereby conveniently-sized blocks of clay were cut from moist clay beds by spading(10), The expression "ball" has no other technological significance. ASTM(11) defines ball clay as "a secondary clay, commonly characterized by the presence of organic matter, high plasticity, high dry strength, long vitrification range, and a light color when fired." This, and similar(12) definitions, applies to English ball clays but is not satisfactory for many American ball clays. Geology of the Tennessee-Kentucky Ball Clay Deposits Figure 1 shows that most commercial clay areas of the eastern United States lie near the edge of the Coastal Plain; a skew-shaped configuration of its landward boundary outlines the Mississippi Embayment(13), Near the apex of this basin a broad plain, with a rolling, Bullied topography(14), dips gently westward from the Tennessee River to bluffs at the edge of the Mississippi River flood plain.

Jan 1, 1972

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

This study presents the application of low-cost dust monitors (LCDMs) for real-time monitoring of respirable dust in a mining environment. LCDMs significantly enhance data collection by providing continuous, granular and cost-effective dust concentration readings. This case study demonstrates that by deploying LCDMs, mining operators can respond quickly to changes in dust levels, improving occupational safety and air quality management. The results show how such monitoring technologies can be integrated into routine operations to reduce dust exposure and prevent health hazards such as silicosis, especially when coupled with appropriate mitigation strategies.

Nov 1, 2024

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By M. J. Richards

Spontaneous combustion caused by the movement of air through the waste is a major problem. Combat methods attempt to exclude oxygen rich air, but little is known about airflow through the waste. The use of a tracer gas technique to monitor the flow of nitrogen from an injection hole during inertisation is described. Correlations are drawn between barometric pressure changes and the nitrogen entering the waste. As no information was obtained about airflow and oxidation zones, a second experiment was conducted to sample from the waste, but the results were inconclusive. A finite element method developed to model the pressure and airflow distribution, under steady state and nitrogen injection conditions is outlined

Jan 1, 1987

By J. Tavares

It is no mystery why the mining industry has such lofty safety standards. In dealing with Mother Nature and gravity, the combination of the two can create significant hazards from high wall and tunnel collapses to huge landslides. The loss of production from a major disruption could be enormous. The price tag on the loss of human life is immeasurable. The evolution of geotechnical instruments and software has been ongoing for years. But the biggest innovations have occurred during the era of cell modems, internet, and wireless networks, allowing for real time data and alarms to be delivered globally anywhere and anytime to one?s computer, laptop and smartphone. Yet in some ways you can thank the urban construction projects for developing much of the technology in use by today?s mines. Due to the density of population and the billions in dollars of structures and infrastructure in cities throughout the US and the world, urban projects have faced intense scrutiny for years. Out of this scrutiny was born the necessity of real time automated monitoring of instrumentation and sensors, a defence against catastrophic failures, and real time early warning systems through alarms that can and do saves lives. It is also possible to identify areas of concern with subsequent remediation prior to failure.

Feb 23, 2014

By L. Cheng

Almost all modern cutting bits use a cemented tungsten carbide tip to provide adequate hit life against wear. Laboratory tests by the US Bureau of Mines have indicated that the number of strikes for ignition increased by a factor of three with a new non-rotating bit impacting a sandstone block when the clearance angle was increased by 10°, and that carbide-tipped bits allowed more strikes before ignition than steel-tipped bits by a factor of 7 to 10. Recent field tests in an operating coal mine indicate a dramatic reduction in the frequency of frictional ignitions and improvement in hit life by using a mushroom-shaped hit cap and a larger initial clearance angle. The latter was achieved by increasing the hit attack angle. Improved hit performance through selection of the grade of tungsten-carbide is a com¬promise between fracture resistance and wear resistance. A large clearance angle should he maintained by various techniques, such as a variable attack angle holder, or a reusable hit that can he reground.

Jan 1, 1990

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By Charles K. Presley

This paper deals with drilling large diameter shafts for the mining and construction industry with diameters in excess of 3 feet to more than 20 feet in diameter. It discusses appropriate applications of the rotary drill method, linings for large diameter shafts, circulation systems,, and the limitations of the method. Each specific rotary drill method is determined by the geology of the area, the depth to be drilled and the formation fluids encountered. Shaft lining or casing must be improved to result in lighter weight, higher strength and lower cost. All phases of rotary drilling equipment must be improved to drill shafts in excess of 10 feet in diameter. As these goals are reached, more shafts of large diameter will be drilled by the rotary method for the mining and construction industry.

Jan 1, 1967