Search Documents

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Aydin Shaterpour Mamaghani, Bilgin. Nuh, Engin Dogan, Tayfun Erdogan

"Improved safety and more environmentally friendly operation are basic advantages of mechanical excavation over the drill and blast method. Raise Boring Machines (RBMs) are one of the types of these machines which have recently been increased use in Turkey. The excavated hole with RBM is more stable than other methods and has better air flow, making it ideal for ventilation shafts. This paper is a summary of the performance of a RBM in the Balya PB-Zn Mine in Turkey. Length and diameter of the ventilation shaft are 200 m and 2.4 m, respectively. The geological and geotechnical characteristics of the strata excavated in the mine are first given and later the validity of a model developed to predict the machine performance is discussed. It is believed that the results of this study and the model given to estimate the performance of the RBM will be useful guide for future applications. INTRODUCTION Raise boring technology was developed to meet the demands of the mining industry, but has also found numerous applications in tunneling or infrastructure projects for ventilation purposes. Raise boring machine uses a small diameter drill rod, around 230-350 mm to drill a pilot hole down to the required depth up to around 2000 m. Once the pilot hole has been drilled to the desired depth, a reamer of up to 9 m diameter is attached to the drill rod. The reamer is then pulled back up to the upper level, creating a round shape. Continues operation provides a faster advance rate than other methods. RBMs are suitable both in hard and soft rock. The flexibility in different angles and diameters is a great advantage compared to drill and blast excavation method. RBM creates a shaft with smooth walls which usually does not require lining. The hole is more stable than a drilled and blasted method and has better air flow, making it ideal for ventilation shafts. Raise boring is convenient method in competent rock; however several problems are faced in geological formations where geological discontinuities are dominant. Moreover, assembly and disassembly time may be long in some cases. The performance and operational parameters of the excavating machine should be predicted prior to starting the excavation operations in order to fulfill the economic requirements of the project. In the light of this fact, the main objective of this investigation is to summarize a case study on raise boring machine performance and suggest a new model based on laboratory test results. First, general description of the mine and project are provided. Then, the physical and mechanical characteristics of the samples taken from project area are discussed. In the third section, performance and operational parameters of RBM are investigated to understand the machine behavior in different rock characteristics and also to collect a useful database for further investigation. In the fourth section, a new model for performance estimation of RBM are recommended."

Jan 1, 2016

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By S. K. Mishra, S. B. Kanungo, D. Biswal

An attempt was made to beneficiate low-grade, high-phosphorus manganese ores of the Garividi-Garbham region of Andhra Pradesh, India, by using wet high-intensity magnetic separation (WHIMS). The distribution behavior of both mass and chemical constituents in different size fractions of a typical highly weathered ore sample was studied to obtain information about the liberation characteristics of various chemical constituents. Magnetic separation indicated that in the +208-µm size fractions, P and acid insolubles were concentrated in the magnetic fractions. However, in the -208-µm size fractions, P and acid insolubles were concentrated in the nonmagnetic fraction because of a lower recovery of the magnetic fraction. Variations in field intensity between 1.3 and 1.75 T had little effect on the recovery and the grade of concentrate. The results also demonstrated that phosphorus was associated with all three major constituent phases, namely, oxides of Mn and Fe and aluminosilicate gangue minerals.

Jan 1, 2000

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By Kermit Allen

Storing natural gas in solution mined salt cavities appears to be one of the more promising methods being considered by some major gas transmission companies for meeting peak demands. Historically, these companies have been faced with the problem of meeting peak demands when the source of natural gas is located hundreds of miles from the marketing area. Transcontinental Gas Pipe Line Corporation's position was further complicated because some of its offshore Gulf Coast gas supply wells may have to be shut in during hurricane alerts. Transco's solution was to construct. solution mined salt storage caverns adjacent to its pipeline near Eminence, Mississippi. (See Figure 1.) In 1965, Fenix & Scisson, Inc., was engaged by Transco to evaluate the feasibility of storing natural gas in caverns dissolved from salt at selected locations along Transco's pipeline to the East Coast. In June of that year a report was submitted to Transco concluding that this proposal was feasible and recommending several potential sites for storage development. Additional engineering and geological studies followed and in March 1968 the Eminence Salt Dome site was selected and storage construction began that year.

Jan 1, 1971

By M. Sinirkaya

The dissolution process of phosphate rock from the Semikan area (Mardin-Mazidagi, Turkey) using dilute phosphoric acid has been investigated. The work involved studying the effect of important variables, such as reaction time, stirring speed, particle size fraction, phosphoric acid concentration and temperature. Van der Sluis et al.?s model was used to determine the rate of the partial dissolution of phosphate ore. Mass-transfer coefficients (kL) varied between 2.8 and 28.5.10-3 m.s-1. The activation energy of the process varied between 16 and 20 kJ.mol-1. It has been found that the dissolution process is controlled by calcium ion diffusion, rather than by chemical reaction.

Jan 1, 2010

By Monserrat Rebolledo, John L. Uhrie, Candice Simms

Jetti Resources has developed a catalyst which overcomes the passivation of primary sulfides, enhancing the heap leach recovery of copper from chalcopyrite. It is important to emphasize that heap leaching of copper sulfides, whether with or without the Jetti catalyst, is a biooxidative process. We have demonstrated the efficacy of Jetti’s technology in bioreactors, with a chalcopyrite-dominant porphyry ore. In the presence of Jetti’s technology, optimal bioleaching conditions significantly increase copper extraction by 2.6 times that of the baseline.

Feb 1, 2025

By L. John Minnick

A revised and expanded edition of a previous paper** dealing with reactions of calcium and magnesium oxides and hydroxides with pulverized coal fly ash is presented. Lime-fly ash specimens were cured at constant temperature and subjected to X-ray diffractometry, differential thermal analysis, pozzolanic reactivity tests, and microscopical investigations. Bars of limefly ash were subjected to cycles of wetting and drying, and measurements of length change were recorded. A discussion of variations within and among types of lime and types of fly ash is presented. The nature of the pozzolanic reaction is reviewed, particularly as related to compounds which are used up and formed during the aging process. The relationship between the pozzolanic reaction and the resultant physical properties of the mixtures is examined.

Jan 1, 1968

By J. H. Gwynne

[ ]

Jan 1, 1962

When the Middle Ages were drawing to an end and Rotterdam, then still a small fishing port, began to extend its trade relations to continental ports handling general cargo, a development was initiated which was to give Rotterdam a predominant position in maritime traffic in Europe 300 years later. Despite many setbacks and the silting up of the mouths of the Rhine and Meuse rivers, the port experienced a new rise towards the end of the previous century after the dunes at Hook of Holland had been cut through as planned by Dutch engineer Caland. With its favourable location in the mouth area of the Rhine and a hinterland opened up by waterways it was merely a matter of the city council pursuing a far-sighted policy to make the best of these natural advantages. Thus new port installations were erected on the southern bank of the Meuse in the first quarter of this century, which were expanded in the course of the subsequent decades. The New Waterway became the main artery for industrial enterprises, in particular oil industries, which sprang up along its banks (picture 1). Whereas 30 years ago Rotterdam's Waalhaven, with its new jettees for general cargo and mainly bulk goods, was still one of the most modern terminals, the growing size of ships, which increased by leaps and bounds for tankers, in particular towards the end of the 'fifties, necessitated much larger harbour facilities built further and further towards deep water.

Jan 1, 1972

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By Terence P. McNulty

Gold-bearing outcrops were discovered in 1862 by Union soldiers garrisoned at Needles, CA, near the northwest corner of the future State of Arizona. Sporadic mining began several years later, but engineered shaft sinking and mill construction were not adopted at Oatman and the neighboring camp of Goldroad until about 1900. Geological interpretations in 1915 enabled major production during the next decade. In the late-1930s, USSR&M built a new mine and mill in Gold Road and the District flourished until closure by Federal Order L-208 in October 1942. For about a decade, Oatman’s mines were among the largest gold producers in the American West.

Feb 1, 2024

By Charles H. Wells

This paper describes a commercial installation of a sophisticated instrumentation and control system designed to maximize the performance of heavy medium cyclones. Samples of plant feed and its products were collected and analyzed for ash content so that measures of efficiency could be determined for plant operation under (1) manual control and (2) automatic (computer) control. The heavy medium cyclone control strategy and its digital computer implementation are discussed in detail. The sample results are analyzed and the economic benefits of automatic control are discussed. Results from the initial data sets quantify the economic benefits of automatic closed-loop control; viz, increased recovery and reduced clean coal variability have been clearly demonstrated.

Jan 1, 1981

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By Earl M. Frizzell

Investigation of mined land characteristics, evaluation of irrigation systems and evaluations by the mining industry determined that irrigation is a feasible method for aiding the revegetation of coal mined lands in the western arid and semi-arid regions (Sherman, et al. 1980). The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid-set irrigation. Irrigation should be supplemental by complimenting natural precipitation and should be implemented on a temporary basis. For germination, the vegetation requires application of small amounts of water in a gentle, frequent, and timely manner. For the establishment phase of growth, moisture should be applied and stored in the soil either through pre-irrigation or deep irrigation.

Jan 1, 1985

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Mark A. Krall

The Conda Partnership's Dry Valley Phosphate mine is a thinly bedded, multiple seam, open pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/ dozer operations. The ore that is mined is shipped 32 km (20 miles) by rail to a beneficiation facility which upgrades the ore via washing and calcining. The mine and beneficiation complexes are owned by the Conda Partnership. The Conda Partnership is a joint venture between Beker Industries Corp. of Greenwich, Connecticut, and Western Co-Operative Fertilizers (U.S.) Inc. of Alberta, Canada. The Conda Partnership operates as a separate entity from the two partners.

Jan 1, 1984

By C. E. Semler

A 5 year test program, involving on-line, in-vessel exposures at Barrick Goldstrike Mines. Inc. has provided valuable information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products have been evaluated. Properties before and after exposure are used to document the performance. Benefits have included the development of a new silicate mortar improved understanding of brick requirements and increased autoclave operating time between maintenance shut-downs. More improvements are expected in the future based on further information from the test program.

Jan 1, 1997

By Jan Visman, James W. Parkinson

GENERAL INTRODUCTION Sample collection, preparation and analysis are all steps in a single process designed to provide information about a much larger amount of material than the sample itself. For example, information about the ash content of a unit train load of coal may be derived from a single, relatively small sample of perhaps a few hundred pounds (liters) extracted from the entire shipment. These three steps can be thought of as links in a chain, allowing the simple analogy that the strength of the chain, or, in other words, the value of the information is only as strong as the weakest link. Sample collection, discussed in Part 1 of this chapter, is critical because analytical procedures can do no more than reveal the characteristics of the sample presented to the laboratory. If that sample does not properly represent the population to be characterized, neither will the analysis of that sample. Sample preparation is also a critical part of the chain. Any change in the nature of a sample between the time it is collected and the time it is analyzed will appear to reflect the nature of the population. For example, sample preparation procedures that allow air to partially dry the coal sample before reaching the laboratory will cause the sample analysis to indicate a lower moisture content than the sample originally had. Other changes can be more subtle. Second only to moisture loss, oxidation reactions generally cause the greatest problems. Oxidation of a coal sample can alter surface properties, changing flotation response. In extreme cases, combustion parameters, such as caking or agglomerating properties or mineral composition, such as pyrite content, can change. Water samples can also be altered by oxidation. For example, ferrous iron can oxidize to ferric iron, possibly changing water quality parameters such as pH. Sample analysis, the subject of Part 2 of this chapter, is the final link in the chain. Obviously, no laboratory procedure can correct for problems created by improper sample collection and preparation. At the same time, poor analytical techniques will create incorrect information about the total amount of coal from which the sample was extracted (the population) in the same manner as improper sample collection and preparation. The key to gaining correct information about the population is to view these three steps as parts of a single process. Following proper techniques through only one or two steps of the process will not produce accurate information.

Jan 1, 1991