Search Documents

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By G. K. Derby

Paper presents project results investigating current techniques for dragline wire rope removal and the development of less hazardous means of performing the task. The cannon is the most prevalent method used in American surface mines. A cannon test program was conducted that used 40-and 50-grain primer cord to establish force produced using a 56-pound projectile. Socketlwedges were separated to establish separation force data. Two alternative removal methods, pendulum ram and portable hydraulic pusher, were developed and tested. Both provide sufficient force to effect separations under normal conditions on draglines with up to 78- cubic yard buckets.

Jan 1, 1984

By Richard A. Thomas, Connor B. Brown, Thomas H. Dubaniewicz, Teresa Barone

Electric vehicles powered by lithium-ion (Li-ion) batteries are being developed by mining vehicle manufacturers as a replacement for diesel-powered vehicles. Explosion-proof (XP) enclosures are frequently employed to enclose electrical ignition sources in gaseous underground mines to prevent the spread of an internal methane-air explosion to a nearby explosive atmosphere. Due to thermal runaway (TR), Li-ion batteries have the potential to cause pressurized explosions in an enclosed structure. Past research has shown the potential for well-confined Li-ion cell TR to drive pressures beyond the conventional pressure specification for XP enclosures. Researchers at the National Institute for Occupational Safety and Health (NIOSH) used an Accelerating Rate Calorimeter (ARC) to induce thermal runaway of Lithium Titanate or Lithium Titanium Oxide (LTO) type 18650 cells enclosed within containers with various volumes and found an inverse power relationship between the TR pressure and available free space. The results were similar in magnitude to that of lithium iron phosphate (LFP) cells, which were used in prior testing. Temperatures, gas amounts, and TR pressure-rise rates were also recorded. The data indicate that with enough free space, the pressures can be lowered below the conventional pressure specification for XP enclosures.

Feb 1, 2024

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014

By G. T. Adel, P. E. Richardson, R. Pazhianur

Cathodic protection using impressed current was employed to reduce mill wall wear during ball milling. Wear rates were determined from weight-loss measurements made on four 1-in.-diam mild steel coupons that were installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH levels of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 30% to 60%. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It was also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1998

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By P. L. De Bruyn

[According to the Young equation, SG = SL + Coso, the equilibrium contact angle depends on the values of the three interfacial tensions involved. A solute promotes wetting, i. e. a decrease of contact angle if it decreases.LG and/or YSL or if it increases SG. Dewetting, the important step in flotation is, promoted if the solute increases y and/or SL or decreases. Most solutes used for wetting or dewetting are, positively adsorbed at all interfaces involved and consequently according to the Gibbs equation lower the interfacial tensions. Wetting is therefore expected to occur if LG and SL are more affected by the solute than SG. Dewetting on the other, hand demands a greater decrease of SG than that of SL (and of LG). See P. L. de Bruyn, J. Th. G. Overbeek and B. Schuhmann, Jr., Mining Engineering (1954) P. 519.]

Jan 1, 1960

By L. Schlink

Impacted waters, often complex, are created in mining which at some point in the mine life cycle will need to be attended. The simplest and most cost effective method of handling impacted water is to reuse it as makeup water for operations. At the end of mine life, operational reuse will not be an option and the impacted water will require treatment to achieve alternative reuse goals. Conventional mine impacted water treatment is successful in removing unwanted constituents but create brine and sludge that may require special handling or additional treatment, resulting in additional liabilities and costs. Freeport-McMoRan Copper & Gold has taken an approach to water treatment that focuses on transformation not concentration. The Water Treatment Test Facility located at Sierrita Mine has three test plants that are piloting the mine impacted water transformation process. Two plants have been designed for the removal of calcium and sulfate with products of gypsum and sulfur. The third plant removes metals from process water and transforms them into marketable metal sulfides. The transformation, rather than concentration, of mine impacted water solutes greatly reduce long term risks.

Feb 23, 2014

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

With the depletion of mineral resources and the growing demand for metal resources from industrial development, the recovery of metal resources from secondary resources has attracted increased attention. Among all secondary resources, spent catalyst is one of the most important as it contains valuable metals such as vanadium, nickel, molybdenum, cobalt, and aluminum. Compared with the extraction of metals from minerals, the recovery of valuable metals from spent catalysts has the advantages of a simple process, a short production cycle, lower investment cost, and less environmental impact.

Apr 1, 2023

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By Linda D. Raedeke

The main platinum-group metal (PGM) deposit in the Stillwater Complex is associated with a stratiform zone formed by magma mixing. In general, the intrusion is a large, layered body of Archean age which formed by repeated magmatic injections in- to a single, large, hypabyssal magma chamber. The Complex is broadly divided into the lower Ultramafic series of olivine ± orthopyroxene rocks (1000-2000 m thick) and the upper Banded series of predominantly plagioclase-rich rocks (24500 m thick). The latter is further divided into Lower, Middle, and Up- per Banded zones. The Ultramafic series, plus most of the Lower and Upper Banded zones formed from repeated injections of an olivine-saturated magma, the rocks accumulating from the floor upward with a crystallization order of olivine, or- thopyroxene, plagioclase, clinopyroxene. The olivine-bearing subzones of the Middle Banded zone formed predominantly from a magma which crystallized in the sequence plagioclase, olivine, clinopyroxene. Olivine-bearing subzone I, with which the PGM mineralization is associated, occurs generally -400 m above the Ultramafic series-Banded series contact. Ore grade mineralization is usually found in plagioclase or plagioclase-olivine cumulates. The platinum-group elements are associated with disseminated base-metal sulfides dominated by the assemblage, pyrrhotite-chalcopyrite-pentlandite. Olivine-bearing subzone I marks an interruption in the crystallization sequence of the Lower Banded zone, with the reappearance of cumulus olivine and an associated change of the crystallization sequence. These changes indicate the addition and mixing of a secondary magma of the same composition as that which later dominated in the formation of the Middle Banded zone. Characteristics associated with mixing include laterally discontinuous but well-developed layers, xenoliths of ultramafic rocks, and sedimentary-type structures such as slum- ping and graded layering. The influx of new magma caused sulfide saturation by one or more of several chemical changes including addition of sulfur, decrease in oxygen fugacity, decrease in FeO, or increase in SiO2. Once an immiscible sulfide liquid was formed, platinum-group elements were scavenged from the magma by the sulfide liquid and segregated.

Jan 1, 2013

By J. A. Hartlage

Four years ago, Ashland Chemical Company introduced a new copper solvent extraction reagent for hydrometallurgical utilization. The reagent, an alkylated 8-hydroxyquinoline, is called Kelex 100 ®(1). Since the time of introduction, the reagent has been investigated by several workers for its solvent extraction utility in the separation and purification of transition metals (2-7). In the following text, those factors which are essential to the optimum performance of Kelex 100 on concentrated copper solutions will be discussed. To date, the reagent has been found useful in active concentrations of from 1 to 20% Kelex 100. In order to achieve the best performance for Kelex 100, it has been found that a phase modifier is essential. Various alcohols and phenols have been evaluated in order to improve phase performance and stripping characteristics of the solvent system. Modifiers and diluents are especially important when solvent activities between 3 and 20% Kelex 100 are employed. A 15% Kelex 100 solvent, for example, containing 15% nonyl phenol in Escaid 100 (Exxon) can be utilized to remove greater than 33 grams per liter of copper from an aqueous feed without interstage neutralization, and in the same process scheme the reagent can be stripped to less than 1 gram per liter barren organic producing a pregnant electrolyte containing greater than 40 grams per liter copper and less than 120 grams per liter sulphuric acid. The unusually efficient stripping of Kelex is accomplished by protenation of the extractive molecule during the stripping process.

Jan 1, 1974