Search Documents

By Erwin Riyanto, Roy William, Karl Llewellyn

The Deep Mill Level Zone (DMLZ) mine is currently one of the deepest block cave mines in the world. The rock mass is heavily veined with little to no joints and faults are usually healed cohesive structures leading to difficult cave mining conditions. The caving process is improved if the rock mass contains fractures with sufficient density that it will cave by gravity as undercutting progresses. Hydraulic fracturing (HF) has been used to create fractures around the cave to improve mining. A seismic monitoring system has been used in DMLZ since the start of mining. Therefore, the seismic activities before, during and after HF can be monitored. Shear wave splitting is a process used to study the impacts of HF on the rock mass. This process involves the measurement of travel times from splitting shear waves after seismic events and using this to define the anisotropy within the rock mass and subsequently fracture density. This paper sets out the methodology for carrying out the interpretation of the shear wave splitting process using seismic data from the fracked cave crown and abutments along with an overview of the benefits to cave mining as result.

Apr 26, 2022

By ANA E. BOHE, MICCO GEORGINA DE, GASTON G. FOUGA, JUAN P. GAVIRIA, FEDERICO J. POMIRO

To the best of our knowledge, this paper comprehensively summarizes a thorough study to determine the thermodynamic viability of the reactions between light rare earth oxides and chlorine with and without carbon. The kinetics and mechanisms of light rare earth oxide chlorination and carbochlorination reactions are analyzed and discussed according to results in the literature. Lanthanides between lanthanum (La) and gadolinium (Gd) are considered as light rare earth elements (LREEs) in agreement with previous literature and the results detailed in this review. Both laboratory- and industrial-scale light rare earth chlorinations and carbochlorinations, starting from oxides and ores, are reviewed.

By Y. Lahaye, O. Martinsson, B. I. Palsson

"Four main and three minor rare-earth-element (REE)-bearing minerals were identified and quantified in the Kiirunavaara apatite iron ore tailings using optical microscopy, an electron probe microanalyzer (EPMA) and a mineral liberation analyzer, and their chemical compositions were analyzed by the EPMA and laser ablation inductively coupled plasmamass spectrometry. REEs are shown to be contained in the minerals apatite, monazite, allanite, titanite, zircon, thorite and synchysite. In zircon, thorite and synchysite, they occurred in only trace amounts and contributed limited amounts to the total REE budget, and these are consequently of minor importance. Monazite occurred as inclusions in apatite and as free particles, 90 percent liberated. Allanite occurred to some degree in mixed grains with magnetite but also as free particles. Monazite mainly reported to the apatite concentrate, while allanite and titanite largely went to the tailings, the latter preferably to those fractions smaller than 38 µm. The amount of titanite in the finest tailings fraction was 2.3 weight percent, containing close to 1 percent REEs, with heavy rare earth elements (HREEs) making up 28 percent of the total REEs. However, a texturally distinct group of titanite grains showed an HREE/REE ratio of up to 67 percent. Furthermore, titanum dioxide analyses indicate that titanite is preferentially released into the tailings from the secondary magnetic separation step in the concentrator. Our data therefore suggest that titanite, occasionally enriched in HREEs, can be extracted from the processing stream and might thus be considered a new source for REEs at Kiirunavaara and similar deposits.IntroductionDeposits of apatite iron ores are the major source for iron in the European Union and are exploited by Luossavaara-Kiirunavaara AB (LKAB) in several mines in the Kiruna-Malmberget area in northern Sweden. Kiirunavaara is the largest of the apatite iron orebodies in Sweden, comprising more than 2 Gt of iron ore with 60 to 68 percent iron (Fe). At the end of 2015, the total accumulated production of crude ore from openpit and underground mining since the start of mining was 1,566 Mt, with ore reserves of 644 Mt grading 46.3 percent Fe (LKAB, 2016). The deposit defines a steeply dipping tabular body, approximately 6 km long and up to 180 m thick, extending at least 1,500 m below the surface. It is situated in the middle part of the Palaeoproterozoic Kiirunavaara Group of volcanic rocks and follows the contact between a thick pile of trachyandesitic lava and overlying pyroclastics (Martinsson, 2004)."

Jan 1, 2017

By F. A. Edwards

The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounces per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m elevation (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required a three lift hoisting system for men, materials and ore. In addition to the increased travel time and ore handling expense, increased humidity, temperature, ventilation and compressed air losses have added to the inefficiency of the operation. As a result, studies were initiated in 1980 to assess the future of the Macassa operation. The results of the studies indicated that a new deep shaft with a potential to hoist from 2,135 m (7,000 feet) or below was the most attractive option. Detailed design of the shaft and associated surface plant commenced in January, 1982 and the following milestone dates were achieved: 1980 - initial study of hoisting and haulage facilities; January, 1981 - ore reserves in excess of 1 million tonnes of ore at 18.7 g/tonne (0.45 oz/ton) confirmed; March, 1982 - preliminary study of Macassa No. 3 Shaft completed; April, 1982 - permanent hoisting plant purchased; June, 1982 - site clearing commenced; September, 1982 - shaft collared; May 1, 1983 - shaft sinking commenced; February 11, 1985 - shaft reached 1,600 m (1mile); December 1, 1985 - shaft scheduled for completion.

Jan 1, 1985

By A. Bieg, M. Samson, Z. Bell, A. Zinsser, J. Schuyler

As the world progresses toward the renewable energy transition, the demand for minerals increases exponentially. According to the International Energy Agency (IEA) 2021 Net Zero by 2050 Report, critical mineral production needs to grow six times to combat climate change. It’s estimated that four to seven percent of global greenhouse gas (GHG) emissions come from the mining sector’s Scope 1 and 2 (direct and indirect) emissions. Including Scope 3 (upstream, downstream, and embedded) emissions, the sector accounts for 28% of global GHG emissions. In a typical mining operation, diesel fuel is the biggest source of direct GHG emissions, and haulage is often the main source of diesel emissions. Large haul trucks have been the industry standard for over 50 years and offer flexibility, relatively low capital cost (especially with equipment lease options), and guaranteed technology with known maintenance. The challenge will be to justify their continued use when there are more economical options that lead to significant reductions in GHG emissions. The purpose of this study is to compare five haulage options in terms of GHG emissions, using the methodology defined by the Greenhouse Gas Protocol Scopes 1, 2, and 3 (Category 2). Additionally, this analysis compares operating and capital costs associated with the five haulage options (emerging and proven technologies): 1) Diesel-Electric Haul Trucks, 2) Battery-Electric Haul Trucks, 3) Fuel Cell Haul Trucks, 4) Railveyor, and 5) Conveyor. This analysis looks at the emissions and costs associated with operating the equipment (fuel and electricity), the embedded emissions and costs associated with the construction and installation of the equipment itself, and the associated infrastructure (roads, powerlines, and rail).

Feb 1, 2023

By A. J. S. Spearing, T. Kostecki, D. Benton

The use of paste backfill in room-and-pillar coal mines in the United States needs to be fully investigated. This paper discusses a series of physical tests that were conducted to examine the support benefits of theoretical paste backfill regimens in Illinois Basin room-and-pillar coal mines, which necessarily included consideration of weak floor conditions. The series of tests included those simulating strong floor conditions, weak floor conditions, under-confined scenarios, and testing of actual coal-based paste backfill samples. The testing indicated that a paste backfill regimen utilizing a minimum backfill strength of 22 psi at a minimum fill height of 50% of pillar height could significantly increase the longterm stability of coal pillars in the Illinois Basin. Considering typical coal wash plant recoveries, 50% fill would be feasible.

Jan 1, 2014

By Brianna Eiter, Max Barham, Tim Bauerle

While not well established, there is evidence that the mining industry is encumbered by several work-related fatigue risk factors. Compared to other industries, mine workers are more likely to report inadequate sleep and work longer hours per day. Given these observations, there is a critical need to identify effective ways to intervene, manage, and mitigate mine worker fatigue and sleepiness when present. One barrier to this is confusion around the similarities and differences between fatigue and sleepiness, which can result in these terms being treated as interchangeable regardless of context and make it difficult to assess and mitigate safety risk.

May 1, 2024

By M. Rieber

The recent history of the mercury market results almost entirely from U.S. Government actions. Its derived demand has been curtailed by U.S.E.P.A. mandates; its supply has been augmented by U.S.D.L.A. controlled stockpile releases. The resultant prices have altered its market structure, impacted mercury mining, refiners and recyclers, and affected international production and markets. From a marketplace product mercury is rapidly becoming a disposal problem. Other minerals may follow in its wake. This paper reviews developments in demand, particularly in relation to environmental constraints. Supply side impacts are considered. The impact of stockpiles, both as a market overhang and as a potential supply is reviewed. Government stockpile disposal activity is emphasized, but the size, estimated disposal rate, and quality of the private stockpiles are considered, as is the potential availability of additional material from shut-in mines.

Jan 1, 1995

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By James R. Jones

It has been 2-1/2 years since the Congress passed the Surface Mining Control and Reclamation Act of 1977 (PL95-87) the Office of Surface Mining every deadline specified in the Act. Hopefully the Congress will begin to realize that specifying unrealistic deadlines does not accomplish the end desire of legislation any sooner -- it only adds to the confusion, and actually hinders orderly, efficient progress. OSM has been sued by all categories of involved parties -- environmental activitist organizations, the states, and the coal operators. This situation has resulted for two reasons: (1) insufficient time was allotted by the Congress to properly develop the regulations and program, and (2) OSM?s philosophy that it must dictate every detail of reclamation operations from Washington, even though many of its people are inexperienced with coal mining. These law- suits are now demonstrating their value. OSM is showing signs of "pulling-in-its horns" and, hopefully, will approach the revised regulations in a more realistic fasion.

Jan 1, 1980

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By Felicia F. Peng

Using granular media for removal of soluble manganese from mine water and industry waste stream has the advantage of forming a compact surface layer of manganese oxide coating on the media. This process can avoid the step involving the separation of voluminous sludge of manganese hydroxide by the high-pH method for soluble manganese removal. The removal of soluble manganese is accomplished by adsorption and oxidation. The adsorption of Mn(II) on the manganese oxide-coated media was rapid through the specific adsorption and may be due to the ion exchange of hydroxyl ions on the manganese oxide by Mn(II). In the subsequent step, the adsorbed Mn(II) form the intermediate manganese complex on the manganese oxide product is oxidized with dissolved oxygen or other available oxidant source in the aqueous solution. This paper presents the efficiency of removal of soluble manganese from mine water by using a laboratory fluidized bed and the recovery of manganese oxide coating on the anthracite coal particles. In order to accelerate the formation of the manganese oxide layer on the surface of anthracite media, dilute potassium permanganate solution is used as an active oxidant. The effects of operation parameters on the manganese removal including pH, flow rate, concentration of feed and oxidant dosage are evaluated.

Jan 1, 1996

By Courtney Chamberlain

The Telfer Project, Australia's newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By Raja V. Ramani

Worldwide, promulgation and enforcement of health and safety laws and regulations have been the primary means of ensuring minimum and uniform standards of health and safety in the mining industry. In U.S. coal mines, a new era was ushered-in in 1969 for the control of health hazards from respirable coal mine dust. Since then significant progress has been made on all aspects of the respirable dust problem-its definition, monitoring, reduction, and control. In the intervening years, our ability to monitor, analyze, and characterize the mine atmospheric environment and the health of miners has increased many fold. Also, advancements in production technology have far outdistanced enhancements in environmental control technology. Therefore, questions are continuing to be raised on the adequacy of the characterization and control measures with regard to both the airborne respirable dust in mines and the health effects of respirable dust. Late in 1995, the Secretary of Labor appointed an Advisory Committee on the Elimination of Pneumoconiosis Amona Coal " Mine Workers (Dust Advisory Committee) to review the progress towards elimination of coal worker's pneumoconiosis (CWP) and silicosis, and in the program to control respirable coal mine dust in underground and surface mines, and make recommendations including improved standards and other appropriate measures for the control of exposure to airborne coal mine dust. The Committee's report was released in October, 1996. In this paper, a summary of the recommendations of the Committee is presented. A brief discussion of the background, and the issues and findings leading to the recommendations is also presented. The Committee concluded that the progress made towards making mines safer from the health hazards of respirable coal mine dust is substantial but that it is not sufficient to achieve the intent of the 1969 Coal Act. The Committee's recommendations encompass a wide range of issues addressing permissible exposure limits (PELS), sampling, dust control plans, hazard and medical surveillances, role of miners, training, and research and development.

Jan 1, 1997

By W. A. Crosby

All mine operators using explosives want to maximize explosive performance while minimizing blasting costs. Use of bulk explosive products such as AN/FO, heavy AN/FO, slurries and emulsions has greatly improved blasting efficiency over the years. Many operators have improved energy output from these products by adding aluminum. A major problem facing them is the fluctuation in aluminum price. The question therefore becomes, when is it economically advantageous to use aluminum in bulk products? This paper answers this question by first reviewing the energy output from the main types of aluminized and non aluminized bulk mixed explosives and then by showing the relationship between the different products on a cost and energy basis. The paper finally presents examples of charts and tables which will aid mine operators to conveniently select the most economically correct bulk explosive, including the level of aluminum addition.

Jan 1, 1991