Search Documents

By R. Gorakhki, R. Stafford, A. Jung

Geosynthetic clay liners (GCLs) have been used widely as an alternative for compacted clay liners and covers in mine waste applications. The high swelling of bentonite particles in the GCL creates a uniform barrier layer that results in low permeability of water and mine waste leachate. GCLs must provide sufficient internal and interface shear strength stability, especially if GCLs are used in steep slopes under high normal loads. Peel strength is a common parameter that is typically correlated to internal shear strength properties of GCLs. The relationship between internal shear strength and peel strength of GCL at normal stresses of 287, 575, 862, and 1724 kPa is evaluated in this study. The data in this study was compared with the peel strength-internal shear strength relationships found in literature. The study concludes that the relationship between peel strength and internal shear strength is unique based on manufacturing, needle-punching density and the method with and without heat treatment of the geotextile end fiber bundles.

Feb 1, 2023

By R. J. Hickson

The giant El Abra copper mine project under development in Northern Chile will come on stream in early 1997 at a production rate of 500 million pounds of cathode copper annually. Ownership is 51 % Cyprus Amax and 49% Codelco. Cyprus Amax has construction responsibility. Total project cost is $1050 million. El Abra will incorporate latest operational technology with labor efficient practices to achieve world class productivity levels and low initial cash costs of about US $0.35/lb copper. Development procedures for the almost 800 million ton oxide deposit, as well as the hydrometallurgical processes selected for recovery of the copper values are discussed. Construction costs and pertinent technical data are shown.

Jan 1, 1996

By E. O. Mixon, Jack D. Kennedy

INTRODUCTION This contract is the most northerly portion of the Metropolitan Sanitary District of Greater Chicago's Tunnel and Reservoir Plan. (TARP) The project begins at Addison Street in Chicago and proceeds northerly approximately ten miles to end at Wilmette Harbor and Lake Michigan. The project which consists of 2 work shafts, 32 drop shafts, 7.322 km (24,020 ft.) of 6.7 m (22 ft.) diameter circular rock tunnel, 8.458 km (27,750 ft.) of 9.2 m (30 ft.) diameter circular rock tunnel and miscellaneous rock bolting and grouting, was bid for a total cost of $63,140,480. The tunnel invert elevation varies from 65.5 m (215 ft.) to 77.4 m (254 ft.) below the ground surface, which places the tunnel in a rock formation of dolomite limestone. At the tunnel invert, the unconfined compressive strength of the limestone varies from 96 MPa (14,000 psi) to 152 MPa (22,000 psi). The 6.7 (22 ft.) diameter tunnel required the mining of 10.9 cu m. (14.2 cu yd.) of rock per lineal foot of tunnel while the 9.2 m (30 ft.) diameter tunnel required the mining of 20.1 cu m (26.3 cu yd.) of rock per lineal foot of tunnel. The total cubic meters of rock required to be excavated from both tunnels was 818,821 cu m (1,070,978 cu yd.). All of this will be mined by tunnel boring machines (TBM). These tunnels were not to be lined with concrete. The thirty two drop shafts have upper portions that are cylindrical in the overburden and rock sections. They were divided into two groups, depending on diameter, with a different construction method for each group. The first group consisted of twenty three of the

Jan 1, 1979

Though the mining industry is beset with problems-a broad slump in metal prices, a rash of acquisitions and takeover attempts, rising capital costs, and an aggressive Canadian energy program-there was an under-current of optimism at the 1981 AMC conference that's been missing at industry meetings in recent years. The industry anticipates a turnaround in the 1980s, buoyed perhaps by the new spirit of cooperation from the Reagan administration. For the first time in years, it appears that Washington and the mining industry share mutual goals for developing the nation's resources. A number of prominent Reagan officials were on hand during the three-day conference in Denver, September 28-30, to reassure conferees that restrictions plaguing energy and minerals development would be eased. Interior Secretary James Watt and other government speakers promised cooperation in bringing balance to federal public lands policies, a review of regulations that have hampered the industry, and prompt action on domestic minerals policy. Daniel N. Miller, Jr., assistant interior secretary for energy and minerals, said, "It is our intent to dismantle the overhearing bureaucracy that has stifled mineral and energy exploration. We know that Interior's rules have shackled the mining industry in recent years, and we know that those rules must be eased." Miller noted that the administration will not permit mining on national park lands or wildlife refuges, but added that "we must assess a variety of uses of public lands ... we will restore lands to multiple use where practical." EPA administrator Anne Gorsuch assured industry representatives that the administration intends to work within environmental laws and with Congress to review and revise water, soil, and air pollution policies. "We have a strong commitment to see that there are major mid-course corrections" of air regulations, Gorsuch said. Support from these "new friends in Washington" will be crucial in light of the serious problems pressuring the industry. Copper prices have plunged to almost three-year lows and prices for molybdenum, gold, and silver have slumped. Earnings are down and today's high interest rates prevent a quick turnaround. Companies are on edge after the recent takeovers of Kennecott, St. Joe Minerals, and Texasgulf Though the companies may benefit from the major injection of capital that large energy firms can provide, many observers fear the new parent companies won't be willing or able to survive the cyclical metal markets. Arco and Gulf Resources, for example, have been criticized for closing Anaconda's Montana copper facility and the Bunker Hill unit in Idaho, respectively. Canada's national energy program has brought additional pressure on the industry. This policy, which emphasizes Canadian majority ownership of the country's energy sources, resulted in acquisition of Texasgulf's Kidd Creek lead-zinc-silver complex by Canadian and French interests. In response, the American Mining Congress adopted two resolutions on takeovers. One calls for the US government to review laws regulating tender offers and takeovers "to better ensure that principles of fairness and sound investment policy govern such transactions.'' The other asks the government to demand "fairness and reciprocity" as a basis for US policy governing international trade in minerals and investment relations with other countries. AMC's shopping list included four other priority goals, aimed primarily at the Interior Department: • Prompt implementation of Interior's efforts to bring order and balance to rules governing access to public lands for exploration and development. • Statement by the President of a comprehensive and coherent domestic minerals policy. • Amendment of the Clean Air Act to remove impediments to productivity and barriers to economic development that are not necessary to essential goals of the act. • Development of new approaches to better achieve worker health and safety in the most cost-effective manner without penalizing productivity. Almost 6000 mining industry executives attended the 1981 convention-the largest in AMC's 84-year history. As in years past, the conference offered a wide spectrum of presentations-nearly 100 papers in 26 sessions-ranging from commodity forecasts to the latest technical achievements. New Administration Stockpile Goals The minerals availability session included a presentation on management of the minerals stockpile by Paul K. Kruege r of the Federal Emergency Management Agency. Krueger notes that rather than providing incentives for development of a domestic raw materials industry, the government has "a history of providing disincentives to industry." In mining industries, he adds, the rate of productivity growth has been -6% over the last six or seven years. Krueger feels there will be a major change under the Reagan administration. In March 1981, FEMA began the first purchase program for the national defense stockpile in over 20 years. The stockpile is sadly out of balance, Krueger adds. Stockpile materials are

Jan 12, 1981

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By A. R. Conroy

Microscopic observation of physical and chemical changes which take place in various materials under conditions of elevated temperature and controlled atmosphere can often yield valuable insight into the fundamental physical-chemical reactions which control processes in which these materials play an active role. The technique of high-temperature microscopy thus becomes an important tool for basic and applied research in pyrometallurgical and allied fields. Investigators have long been aware of this and through the years have applied the technique to a wide variety of problems. However, up to this time, application has been on a rather limited scale due to the high initial cost of equipment and the relatively low rate of production of data resulting from the complexity of the apparatus and attendant problems in manipulation.

Jan 1, 1964

By R. C. Emmett

Waste treatment in the mining industry is by no means a new problem to this field. In a sense, the entire process from ore to finished product is one of waste treatment - the separation of a relatively minor quantity of desired component from valueless material. Where it has been necess-ary or economical to practice conventional waste treatment or pollution control methods, such as dust collection, water recovery from tailings, or impounding of residues for future treatment, this has been done. Generally the containment of hazardous pollutants such as arsenic and cyanide also has been followed in modern times. But it is only recently, with the public outcry for the elimination of all forms of pollution, "that the industry has been forced to solve what often appears to be a myriad of difficult and costly waste treatment problems, or be faced with the alternative of closing down the operation. It is the objective of this paper to describe new as well as conventional approaches to these problems, specifically as might be applicable to liquid-solids separation methods. Host wastes in the industry are present either as solutions or slurries, or can be most advantageously handled by conversion to this form, such as in scrubbing noxious gases and dusts with water. Separation of the solids and purification of the aqueous effluents are, therefore, often the principle problems.

Jan 1, 1971

By A. Newman, A. Brickey

Although some of the prevalence of openpit production scheduling software can be explained by the predominance of openpit mining throughout the world, other factors have led to a lag in corresponding underground software. We explain mathematically why underground production scheduling is more difficult than its openpit counterpart and provide directions for research in the underground scheduling arena.

Jan 1, 2014

By A. Newman, A. Brickey

A pesar de que parte del predominio de software de programación de producción a cielo abierto se puede explicar por la preponderancia de la minería a cielo abierto en todo el mundo, hay otros factores que han dado lugar a un retraso en el software subterráneo correspondiente. Explicamos por qué matemáticamente la programación de la producción subterránea es más difícil que su contraparte a cielo abierto y daremos pautas para la investigación en el campo de la programación subterránea.

Jan 1, 2014

By Bobby P. Faulkner

Allis-Chalmers has combined a new heat transfer device, called the ROLLER GRATE, with a unique processing scheme, resulting in the ROLLER GRATE Oil Shale Processing System of Allis-Chalmers. In order to test both the process and the equipment, a batch Process Development Unit (PDU) ROLLER GRATE retort was designed and built. This unit vas designed with the flexibility to process shale over a wide range of test conditions in order to demonstrate the attributes of the oil-shale processing system. Instrumentation on the PDU and extensive sampling of the effluent streams permitted the PDU test data to be used in the design and scale-up of the process. Over 30 tests have been conducted with Colorado shale, and over 25 tests have been run with an Indiana shale. In addition, rests have been run with California and Utah tar sands.

Jan 1, 1983

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015

By J. K. Whyatt

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations of in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence from the Lucky Friday Mine collected by U.S. Bureau of Mines researchers, as well as a review of case studies, demonstrates that in situ stress variations affect the spatial distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies, they are too expensive and, depending on conditions, may be too difficult, to use routinely in mapping stress variations. However, information from borehole and raisebore breakouts; deformation of mine openings; and patterns of seismicity, ground control problems, and rock burst damage can be used to build a stress database. This database can then be used in con-junction with maps of mine structure and geology and models of rock mass behavior to build a map of in situ stress variations. Such a map provides a means to anticipate patterns of mining-induced seismicity that are likely to be encountered and, hence, provide a means for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1995

By Irwan Halim, Seung Han Kim

This paper will describe design of precast segmental tunnel lining for the Pawtucket CSO Tunnel Project in Providence, Rhode Island. The tunnel is 11,700 LF long with 30-foot finished diameter to be constructed in complex sedimentary rocks. Special features of the segments include a large keystone and no connector used on radial joints. The typical segments will be steel fiber reinforced, and hybrid segments with additional steel rebars and shear bicones will be used around the adit openings without use of any structural framing. The important design considerations will be discussed, including special 3D segment to adit connection analyses performed.

Dec 1, 2022

By D. M. Abbott

The problem with best practices occurs when they do not work. This happens when the seldom-stated assumptions underlying the practice are not met. This paper provides some examples for the mining industry: (1) when core splitting is inappropriate, (2) when the use of fire assays for placer samples is inappropriate, and (3) when high-grading may be acceptable. Geologic conclusions are, in the final analysis, expressions of judgment predicated upon knowledge and experience. A geologic conclusion, however, purports to be more than an arbitrary determination—it is reached as a consequence of method. No specific method is required, but the method used must be an orthodox method, in accordance with orthodox definition of terms, and the one best adapted to the dealing with the questions asked about the property in question. Whether the so-called “best practice” is really applicable to the job at hand must be decided on the basis of professional scientific judgment. When one decides to deviate from a published “best practice” for sound scientific reasons, describe in detail in the report what the so-called “best practice” is, why it was inappropriate for the project, and why the method used was better. If one becomes aware that a “best practice” is being proposed, actively urge those proposing it to include in its description the underlying assumptions that must be met in order for the “best practice” to be valid.

Jan 1, 2014

By Raja V. Ramani

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas which have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and many other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1983

By Leonard Sugin

As we approach the end-of the 20th century we are made more aware of the tremendous role that energy plays both directly and indirectly in our varied way of life. The industralized nations of the world have already established industries and economies which are greatly dependent upon the availability of energy. The underdeveloped and developing nations of the world are slowly and surely moving to the same utlimate requirements. The world wide need for distribution of energy sources is continuing to grow. At the present time there is a great imbalance between the sources of energy and the consuming economies In order to bring about greater equality between supply and demand major efforts and large capital expenditures are constantly being made. Industralized areas are seeking their own independent sources of energy whereas those areas of the world which contain great reserves of energy are limiting its export as well as developing its own industralized capacity. Nevertheless, energy bearing materials are still transported great distances in order to satiate the appetites of power hungry economies.

Jan 1, 1975

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By John C. Brower

The purpose of this paper is to examine the Gays in which- the policies of the U.S. government, mining companies and third world countries affect each other with regard to the availability of minerals. The interaction involves U.S. policy towards the mining industry, the policies of the companies themselves, and the policies of third world countries towards the U.S. and multinational companies. It is assumed in this discussion that U.S. policy will continue to be to seek certain minerals from abroad rather than attempt to develop domestic sources for all its requirements. This would seem to make sense both from the standpoint of cost, and for preserving what domestic resources there are so as to maintain some degree of market leverage. In today's jargon, this means greater dependency on the "third world", which, for this discussion, includes virtually all the nations in Africa, South America and Asia. Concern for availability raises the important distinction between dependency and vulnerability, and as the Director of the Bureau of Mines has pointed out, the two are not the same. Dependency is not neccessarily a bad thing; it is vulnerability that counts (Norman, 1980)

Jan 1, 1982

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

Updating the openpit vehicle transportation network has the problem of being time consuming and low precision. To address this problem, a high-precision road network model construction method for unmanned vehicles in openpit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3+C (DeepLabv3+Concat) is presented, and the road information extracted by the DeepLabv3+C network is used to construct a three-dimensional model of the openpit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicles meeting in openpit mines, a vehicle meeting strategy is proposed. This strategy is used to guide the navigation of unmanned vehicles in openpit mines. At the end of the study, vehicle running simulation was carried out on the road network model using Unity, a 3D visualization simulation software. The high-precision unmanned road network model of openpit mines studied in this work can further promote the construction and development of smart mines by acting as a high-precision map for unmanned vehicles.