Search Documents

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Cameron Mitchel

Brow hazards are a significant concern in coal mine ribs and form when weak coal sloughs out of a rib face and exposes an overhanging block of more competent rock or coal. Of 36 rib failure fatalities in the last two decades, 36% resulted from rib brow failures. This highlights the need to better understand the mechanisms driving brow formations and failures to mitigate this hazard and eliminate potential fatalities. The research team at Missouri S&T worked to enhance the current CPRR system and include the potential for these brow hazards. We employed physical modeling methods to build a scaled model from critical brow cases observed in the field. The dimensions and properties of the models were scaled down by 14.4 times from the field cases. The results of the physical modeling efforts were used to assist in calibrating distinct element numerical models vital to understanding brow formation and failure mechanisms. Subsequently, three physical models were created and tested to provide data on an otherwise impossible-to-capture event at the field scale. The results of these tests provided formed brow dimensions that agree well with those observed at the field scale. The brow dimensions were 1.25 inches deep into the rib, equivalent to 1.5 feet when scaled up. Similarly, the numerical modeling efforts provided good agreement by capturing a brow forming 1.55 inches deep into the rib. The physical model results further validate the applicability of physical modeling efforts for capturing otherwise difficult and dangerous phenomena in a controlled lab setting.

Feb 22, 2026

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The recovery of iron from low-grade (31.6% Fe) Muro iron ore was investigated using reverse anionic flotation of quartz. Tests were performed to investigate the effect of pH, the effects of using distilled vs. tap water as the flotation medium and the effects of using cassava starch vs. dextrin for the depression of iron minerals. The optimum results were obtained around pH 10 and 11, and cassava starch was superior to dextrin in depressing iron oxides. Investigations at pH 11 using cassava starch and distilled water resulted in a concentrate grade of 69.4% Fe with a recovery of 84.4% Fe. Under the same conditions, the use o f dextrin produced a concentrate grade q f 65.9% Fe with a recovery of 78.6% Fe. Investigations at pH 10 using cassava starch and distilled water resulted in a concentrate grade of 60.2% Fe with a recovery of 83.9% Fe, and under these conditions the use of dextrin produced a concentrate grade of 56.1 % Fe with a recovery of 81.5% Fe. Flotation studies conducted at pH 11 using tap water and cassava starch resulted in a concentrate grade of 70.4% Fe with a recovery of 92.7% Fe. This demonstrated the superiority of tap water over distilled water in the reverse anionic flotation process. Investigating the effect of calcium ions on the activation and flotation of quartz with oleic acid revealed that a calcium ion concentration of 50 to 100 ppm was optimum.

Jan 1, 1996

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is becoming recognized by more persons responsible for materials management as consultants, at the corporate level and at the plant level. They have learned that the economic advantages of a pneumatic system are frequently decisive when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection. (1). The main disadvantages of a pneumatic system is the greater horsepower required per unit weight of material conveyed and material limits in abrasiveness and density. In addition, there is a tendency to increase material breakage at changes of direction and at any obstruction such as the imperfect butting of one, piece of pipe to another in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 pounds per cubic foot tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 and 20 pounds per cubic foot can be handled with less problems but flow rate is hard to predict. The 20 to 60 pounds per cubic foot range offers best results; whereas, over 60 pounds per cubic foot, materials tend to drop out of the air stream and settle in the pipe line unless careful provisions are made to prevent it. (2).

Jan 1, 1967

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By Dan Urich

This paper covers the construction and operation of the Grate-Kiln system at the Humboldt Mine. The mine concentrator and pellet plant are located approximately 14 miles West of Ishpeming, Michigan, on the Marquette iron Range. Production of pellets began in mid-July, 1960.

Jan 1, 1962

By Daryl L. Gusey, John T. Neubert, Matthew A. Sares

The Colorado Geological Survey completed an inventory of environmental degradation associated with abandoned and inactive mines on National Forest System lands in Colorado. In the course of the inventory, areas with naturally occurring acid rock drainage were also noted. Approximately 18,000 abandoned mine- related features were inventoried, including about 900 features that are considered significant enough environmental problems to warrant further investigation. Water quality data, such as pH and conductivity were gathered at all features where water was present, such as draining adits, seepage at the toe of dumps and tailings, and standing water in shafts. Samples were taken where field tests indicated low pH andlor high conductivity, including several areas with naturally occurring acid rock drainage. Samples were analyzed for dissolved and total metals, and for selected anions. All mine locations and data collected by the field geologists were entered on field forms and, subsequently, into a computer database and GIS format. With the information provided by the inventory, the Forest Service, in cooperation with other agencies, has been able to prioritize abandoned mines for reclamation. In most cases, cleanup is approached on a watershed basis. Mines in priority watersheds have been selected for reclamation first. Watersheds where studies prerequisite to cleanup are occurring include the upper Anirnas River, Willow Creek (tributary to the upper Rio Grande), Chalk Creek (tributary to the upper Arkansas River), the Uncompahgre River, and the Alamosa River. During the inventory, evidence of naturally occurring water quality degradation was found in areas where little or no evidence of mining activity exists. These areas include the upper Alamosa River, the Middle Fork of Mineral Creek, Peekaboo Gulch, and Handcart Gulch. Water from these natural sources has been found to significantly exceed Colorado water quality standards for several metals.

Jan 1, 2000

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By D. M. Neil

Road-headers are one of the most popular mechanized excavators used in mining and civil under-ground construction. These machines are primarily used in soft to medium hard rocks. This paper reviews the parameters associated with the application and operation of road-headers and presents a method for estimating cutting performance.

Jan 1, 1994

By Theodore H. Eyde

In 1971, the Minerals Division of The Superior Oil Company acquired exploration rights to an unpatented claim group in the Superior (Pioneer), Arizona mining district, lying west of the Concentrator fault. This major post-mineral fault displaces the Magma vein-fault, which is mined in the Magma Mine at Superior, Arizona. The Magma vein-fault and the enclosing section of pre-mineral rocks consisting of Paleozoic and younger Precambrian sediments and diabase, is overlain by a thick section of post-mineral rocks, consisting of the Gila conglomerate, the Apache Leap dacite, and the Whitetail conglomerate. Geologic information on the thickness and attitudes of the rocks obtained from previous diamond drilling indicated that the section of post-mineral rocks might be from 3,000 to over 4,010 feet thick in the target area. (Figure 1) The Magma vein-fault is a steeply dipping vein which has produced nearly a billion dollars of copper, zinc, silver, and gold. It has been mined continuously for nearly 10,000 feet along the strike and nearly 5,000, feet vertically down the dip. It ranges from less than a foot to over 50 feet wide and contains sulfide mineralization con¬sisting of pyrite, chalcopyrite, bornite, and chalcocite.

Jan 1, 1973

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By T. Kawashima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service port construction, transshipment and environmental control. The major problem is the transshipment of coal. Customary methods for bulk transfer must be improved and/or new systems developed. Slurry unloading has a key role in the new systems. The present report reviews progress in slurry transportation research which has been done in Japan since the 1960s when large scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are discussed.

Jan 1, 1982

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By Eugene R. Palowitch, Albert W. Deurbrouck, Thomas H. Parrsons

INTRODUCTION Hydraulic concentrators utilize the physical characteristics-size, shape, and specific gravity-of particles suspended in a fluid medium to effect a concentration of desired quality. Fine-coal concentrators include generally those devices which are used to clean roughly 3/4, in. (9.5 mm) top-size coals. While this size designation is somewhat arbitrary, it is consistent with current practice although some fine- coal concentrators can treat coarser coals effectively. A variety of devices have been and are currently being used to wash fine coals and include: dense media cyclones, wet concentrating tables, hydrocyclones, jigs, spirals, launders, and upward-current classifiers. As launders and upward-current classifiers have been replaced by more efficient devices, they no longer warrant consideration as fine-coal washers. And as fine-coal jigs were addressed with the Baum jig under Part 1, Section 2, and heavy media cyclones and hydrocyclones were addressed under Part 2, Section 1, of this Chapter, only the wet concentrating table and the spiral concentrator will be discussed here. WET CONCENTRATING TABLES History The current wet concentrating table evolved from continuous belt concentrators which utilized a flowing film of water to recover heavy metals. In these devices the heavier concentrate moved up the inclined plane of the belt while the lighter impurities were washed away by water flowing down the belt. The natural outgrowth of the continuous belt concentrator was the vanner, a vibrating endless belt which was first developed about 1860 by Hartwig. Later models of the vanner, such as the Frue, incorporated oscillation in a plane transverse to the direction of the water current. Excellent descriptions of these washers are found in The Cleaning of Coal, by Chapman and Mott.80 Further development of tables included the circular stationary table (Linkenbach), the multiple round table (Anaconda-Evans), the bumping table (Campbell), and finally the differential-motion table which is now used extensively for cleaning fine coals.

Jan 1, 1991

By Daniel C. McLean

Many of the major copper ore bodies throughout the world contain chalcocite (79.9% Cu) as the principal copper mineral, yet the grades of copper concentrates produced from these ores rarely exceeds 25 to 28% Cu and in one known instance went as low as 13%. The low grade has traditionally been attributed to the presence of "activated pyrite" and/or chalcopyrite, and the universal approach has been excessive regrinding with all of its inherent effects-high capital, energy and maintenance costs, excessive sliming, and concentrate filtration difficulties (high moisture content). E. P. Cadwell, former Chief Metallurgist for American Cyanamid Company, did extensive microscopical studies on several of these types of concentrates from South American operations during the 1950's and discovered they all had one common feature--the pyrite particles in the concentrate were all rimmed with thin films of secondary chalcocite or covellite. As far as a flotation bubble or reagent is concerned, a rim of chalcocite is the same as a solid particle of chalcocite, and as long as a rim is present, the particle is going to float. Upon examination of these rimmed particles under the microscope, it becomes quite obvious why regrinding will never solve the problem and why maximum increases in grade by this technique rarely give improvements in grade of greater than 3 to 5% Cu.

Jan 1, 1983

By Peter Schmäh, Tobias Engel

The E-Power Pipe technology was originally developed for the trenchless installation of protective pipes and pipelines of 10" to 28" diameter, over long distances of more than 4,000 ft. The twostage process combines elements from Horizontal Directional Drilling (HDD) and microtunnelling technology. A microtunnelling boring machine (MTBM) excavates the borehole using a specially designed, temporary jacking pipe. A Rack & Pinion jacking frame pushes the equipment during the pilot bore and pulls in the prefabricated pipe string in a second step. The slurry microtunnelling machine is equipped with a jet pump, creating the so-called AVNS machine type. A new generation of small hard rock cutting wheels complements this considerable achievement for the tunnelling industry

Dec 1, 2022

By Robert E. Goodwin

As man's need for minerals continues to grow and as the known mineral deposits become depleted, it may be expected that these increased demands will result in greater exploration for additional deposits and at continually increasing depths below the earth's surface. As labor and material costs continue to rise, the need for more economic material handling will be emphasized. The quest for heavier payloads, safely moved at faster speeds from deeper mines, will be vigorously pursued. Strenuous efforts are, therefore, being made in the wire rope industry to develop ropes with greater strength-to-weight ratios than presently available while maintaining the dependability and long life being received from the conventional rope manufactured today. For many years, high quality rope wire has been manufactured from rods of selected steel compositions. Carefully-controlled wire drawing combined with proper heat treatment has resulted in high quality wire and wire rope throughout this period. Refinements in the rod produced from specially-selected high carbon steels combined with the latest improvements in wire drawing and heat treatments have made it possible to manufacture higher strength rope wire of uniform composition and structure that is suitable for use in Special High Strength wire rope.

Jan 1, 1970

By P. G. Tzeferis

Factory beet molasses media were used as cheap sources of sucrose for microbial leaching of Greek nickeliferrous laterites using strains of Penicillium and Aspergillus sp. Nickel recoveries of up to 62% and cobalt recoveries of up to 50% were obtained by leaching in a two-phase system in which bioacids were produced by fungal metabolism in molasses ferrocyanide pretreated media. The addition of potassium ferrocyanide to the molasses substrates prior to leaching was found to have a beneficial effect by increasing the level of citric acid bioproduction, thus improving the leaching efficiency of the fermentation liquid. The metals known to interfere with citric acid production (i.e., Fe, Cu, Ca and Mn) were those most efficiently precipitated. Considering the much lower commercial price of molasses in the industrial market compared to sucrose and glucose carbohydrate media, molasses could prove to be a promising alternative, despite the cost of the required pretreatment.

Jan 1, 1995