Search Documents

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By Charles A. Beasley

Coal conversion to electricity or to substitute natural gas requires a significant quantity of natural and human resources including, in addition to the coal resource base, land, water and the construction and operating labor force. Each method of coal conversion has its advantages and disadvantages relative to conversion efficiency, preferred method of resultant energy transportation, resources consumed, and impact on the environment. Regulations which have been passed in recent years to maintain or restore the pre-project environment can add significantly to the capital and operating costs of both a conversion facility and its associated mine.

Jan 1, 1983

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978

By R. M. Powers

The Florida Institute of Phosphate Research (FIPR) has funded a four-year research project to develop a computer model 'which will predict the hydrologic impacts of phosphate mining on surface and groundwater systems. The core of the model is an analytical geographic information system (SPANS) which integrates EPA's Hydrology Simulation Program Fortran (HSPF) surface water model with the McDonald-Harbaugh groundwater model (MODFLOW). The hydrologic model conducts both event and continuous annual Simulations driven by variable precipitation and temperature data. The model is currently being calibrated and will be ready for distribution to the user community in mid-1991.

Jan 1, 1990

By J. A. Lombardi

"EXECUTIVE SUMMARY The use of membranes for the treatment of Acid-Mine-Drainage (AMD) water has been a 35 year mining industry quest that has only recently produced commercial scale Zero-Liquid-Discharge (ZLD) plants. The process of development of the membrane treatment of AMD has been defined by the water treatment industry’s efforts to control gypsum scaling of the membranes, an artifact of the concentration of calcium and sulfate ions on the concentrate or “brine” side of the membranes. Improved anti-scalants, changes to membrane surface geometry and a lowered permeate flux rate were all part of solving the calcium sulfate (gypsum) scale formation problem. Whether used singly or as part of a multi-stage membrane treatment process, the production of “left over” membrane concentrate or brine, in any volume large or small, was a second barrier to adoption of the method by the mining industry. The two identified “final brine” treatments were a) solar evaporation ponds and b) mechanical evaporators. Brine disposal by solar means is typically site limited to flat terrains or high net evaporation locations. Mechanical evaporation-crystallization is applicable at all sites but, typically, at onerously high ownership and operating costs. Miwatek, a South African water treatment start-up, has entered the mining AMD ZLD marketplace with two new, pilot-scale tested, processes, both of which are predicated on the innovative treatment of a reasonably concentrated AMD and neither of which produces a final brine that requires disposal. In the Miwatek Brine Treatment, MBT, method the membrane brine is caustic pH adjusted and de-calcified precedent to passage through a second membrane plant. The caustic is generated on-site by a lime treatment of the second-membrane concentrate. The first- and second-stage permeates are blended for discharge. The process usually yields no “final brine” for disposal. In the Miwatek Ettringite Treatment, MET, method a low pH first-stage membrane brine is lime treated in two or three steps in the presence of aluminum in a way that metal hydroxide and calcium sulfate solids are formed and purged from the system. Sufficient aluminum is often present in the feed water to, with judicious recycling, enable operation of the lime-aluminum treatment without the purchase of outside aluminum reagent. The first-stage membrane permeate is blended with the lime-aluminum treated membrane concentrate for discharge. The indications are that the method can comfortably meet the low 250 -500 ppm SO4 discharge water quality standards that have most recently been proposed in South America. The process yields no “final brine” that requires disposal. Projected own-operate costs for the MBT and MET systems are less than the estimated costs for all identified alternative treatments."

Jan 1, 2015

By M. S. Safarzadeh, V. Agarwal

"The solvent extraction of cerium(III) and samarium(III) from mixed solutions of all rare earth elements (REEs) except promethium using PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), an acidic extractant, was investigated. The effects of aqueous equilibrium pH, various acids (sulfuric acid (H2 SO4 ), hydrochloric acid (HCl) and nitric acid (HNO3 )), initial metal ion concentration and extractant concentration on the solvent extraction of Ce(III) and Sm(III) were systematically studied. From the experimental results, HNO3 and HCl were found to be the preferred aqueous media for the solvent extraction of both Sm(III) and Ce(III). The most promising experimental conditions of pH, PC88A concentration and metal ion concentration were identified for the extraction of Ce(III) and Sm(III). Separation results showed that H2 SO4 at pH 2 provided the best separation between Sm(III) and Ce(III). IntroductionIn recent years, demand for rare earth elements (REEs) has increased significantly because of their many commercial applications. REEs have especially important high-tech applications owing to their unique physical and chemical properties, and they are used in a wide range of areas such as catalysts, ceramics, magnets, lasers, glass, neutron absorption and alloys. As REEs have very similar physicochemical properties, their separation and purification from each other is challenging and gaining significant interest. Samarium (Sm) and cerium (Ce) are found in different REE minerals, including bastnäsite ((Ce,La,Nd(CO3)F), xenotime (YPO4) and monazite ((Ce,La,Nd,Th)PO4) at major production sites in the United States and China, as listed in Table 1 (Bleiwas and Gambogi, 2013). The most common acidic organophosphorous extractants used for REEs extraction and separation are DEHPA (di-(2-ethylhexyl)phosphoric acid), PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) and Cyanex 301 (bis(2,4,4-trimethylpentyl)dithiophosphinic acid) (Sarangi, Reddy and Das, 1999; Surampally et al., 2012; Tian, Jia and Liao, 2013). Out of these extractants, PC88A is known for providing higher separation factors (Acharya, Mishra and Misra, 2015). El-Hefny et al. (2010) investigated the kinetics of the solvent extraction of Sm from chloride media using sodium salt of Cyanex 272 and reported the extracted species to be Sm(OH)A2•2HA. Lee et al. (2005) investigated the solvent extraction of Sm(III) with PC88A and saponified PC88A from chloride solutions and found the stoichiometry of the extraction reactions to be 1.5 with PC88A and 3 with saponified PC88A."

Jan 1, 2017

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device. Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery. Recent developments-in electrooptic inspection of dry end wet material leaving a grinding device are critically reviewed. New methods for characterizing ultrafines are discussed. A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine index and other fineness indices is described.

Jan 1, 1983

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

By R. Hogg

The various sub-processes which, together, make up the unit operation of froth flotation all depend on the characteristics of the feed solids, the solution phase, the air bubbles and the mechanical/hydrodynamic action of the machine. Characterization is obviously necessary for evaluation and process control, but the relationships between characteristics and process response are often unclear. A model-based characterization scheme is proposed in which material and system characteristics are evaluated in the context of simplified models for the individual subprocesses. The general basis for such an approach is discussed using the process of particle attachment and the influence of mineral liberation as examples.

Jan 1, 1989

By Xiaochun Xiao, Xin Ding, Yishan Pan, DI WU, Xiangfeng Lv

Rockburst is a sudden disastrous instability of coal mass that poses a serious threat to underground exploitation of coal resources; therefore, approaches of prediction and control methods are valuable for improving mining environments. The mechanical properties and bursting liability of coal with drying, under-saturated, and saturated moisture content under uniaxial compression are investigated, and the charge induction signal during coal deformation both in the laboratory and on-site is recorded in this study. The presence of water reduces the cohesion and increases the internal stress caused by non-uniform deformation of minerals, resulting in the strength, elastic modulus, and bursting liability being weakened. The charge induction precursor main frequency band is 1–100 Hz and belongs to the very-low-frequency signal regime, and it indeed varies with the loading stage, leading to specimen failure owing to changes in amplitude and continuity of the charge pulse in both the time and frequency domains. Water inhibits the richness of charge induction and reduces the bursting liability, and the earlier the precursor appears, the more total charge emerges. Moreover, measurement results indicate that the amplitude and continuity of the charge pulse decrease over a longer time, as recorded in a coal seam with water injection, further verifying the weakening of the coal dynamic characteristics. Charge induction can be a valuable tool with which to obtain the precursors for rockburst and to aid the evaluation of water injection.

Dec 26, 2022

By J. C. Motz

During the past five years, Rexnord has developed, tested and introduced the Nordberg Omnicone Crusher to the industry. When the Symons brothers invented the cone crusher over 60 years ago, they employed the principle wherein the length of the crushing stroke was related to the free fall of material by gravity. This permitted the material being crushed to fall vertically in the crushing chamber; and in effect, caused the particles to be crushed in a series of steps or stages as the particles got smaller due to the crushing action. This also helps to reduce the rate of wear of the liners since the sliding motion of the particles is minimized.

Jan 1, 1986

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991

By J. F. Oyler

One of the most important applications of material handling engineering technology occurs in iron ore pelletizing plants. Although the total installed value of material handling systems in such plants, as well as in many other modern process plants, is a relatively small percentage of the value of the plants (5 to 10% perhaps), their significance is considerable. Indeed this significance equals that of the more expensive process equipment in the plant, since the failure of any component of any system causes, shutdown of the entire plant. It is because of this increased consequence of failure that design criteria for process plants are more conservative than for conventional material handling applications. A second unique characteristic of material handling technology applied to process plants in general is the variety of materials being handled and the wide range of problems this variety presents. One extreme encountered is the stickiness of filter cake. Here the entire design effort is aimed at keeping the material flowing through transfer points and preventing it from building up on components. Another extreme is the conveying of fired pellets - hard spheres with a very flat angle of repose and abrasive characteristics severe enough to make conventional wear plate materials impractical.

Jan 1, 1976

By Richard Thomas Newcomb

The trend towards proportionately rising volumes of surface mining through- out the world and especially in the United States has led some observers to predict that the future of underground mining is quite limited. Certainly, the simple extrapolation of current trends1 gives evidence of a compelling sort for the hypothesis that technological progress is proceeding at a faster pace in surface than in underground mining. This paper attempts to examine the basis for these predictions by searching the historical record on differential rates of productivity as these are observed in iron ore and coal mining. In recent years economists have discussed "technology gaps" among industries or segments of the same industry, by which they mean that mechanisms for invention and its diffusion are faulty or retarded in such a way that feasible cost-cutting innovations are not applied or developed, even though technicians regard them as practical.2

Jan 1, 1968

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022