Search Documents

By J. Morris, R. Sellaro

El petrodiesel es un colector común para la flotación de carbón, pero la partición de compuestos orgánicos de diesel (DRO por sus siglas en inglés) en corrientes de proceso no ha sido ampliamente estudiada. Investigaciones preliminares sugieren que bajo esquemas de dosificación normales los contenidos residuales totales de DRO en aguas de procesos deben estar limitados a la fracción soluble en agua (WSF por sus siglas en inglés) sub-ppm. Es más, los hidrocarburos aromáticos poli-cíclicos (PAH por sus siglas en inglés) debería segmentarse de manera proporcional con los compuestos orgánicos de diesel (DRO). El propósito de este estudio fue confirmar estos resultados en pruebas de flotación realizadas en laboratorio. Se midieron los contenidos totales de DRO Y PAH en aguas asociadas con los flujos o corrientes de concentrados y relaves. Los resultados muestran que las aguas con concentrados tenían de manera consistente mayores cantidades de DRO que las aguas de relaves. Es más, los contenidos de DRO en ambos flujos generalmente se incrementaban con el aumento de la dosis de diesel. De acuerdo con la investigación preliminar, los DRO parecían estar limitados a la fracción soluble en agua (WSF) y los PAH tendían a segmentarse proporcionalmente con los DRO. Bajo condiciones de operación típicas, los DRO residuales no deberían representar una preocupación medioambiental, pero deben evitarse situaciones que permitan una sobredosis significativa de diesel.

Jan 1, 2014

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

By H. S. Duzgun, N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline’s long-term availability, to develop preventive maintenance plans and to make future projections about the dragline’s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, Page 736 and Marion 7820, which have been operating in the Tunçbilek openpit coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data and (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (15.29 m3) seemed to be more reliable and less likely to fail when compared with Marion 7820 (30.58 m3). The operating hours without failure range from 41 to 51 hours with 50% reliability.

Jan 1, 2011

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry as a tool to improve the efficiency of its processes, to reduce costs, but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios: lower ore grades, extreme weather conditions, deeper deposits, harder rock mass, and high-stress environments. This paper discusses the importance of innovation for the mining industry and describes the mechanisms by which it is carried out. It includes a review of the drivers and actors involved and current trends. The digital transformation process that the industry is going through is analyzed, along with other relevant trends that are likely to shape the mining of the future. Additionally, a case study is presented to illustrate the technical and economic implications of developing a disruptive innovation project.

Jul 23, 2020

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By Weiran Zuo, Jinsheng Guo, Chun Yu, Jinyu Zhan, Bao Guo

High-precision prediction of the target minerals’ content in the feed and concentrate products is vitally important for the efficient beneficiation of mineral resources. Visible and near-infrared (NIR) spectroscopy provides a cost-effective way for online measurement of the mineral content in an industrial process. In this investigation, simulated specimens consisting of five different types of minerals that are present in the copper oxide ore, malachite, quartz, calcite, hematite, and chlorite were prepared with a variety of malachite contents, and the mixed specimens were analyzed by a visible-NIR spectrometer in an integral sphere mode. The reflectance spectrum is used as input and the malachite content as output to build the prediction model. The obtained data was modeled by support vector machines (SVM), and a Grey Wolf Optimization (GWO) is proposed with the goal of improving the prediction accuracy. The GWO algorithm has been applied to adaptively search for the best combination of featured values. After cyclic comparison, the optimal penalty factors c and g can be quickly and accurately selected. The experimental results show that the SVM model established by the GWO algorithm has a better fitting effect and smaller prediction error, compared with other models.

Aug 3, 2023

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By J. Richard Kyle

The Pb-Zn ore bodies in the Pine Point district are localized in paleo-solution structures that developed as the result of post-middle Givetian subaerial exposure of the carbonate barrier complex. Sulfides are concentrated in transgressive pale-solution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character, one of which contained metals and the other reduced sulfur. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition. District and ore body metal distribution patterns may reflect the nature and movement of mineralizing fluids.

Jan 1, 1979

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By XUEWEN WANG, Changda Zhang, Huaguang Wang, Mingyu Wang, Bin Hu

The copper smelting process produces plenty of copper slag every year, which is a hazardous solid waste, but a secondary resource. In the present study, the extraction of copper, nickel, and cobalt from copper slag was investigated through the process of sulfation roasting–water leaching and the process of sulfation roasting–sulfate decomposition roasting–water leaching respectively. Compared with the process of sulfation roasting–water leaching, the process of sulfation roasting–sulfate decomposition roasting–water leaching is a better choice, which could not only get almost the same leaching of copper, nickel, and cobalt as the former process, but has a lower leaching of iron and aluminum. For the process of sulfation roasting–sulfate decomposition roasting–water leaching, the leaching of Cu, Ni, and Co reached up to 74.2%, 71.1%, and 69.6% respectively, under the optimal conditions including sulfation roasted with 80 wt% sulfuric acid addition at 200 °C for 60 min and sulfate decomposition roasted at 650 °C for 60 min, followed by water leached at 90 °C for 30min with a liquid–solid ratio of 2 ml/g. The leaching of Fe and Al was only 4.9% and 17.6%.

May 4, 2020

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By Gary E. McIntosh

This paper will discuss a U.S. Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring of shallow groundwater systems in the Basin. (2) Monitoring of the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems. (3) Development of a regional groundwater simulation model with appurtenant subroutines to determine local effects.

Jan 1, 1978

By I. Moreno-Ventas, G. Ríos, J. C. Fernández-Caliani, M. Bacedoni

"This paper delves into the constraints on the nature, origin and thermal evolution of the accretions formed in the uptake shaft of the flash smelting furnace operated by Atlantic Copper in Huelva, Spain, outlining recommended practices for preventing accretion buildup. The accretions were investigated using quantitative electron probe microanalysis, X-ray diffraction and digital imaging techniques, and the experimental data on mineral composition, crystal chemistry and textural relationships were interpreted in terms of thermodynamic phase equilibrium in the SiO2-Fe-O-S system. The results suggest that two distinct types of accretions were formed by the fractional crystallization of two coexisting immiscible melts, under changing conditions of oxygen partial pressure (pO2). The type I accretion of magnetite + delafossite ± cuprite ± tridymite ± metallic copper crystallized from a fractionating copper-rich melt at pO2 above about 10-5 atm, while the type II accretion of magnetite + fayalite + metallic copper + chalcocite derived from a melt with lower copper concentration when pO2 levels dropped below that critical level. Phase compositions and textures were consistent with a cooling history of both compositionally contrasting liquids from about 1,250 °C, the liquidus temperature of magnetite, to eutectic or near-eutectic temperatures of around 1,100 °C. The maintenance of appropriate temperatures — above the liquidus temperature of magnetite — and oxygen partial pressure levels may be critical for the prevention of accretion buildup. IntroductionCopper flash smelting with oxygen-enriched air, an autothermal process developed half a century ago by Outotec (Espoo, Finland), formerly Outokumpu, currently accounts for about 50 percent of the world’s primary sulfide-based copper (Schlesinger et al., 2011). The partial reaction of copper sulfide concentrates produces two separate molten streams, copper-iron-sulfide matte and iron oxide-rich slag, and releases sulfur dioxide (SO2) gas. The matte is sent to converters to remove the remaining iron and sulfur, leaving blister copper with grade of about 99.5 percent copper (Cu), which is cast into anodes for electrolytic refining.The SO2-rich gas generated by the oxidation of sulfide feed particles contains a significant proportion of dust that is entrained in the process off-gas. The gas from smelting is transferred into a waste heat recovery boiler, where it is cleared of dust and cooled before it is converted into sulfuric acid. If the process is not operated properly, the dust-bearing gas may form accretions between the uptake shaft of the flash smelting furnace and the waste heat recovery boiler, causing severe problems in the gas handling system (Swinbourne, Simak and Yazawa, 2002; Miettinen, 2008; Stefanova et al., 2012). Removing the dust accretions usually requires a greal deal of time, effort and resources. Understanding the buildup of accretion may help in reducing the problems and optimizing the process"

Jan 1, 2017

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By K. H. McDaniel

People are our most valuable resource. It is as true today as any point in mining history as we face unprecedented personnel shortages aggravated by a workforce that is aging, significant generational gaps and difficulties recruiting younger professionals all amidst increasing global mineral demand. The educational system has a similar, but slightly contrary problem. Many historically strong mining engineering programs have died. Now, fewer mining oriented universities are trying to produce more students in order to meet the demand. Moreover, their situation is aggravated by a similarly aging workforce, a general lack of mid-career PhD?s with the interest and field experience to teach effectively, an extremely slow hiring and funding process, and an inability to be competitive against private industry compensation packages. The traditional instructional model, while not necessarily broken, is most certainly dated, and can penalize programs and students where schools do not have in-house expertise in a given topic. Mining companies, like Rio Tinto, have the opportunity, if not necessarily the obligation, to positively influence how this model works. Educational Partnerships may be the key. This paper will address some observations, and possibilities, associated with Rio Tinto?s efforts in this area.

Feb 23, 2014