Search Documents

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By Patrick Ph. D. Kennedy, Osvaldo A. Ph. D. Bascur

With the revolutionary progress in information and computer technologies, applying the latest information technologies in metallurgical complexes has become a serious challenge to both a major opportunity and a serious challenge to both management and technical teams. The emerging component and object technologies are changing the way everyone can beneficially use their computer and networks to add to their corporate bottom lines. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All process equipment and control strategies require maintenance from local personnel at the mine. Integrated use of existing and emerging technologies is making it possible to implement an overall process effectiveness control index. This index is based on key indices such as losses due to plant availability, performance efficiency and rate of quality. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is highlighted. An emerging plant integration paradigm is described to simplify the implementation of business enterprise resources management and distributed plant management systems.

Jan 1, 1998

By John Keefner, Charles Kocsis, Kyle A. Scalise

Geotechnical modeling of mines is crucial for understanding the many factors that can pose potential hazards or limit production opportunities. The process of back analyses for modeling is often used, but in many instances, the back analyses can be cumbersome and time inefficient.While thesemodels and back analyses may be accurate, these types of back analyses may not be ideal to be used at mines and by engineers because the process is so time-consuming. This paper introduces event-based back analyses that utilize prior events to create more accurate models while eliminating large modeling time because the models are back analyzed from previous events. The completed analyses supply a more detailed insight into the potential hazards at Round Mountain, an open pit operation, as well as provide a better understanding of how improper risk analysis results in missed opportunities. The more we understand about mining activities and processes through modeling, the safer and more productive mines will be.

May 24, 2021

By G. Mei

"This study explores froth flotation and selective flocculation methods to recycle waste phosphors containing several rare earth elements, namely, yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb). The effects of the presence or absence of collector and of flocculant and their dosages, as well as the pH, were investigated. Reverse flotation resulted in concentrates with grade of 27.03 percent and recovery rate of 71.36 percent, while flocculation resulted in concentrates with grade of 31.43 percent and recovery rate of 91.28 percent. The flotation and flocculation behaviors were further analyzed by X-ray diffraction analysis, zeta potential measurements, particle size distribution and other methods. The successful separation of rare earth minerals by flotation was attributed to the selective adsorption of the collector onto quartz, making it particularly recoverable by reverse flotation so as to be separated from the valuable materials. The analysis of the particle aggregation process indicated that its better flocculation performance was due to the selective adsorption of flocculants onto the unwanted materials, enlarging the flocculant sizes by forming aggregations and facilitating the separation of rare earth minerals from waste materials based on different settling rates. IntroductionBecause waste phosphors pose the problems of heavy environmental burden and high risk to human health (Hu and Cheng, 2012) as a result of containing heavy metals such as mercury and manganese (He et al., 2006; Lucas and Emery, 2006), they have received added attention as urban mining resources for extracting rare earth elements (REEs) like yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb).At present, chemical processes such as acid leaching, alkali fusion, roasting and extraction are the primary methods for recovering REEs from waste phosphors (De Michelis et al., 2011; Li et al., 2012; Li, 2010). With these strategies, phosphors can be effectively decomposed and their REEs extracted. After the removal of impurities, the REEs can be efficiently precipitated by adding an H2C2O4 solution (Porob et al., 2012). Although relatively high recovery rates are achieved, those processes entail high energy consumption and can cause severe environmental pollution."

Jan 1, 2017

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation's energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By R. P. King

The MODSIM mineral processing plant simulator is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open-and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Jan 1, 1997

By K. E. Robinson

During operation of tailings impoundments, water is lost through decanting, evaporation and seepage. Techniques have been developed to regulate or control each of these components. Collectively implemented, these techniques form the basis of tailings impoundment management. Regulation of the rate and level of decanting influences the size of a free water pond, and, thereby, the amount of evaporation and seepage, which are both area-dependent. Conversely, the encouragement of seepage and/or evaporation could also be used to reduce decanting requirements. Management of one of the components of a tailings impoundment's water balance is reflected in changes in the other components. The seepage component has the greatest potential impact on the environment, and consequently requires the closest scrutiny. Water percolating through tailings backfill transports heavy metals and other dissolved solids from the impoundment into the local groundwater regime. Depending on the seepage volume and concentration of contaminants, seepage from impoundments could exceed environmentally tolerable limits. Once mobilized, seepage-borne pollution is much more difficult to treat, mainly because of the problems in collecting the diffusive transportation medium. Pollution abatement measures relative to tailings impoundment seepage depend on seepage prevention or reduction. Seepage control measures include constructing barriers to flow, pump-back systems of interception and restricting the supply of water available for seepage.

Jan 1, 1987

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By J. Hart, P. W. Conrad, S. Rosenthal, R. A. Hogan

The Mining Engineering Department at Montana Technological University (Montana Tech) has a new Mine Safety and Health Administration (MSHA) approved program for Part 46 and Part 48 mine health and safety training. The training program will utilize the facilities and faculty from Montana Tech’s Mining Engineering and Safety, Health, and Industrial Hygiene departments to provide superior mine health and safety training to the mining industry. The faculty of each department includes professionals with experience in safety training and the mining industry. The training program incorporates adult learning techniques and extensive hands-on activities in all training modules. The instruction will exceed MSHA requirements. The resources available on Montana Tech’s campus will be utilized to strengthen the training program providing the mining industry with a world class mine health and safety training program.

Feb 1, 2023

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train, the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71 percent — as confirmed by real operational data from the Antapaccay Mine in Peru. It was the first plant worldwide to use gearless drives for both applications.The gearless principleThe principal idea behind a gearless drive system is to reduce the number of components and diversity of parts, especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material.In order to apply this principle of simplification, the components of a conventional drive system are examined. They consist of:• Driven equipment (mill, conveyor, slurry pump).• Components altering the rated speed (gearboxes, girth gear/pinion).• The electric motor.• Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage.• Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation.• The electrical supply system (cables, switchgear, transformers, protection equipment)."

Jan 1, 2015

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By J. Morris, R. Sellaro

Petro-diesel is a common collector for coal flotation, but the partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO contents in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DROs. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAH contents were measured in the waters associated with the concentrate and tailings streams. The results show that concentrate waters consistently had higher amounts of DROs than tailing waters. Moreover, the DRO contents in both streams generally increased with increasing diesel dosage. In line with preliminary research, DROs appeared to be limited to the WSF, and PAHs tended to partition proportionately with DROs. Under typical operating conditions, it appears that residual DROs should not present an environmental concern, but conditions should be avoided that allow significant overdosing of diesel.

Jan 1, 2014

By Alphonce Wikedzi, Mussa D. Budeba, Samwel V. Manyele, Sospeter P. Maganga

The present study provides an overview of the challenges and opportunities in processing complex gold-copper ores. The systematic literature review was conducted using Scopus database and seven-step methodological approach. The study indicates that the major challenges in processing complex gold-copper ores through the conventional cyanidation method include (1) increase in cyanide consumption; (2) increase in cyanide destruction cost; (3) low gold recovery; (4) decrease in adsorption efficiency; (5) decrease in electrowinning efficiency, and (6) difficulties in the measurement of free cyanide concentration in the leaching system. Moreover, the study indicates that several methods have been developed and some have been implemented in the mining industry for processing complex gold-copper ores. This includes ore segregation, pre-aeration, pre-treatment methods (e.g., ammonia), alternative lixiviants (e.g., thiosulfate, thiocyanate, glycine), cyanide destruction methods, and cyanide and copper recovery technologies. The study concluded that using lixiviant mixtures (e.g., cyanide-glycine), pre-treatment with environmentally friendly reagents (e.g., glycine) and the integrated membrane-based process (SuCy process) are new directions in processing complex gold-copper ores. However, more investigations are required to advance these processes to a commercial scale.

Sep 30, 2023

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994