Search Documents

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By John G. Groppo, James C. Hower, Cortland F. Eble, Rick Q. Honaker, Alireza Valian, Stephen F. Greb

Coal and coal combustion byproducts are potential candidates for alternative resources of REEs (rare earth elements). The Illinois Basin is a major coal-producing district in the USA, but little work is available on speciation of REEs in the basin’s coals. In this study, a total number of 382 samples from known locations in the Illinois Basin coal beds were acquired, analyzed for their REE contents, and investigated for any spatial trends or chemical correlations. This study includes Springfield, Herrin, and Baker coal beds—the most heavily mined coals in the basin. An average coal ash from the basin contains 320 ppm REE, with Baker being the highest (407 ppm on average). However, the distribution of REEs in the coal beds was laterally and vertically heterogeneous. A number of trends were found in the REE variations. The most important trend was the relationships of the REE concentrations and fractionations with the distance from the syndepositional sandstones. The total REE concentrations were higher in the proximity of the sandstones, likely due to the increased deposition of detrital material. This increase was the most significant in Springfield coal (90%) and least in Baker (6%). Those coal samples from the Springfield and Herrin coal beds distal from the syndepositional sandstones had a heavy to light REE ratio (H/L ratio) of 0.40 on average, whereas in proximal locations, the ratio was dropped to an average of 0.30. This trend was not significant in the Baker coal bed. In general, higher mineral matter in the coals was associated with higher REEs. In coal preparation plants, refuse rocks can have up to 360 ppmREE. However, the ashes of the cleanest coals had higher REE levels. Such ashes also have a higher ratio of heavy to light REEs. The highest REE concentrations were found in the claystones and the shales associated with the coal beds. Since the naturally occurring calcite, quartz, and pyrite samples were depleted in REEs, an association of REEs with the clay minerals can be suggested.

Jul 20, 2020

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By Sufi Md Gulzar, L B. Roy

Rock engineering tasks like tunnelling, dam and building construction, and rock slope stability rely heavily on properly estimating the rock’s uniaxial compressive strength (UCS), a crucial rock geomechanical characteristic. As high-quality specimen are not always possible, scientists often estimate UCS indirectly. The primary objective of this paper is to assess the efficacy of long short-term memory (LSTM), K-nearest neighbour (KNN), a combination of particle swarm optimisation (PSO) with an artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) to estimate the UCS of sandstones from Jharia, Dhanbad, India. Point load index (PLI), porosity (n), P-wave velocity (Vp), density (ρ), and moisture content (%) are the parameters used for the present study. Finally, a comparison was made between the various prediction algorithms outputs. The findings of the study validated the effectiveness of computational intelligence methods in forecasting UCS compared to other models used in this paper. The KNN achieves overall the best results, with an R2 of 0.95 for training, 0.94 for testing, and an RMSE of 0.03 for training and 0.05 for testing.

Nov 23, 2023

By Ebrahim Ghasemi, Mohammad Hossein Kadkhodaei, Mosareza Jalilian

Entry-type mining methods, such as cut and fill method, play a significant role in underground mining, and they are still suitable methods for extracting deposits with irregular shapes and with weak host rocks. In these mining methods, the stability of the open spans is important for improving worker safety and increasing ore recovery. This study focuses on the application of six data mining classification methods, namely multinomial logistic regression (MLR), classification and regression trees (CART), logistic model tree (LMT), decision tree (J48), multivariate adaptive regression spline (MARS), and gene expression programming (GEP), in order to develop predictive models for stability assessment of underground entry-type excavations. For this purpose, a database containing 399 case histories of entry-type excavations from seven Canada underground mines was used. These models predict the stability status of entry-type excavations based on two input parameters, dimensions of the span and rock mass rating (RMR). The performance of developed models was evaluated using six performance metrics namely accuracy (ACC), sensitivity (SE), precision (PR), Matthew’s correlation coefficient (MCC), area under the receiver operating characteristic (ROC) curve (AUC), and performance index (PI). The results showed that all developed models can be used to predict the excavation stability, but the comparison of models indicated that the J48 model provides the highest performance with ACC = 0.900, SE = 0.869, PR = 0.922, MCC = 0.835, AUC = 0.891, and PI = 4.417. Thus, the proposed J48 model can be applied to identify the susceptibility of span instability in the entry-type mining, and if instability has been predicted, the necessary measures, including the use of suitable support systems, can be considered to reduce the casualties resulting from span instability.

Feb 26, 2024

By Antonio Rivera

On Nov. 13, 1985, Colombia's Ruiz volcano erupted, killing an estimated 25,000 people and burying several villages. Damages were estimated to be about $US300 million. The following is an account by SME member Antonio Rivera of the volcanic activity that led to the eruption. His account also includes a description of the geography and some geology of the affected area. Mining operations in the area were mostly unaffected, although some operations were forced to close until the roads leading to them could be repaired. Introduction The Ruiz volcano is located on the Central Cordillera of Colombia about 28 km (17 miles) southeast of Manizales, the capital of the state of Caldas. Ruiz is one of nine volcanoes that form a complex volcanic chain within the middle portion of the Central Cordillera. The Cordillera has 30 other volcanoes in the southern part of Colombia. Ruiz volcano Ruiz's elevation is 5200 m (17,060 ft). It is covered by an ice cap estimated to be 20 m (66 ft) thick at its summit, an area that covers 17 km2 (6.5 sq miles). Drainage is composed of several rivers that flow into the Magdalena River on the east and Cauca River on the west. The rivers flowing to the east are Guali, Azufrado, Lagunillas, and Recio. The rivers that flow to the west are Claro, Molinos, and Chinchina. There is a road from Manizales to El Refugio, a ski area located on the northeast flank of the volcano at 4800 m (15,750 ft) in elevation. The Ruiz volcanic complex was built in two stages. The first is a shield type of volcano (mainly lavas) formed about a million years ago. The second is a younger stratovolcano overlaying the ancient one. It consists of lavas and pyroclastics and was built over the past 500,000 years. Twenty-four eruptions of Ruiz are known to have occurred during the last 14,000 years. Its products mainly consist of lava flows, pyroclastic flows, mudflows (lahars), and directed lateral explosions. Historic eruptive record 1595 - Debris avalanche, blast, pyroclastic flows, mudflows, ash flows, and ash fall. 1828-1829 - Ashes (phreatic). 1831-1833 - Gas emissions and ashes. 1845 - Mudflows and pyroclastic flows. 1985 - Sept. 11- Fumarolic activity, phreatic eruption, ash fall, and small mudflows. 1985 - Nov. 13 - Ash and pyroclastic fall, major destructive mudflows (magmato-phreatic eruption). From 1845 through 1984, Ruiz volcano always had a slight fumarolic activity. It was restricted to the crater area. In November and December 1984, the fumarolic activity increased and the first ash emission and vapor-sulfur formation started. Small local earthquakes accompanied these volcanic activities. The volcano had a small erup¬tion on Sept. 11, 1985. It was manifested by phreatic explosions that ejected fragments of the vent and formed ash deposits 25 mm (1 in.) thick around an area 2.5 km (1.5 miles) from the crater. Fine material was blown by the wind and reached Manizales and neighboring areas, producing a small layer of ash up to 10 mm (0.4 in.) thick.

Jan 2, 1986

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

By Thomas E. Ban

During recent years fuel consuming industries of the United States have been caught between environmental restrictions and the uncertainty of obtaining an inexpensive fuel. With the advent of the National Energy Act of 1978 there has been added impetus to switch from gas and oil to coal. For industrial furnaces and boilers that were designed to bum coal, returning to an available compliance coal might be feasible. However, furnaces and boilers designed for gas or oil cannot reasonably be converted to coal unless the coal is initially gasified. All cases, nevertheless, depend upon the availability of an adequate structured coal of a compliance composition, a challenge to the coal mining industry. The foregoing problems have contributed to the current energy-coal crisis of today's economies. It therefore would be worthwhile to capitalize on previous experiences of the mineral processing industry.

Jan 1, 1979

By David Morrison

"The history of the mining industry is littered with in-pit crushing and conveying (IPCC), which should not be confused with the International Protocol for Carbon Capture, projects that failed. The failure is not the technical one of “did it achieve the desired tonnage rate for a longish test period” but, rather, the far more important one of “did it provide return on the investment in the manner that was promised?” While quite a few can claim the former, very few system installations can claim the latter.The reasons for the many failures are numerous, but they are all characterized by a combination of an element of engineering optimism in any, or all of the production rates, the productivity, or the operating and maintenance costs and in predicting the continuity of operating conditions. In these days of big data, propagating such a situation is rapidly becoming unforgivable.In this article, the three most common scenarios put to the corporate board for approval, and the logic as to why they were selected, are examined (with the irony included intentionally).• Fully mobile crusher, fed by a shovel and conveyed out of the pit to a waste dump / process plant.• Semimobile crusher (much more expensive than a fixed crushing station but which apparently allows trucks to short haul inside the pit and improve productivity), which moves when the face moves.• Relocatable crusher (more expensive than a fixed crushing station but which gets relocated at great expense after all the fixed infrastructure impeding relocation is demolished) fed by trucks that don’t leave the pit mostly.This paper will also consider the truth about their operational performance and associate costs."

Dec 1, 2016

By Roy H. Paddon

This paper describes the 6, 000 tpd, three stage haulage system at the Ozark Lead Company's mine in southeastern Missouri. It details the methods and problems pertinent to the loading, hauling, sorting, crushing, storing and hoisting of waste rock and ores obtained from underground development headings and production areas. The Ozark Lead Company is a wholly owned subsidiary of the Kennecott Copper Corporation. Its mine is located nine miles south of Bunker in Reynolds County at the south end of the "New Lead Belt" mining district. Development started in May, 1964, by drilling a seven foot diameter (six foot cased), 1, 250 foot development-ventilation shaft. Drifting began in August, 1965, to obtain a bulk ore sample, to test ore continuity, and to drive two mine levels while the pre-grouted production shaft was being sunk. Over 7, 900 feet of 12 by 24 foot drifting was done from this small shaft. In March, 1966, a 20 foot diameter, three compartment, concrete lined production shaft was collared. It intersected existing development headings at a depth of 1, 195 feet in April, 1967, and was completed along with a concentrator and other facilities in June, 1968. Mine production began that month, with 5, 000 tpd reached in 1970.\

Jan 1, 1971

By Timothy D. Arnold

Barrick Gold’s Bullfrog underground mine, near Beatty, NV, was established as an after-thought to the main open pit. As open pit ore dwindles, the underground mining became increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines. Today, there is a move towards underground mining in the United States. There are inherent problems in starting and operating underground mines in the shadow of any open-pit operation. Several attempts were made at the Bullfrog Mine for productive increases. Some were successful, while others were not.

Jan 1, 1996

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007

By R. Switalski, M. Schafer, R. Pintabona, M. Kritzer, B. Lukajic, S. Janosko

Methane gas caused an eight-month shutdown of mining operations at the Mill Creek, Phase 3, Tunnel. The gas-related shutdown occurred as the tunnel was advanced to an approximate distance of 2,700 feet, which constitutes approximately18% of the total tunnel length. The construction of an emergency ventilation shaft, a comprehensive program of de-gassing wells and an expanded gas monitoring system were used to mitigate the gas condition. When complete, this tunnel will be utilized to convey and store combined storm and sanitary sewage collected from a portion of Cleveland, Ohio and ten suburbs. This paper will provide an overview of gas related remedial measures and explain how these measures were integrated into the project to ensure safe tunneling conditions.

Jan 1, 2007

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By Marianne Snedeker

In January we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. At the same time we hired an outside firm, READEX Inc., of St. Paul, MN, to send the same questionnaire to a sampling of about 1000 US members, selected on an nth name basis, so that we could have some preliminary numbers for the Annual Meeting in February. READEX sent us the final results of its survey in March. At that time, 525 responses of the 992 surveys sent out had been returned, for a 52.9% response, an extraordinarily high return for a low-key (no incentive for return) random sampling. On May 7, we cut off on tabulating returns from the magazine so that we could report the results to you in this issue. At that time, we had 594 questionnaires returned. Our 594 and READEX's 525 (we have assumed that relatively few people returned both), represent a 1119 return, about 3.5% of the approximately 32,000 who received the January issue of ME. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded, told us something positive-you look at or read the magazine. Of the 1119 respondents, 1068 or 95.4% indicated that they had read or looked through the November and/or December issues. Those of you who refer to the magazine once are 466 or 42.6%. Those of you who refer to the magazine two or three times are 559 or 51.1%. Those of you who refer to the magazine four or more times are 68 or 6.2%. How much time do you spend reading the magazine? Of those responding to this question: 186 spent up to 1/2 hr 16.6% 590 spent up to 1 hr 52.7% 292 spent 1-2 hr 26.1% 51 spent more than 2 hr 4.6% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 764 or 69.4%, clip your magazine for further reference. Also, many of you, 513 or 64.2%, do not pass your copy on to another reader, indicating perhaps that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 2 people - 159 - 20.0% 3-5 people - 95 - 11.9% 5 or more - 31 - 3.9% Answers to what portions of the magazine you find useful indicated that the top three were Industry News, feature articles, and Technical Papers; see Table 1. The "other" category included advertising-display, classified, and employment-Coming Events, product information, Washington Survey, new books, the reader service card, and Engineering Fundamentals. Of those responding, 797 or 75.3% indicated a preference for dual notation of SI (metric) with English units; 228 or 21.5% preferred all SI units; while 34 or 3.2% preferred SI with dual notation of other metric units. Based on the preliminary numbers reported by READEX for this question, the MINING ENGINEERING Committee in February voted to return to a policy of dual notation. This decision has been implemented. We asked for your appraisal of the technical level of the magazine. Of those responding, 78 or 7.4% indicated it is too technical, 147 or 13.8% indicated it is not technical enough, and 836 or 78.8% judged it to have the correct tech¬nical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 32 said no, but an overwhelming 97% (1024) said yes. Of the specific topics, 785 like history, 558 political or socioeconomic articles, 440 career development, and 373 human interest. Other topics suggested included new disciplines, mineral resources of the world by

Jan 6, 1982