Search Documents

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008

By Stanisław Prusek, CHONG WEI, Huawei Xu, Jun Wang, Andrzej Walentek, Artur Dyczko, Derek B. Apel

The excavation-induced stresses transferred from the panels or pillars in upper coal seams play a key role in the occurrence of rockbursts in driving roadways during close-distance coal seam mining, which has become a common problem and threat to many underground mines. The authors established a 3D finite-difference numerical model via FLAC3D software using the closedistance coal seam mining conditions in the Zofiówka Mine as a case example to reveal the rockburst mechanism in such conditions. The excavation-induced vertical stresses are analyzed, which provides a basis to build a conceptual model to explain the possible source mechanism of the rockburst under such conditions. Nine typical rockburst indicators considering different contributing factors are then selected as the evaluation criteria to assess rockburst potential in the study site. The results suggest that the superposition of multiple excavation-induced stresses of the main drift and tailgate provides an environment for stress concentration and energy accumulation. The side abutment stress induced by mining in the upper coal seam has a “strengthening” effect to the rockburst occurrence. The great deviatoric stress induced by complex excavating situations is another important exterior cause. A strict calibration procedure should be implemented before using indicators to predict rockburst potential. A methodology was proposed to estimate the location and magnitude of rockbursts combined with numerical modeling, laboratory tests, and feedbacks from the field. The study could provide some references and guidelines for preventing and mitigating rockbursts in underground mines under similar engineering conditions.

Aug 26, 2021

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.

bauma 2004 will feature a couple of firsts for one of the world’s largest construction and building materials machinery exhibitions. The event is scheduled for March 29 through April 4 of next year at the New Munich Trade Fair Center in Munich, Germany. For the first time, bauma will feature an exhibition area dedicated to mining equipment and technology. Also for the first time, the Commonwealth of Independent States (CIS) will be a partner region of bauma.

Jan 1, 2003

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By K. H. Boss

In modern iron pelletizing plants fuel consumption has been optimized to such an extent that only minor savings can be expected in the future. Inspite of this fact, different process parameters were studied with a mathematical model and firing tests. The influence on fuel consumption and productivity was established. Furthermore, the adoption of simplified firing patterns was investigated, in particular for coal firing. In view of high costs of oil and natural gas, only substitution of these fuels by coal can substantially reduce production costs. In existing plants partial replacement of oil and gas can be achieved by addition of coal to the iron ore feed and by firing the pellets with pulverized coal. Two systems have been developed for the Lurgi- Dravo travelling grate process which enables coal to completely replace oil or gas. This paper describes in the first part the potentials for fuel savings available in the Lurgi-Dravo process. In the second part, different techniques for the use of coal as fuel in iron or pelletizing plants and in particular the recently developed Lurgi Multistage Coal Injection and Combustion Process (LMC) are discussed. Combined with the LMC process, a wide variety of iron ores and coals - also with high ash contents - can be used in the Lurgi-Dravo travelling grate process.

Jan 1, 1983

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By R. F. Balazik

By March 2001, shrinking global markets, reduced consumer spending and declines in domestic manufacturing and industrial output ended the longest economic expansion in US history and pushed the nation’s economy into its first recession in a decade. Aggravated by the terrorist attacks of Sept. 11, the recession led to large reductions in the domestic production of processed mineral materials. Some of the most significant production declines in the US metals industry were registered by aluminum, copper and steel producers. They faced strong foreign competition, higher energy costs and lower prices for their products. However, homebuilding and other domestic construction sectors — major users of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above previous year levels. A strong US dollar continued to weaken the competitive stance of US metal and nonmetallic mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2002

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

With the advent of the environmental "green" movement of the 1960s, eventually leading to Earth Day 1970, Congress responded by passage of the National Environmental Policy Act (NEPA), 1970. NEPA gave impetus to a flood of federal acts and laws in the subsequent three decades. Many of those protecting man's environment, health, and well-being also affect mining. For purposes of this chapter, a current mineral law summarization lends itself to a division into two parts: viz., Part I, General Mining Law, and Part II, Enviromining Law. The word enviromining has been coined by the author and is defined and used herein as those federal and state statutes and regulations that were created to provide protection and preservation of man's environment, health, safety, and welfare, and they have particular application to and affect on mining activities. They are listed and treated under Enviromining Laws in Part II. Mining, as a basic industry to provide the essential minerals for mankind's necessities and well-being, truly reflects the mining industry's slogan, "If it can't be grown, it must be mined." Without the basic minerals and rocks won from the earth by mining and mineral processing for their valuable physical properties or chemical constituents, man would soon be forced to revert to the cave-dwelling age. Unfortunately, for man to survive in the "manner of life to which he has become accustomed," he is caught between the demands of cleaning up his deteriorating environment and a continued supply of his basic requirements and amenities for daily living supplied by mining of the earth's minerals. He must have "clean living" at the same time with "good living;" neither is expendable. A very high pricetag accompanies this essential and critical choice which must be paid by society. The United States is internationally recognized as the world leader in environmental matters. Many countries are following suit, principally the other Anglo nations. Because US law is founded and based on English law, on occasion, Anglo-American law is referred to and cited as authority in litigation anywhere in the Anglo-American world of jurisprudence. For this reason, and because mining and the industry is international in nature and operations, some British Commonwealth cases will appear in various topics. If the case is of interest to the reader, further inquiry at a law library may be made through use of the case's style and citation given. "Style" refers to the name of the litigating parties. "Citation" refers to the law publication in which the case and decision may be found, as well as the jurisdiction and court of decision. Citation of cases from the United States and British Commonwealth nations is explained under Case Citation Explanation. Space and time limit exhaustive treatment of subjects and covering all geographic and jurisdictional areas. This chapter is intended as a broad outline and is based on the author's master's thesis at the University of Missouri-Rolla, 1992. The following Case Citation Explanation provides guidance on formatting of citations.

Jan 1, 1994

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By Joseph J. Feiler

Fires in underground coal mines are persistent problems anywhere in the world that coal is mined. Coal fires pose safety and health hazards in the form of mine subsidence, loss of energy reserves, destruction of property and surface improvements, and air pollution. In 1995, the US Bureau of Mines (US-BM), in cooperation with the Colorado Division of Minerals and Geology (CDMG),entered into a contract with Goodson & Associates Inc. (GAI) to design and field test the effectiveness of a new foamed grout technology called ThermoCell. GAI is a Lakewood, CO geotechnical and mining reclamation engineering firm. The company developed ThermoCell to control and extinguish underground coal fires. The viability of the special grout and the technology of application were established during a full-scale field demonstration at the abandoned IHI Coal Mine fire, near Rifle, CO. Following acquisition of additional funding by CDMG in 1999, Goodson returned to the site in April to continue the grouting to fully extinguish the IHI fire.

Jan 1, 2000

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005