Search Documents

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By A. Nieto

Rare earth elements (REEs) are crucial to green technology such as hybrid-electric vehicles, wind turbines and fluorescent light bulbs. As of 2011, China dominates the global production of REEs and is reducing its export quotas. To predict the supply of rare earths in the United States based on future supply scenarios, a web-based database and geographic visualization tool was built. Five case scenarios with varying levels of REE demand were created by varying several economic conditions including (1) international trade policy, (2) greenhouse gas regulations, (3) environmental mining regulations and (4) tech applicability ratio of REEs. The most likely scenario, which is based on current international demand levels, indicates the importance of expediting the development of extractive operations of current REE resources within the United States. The results of the different case scenarios are supported by using dynamic geographic maps indicating the location of rare earth ore (REO) resources.

Jan 1, 2012

By William Gleason

"Government support for Canada’s mineral industry was on full display during the Prospectors & Developers Association of Canada (PDAC) conference in Toronto, ON, Canada on March 3-6. First, there was the announcement of the five-year extension of Canada’s Mineral Exploration Tax Credit (METC), the first multi-year extension of the METC since its inception in 2000. Canada’s Minister of Natural Resources, Amarjeet Sohi, added to that support when he spoke at the opening keynote session and announced the Canadian Minerals and Metals Plan (CMMP), a plan that aims to map out the future of the industry in Canada. Finally, the support for the mining industry was buttoned up with a visit to the conference by Canadian Prime Minister Justin Trudeau.More than 25,000 people from 135 countries attended the annual conference that features a robust trade floor, technical sessions and an investors’ exchange that aims to put mining companies in touch with potential investors. Mining companies and ambassadors from nations around the world are given the opportunity to present to small audiences throughout the conference and this year PDAC was able to sway the Prime Minister to speak on its behalf.Trudeau sat down with PDAC President Glenn Mullan on March 5 to talk about the METC extension and a host of other issues important to the Canadian and global mining industry, giving the home country a bit of a profile advantage when it came to making a pitch to investors.Trudeau entered the week of the conference in the midst of the most serious political scandal of his career and was defending himself against accusations of political interference with the top prosecutor in the land over a criminal case involving one of Canada’s largest companies, SNC-Lavalin. During the question-and-answer session at the Metro Toronto Convention Center, Trudeau seemed more than happy to keep to the discussion about mining. He spoke favorably about the industry during the half hour conversation and praised the industry for its work with Indigenous people as well as its efforts to advance technology and innovation. He made a case that Canada is a safe and reliable place for investment in the minerals sector.“We are at a time of change right now, of transformation with new technologies and global supply chains, and everyone is trying to adjust to the new realities that have accelerated so much these past years,” Trudeau said. “What we are trying to do as a country and what you have done as an industry is to try to look at where things are going – go to where the puck is going to be, not where it is. You, as an industry, know that investments in innovation, research, science — investment in technology and partnerships with Indigenous communities are all things that are going to give you opportunities to be competitive in the coming years.”"

Apr 1, 2019

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By S. K. Palm

The commercial life of a mineral product can be long, but like hitech electronic and software products that soar in sales one day to become obsolete and forgotten a few months or years, mineral products have a life cycle. They are invented, commercialized and eventually decline and disappear from commerce. Diatomite and perlite are produced from mined minerals, but almost none of the products in these industries spring from the earth in finished form. Straight calcined diatomite was invented over 100 years ago and flux calcined diatomite just a few years later. The expansion properties of perlite were discovered and first exploited about 75 years ago. Some applications for diatomite have disappeared or currently face competition from newer products. Dry cleaning was once the second-largest application for diatomite but disappeared over 30 years ago. Both the beer and wine filtration markets for diatomite face increased competition from membrane filters. A pipeline of new, proprietary products is critical to the future of the industry.

Mar 2, 2022

The 30th annual American Mining Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Star Pass Resort, Tucson, AZ on Saturday, Dec. 1, 2012. Each year, one living inductee, two recipients of Medals of Merit and up to five honorees from mining history are chosen by the MFSW for their outstanding contributions to the mining industry. Gregory H. Boyce will be the guest of honor, featured speaker and inductee into the American Mining Hall of Fame. Boyce, chairman and chief executive office of Peabody Energy, is being honored for his leadership in the coal industry.

Jan 1, 2012

By C. Meyer, J. J. Eidel

C. W. Hunt I wish to register strong disagreement with the choices of drilling sites chosen by the Continental Scientific Drilling Committee, while endorsing the stated objectives. Of special significance is the lack of any site involving the metals most needed today in the US, while 9 to 13 km of drilling are allocated to gold and silver districts and 11 to 17 km to base metal (mainly copper) districts. Why is nothing proposed for platinum group or chromite? Is this because the committee did not know of such a site? If so, I offer such a site in California (see Fig. 1). The mineralization shown in Table 1 occurs in a large peridotite body in western Tehama County, CA. Petrography has demonstrated unequivocal evidence of migrated PGE deposited in peridotite and chromite of hypabyssal nature. Active diapirism (due probably to serpentine buoyancy) above a reactivated mantle to surface conduit marks the position of the conduit. Young explosion breccia cemented loosely by volcanic glass and tuff demonstrates the significance of the conduit as the prime source of the various emissions. Deep drilling could result in major metals discoveries as well as shedding light on the grand questions of platinum group mineralization. What role water has played in this occurrence is not yet certain; but chlorine and asphaltite have been detected in and adjacent to native PGM, suggesting a major role for water. The explosion breccia suggests that this excellent site could overlie entrapped geothermal steam.

Jan 6, 1987

By Richard B. Stein

Section 25 has been assembled to give the geological, mining, or metallurgical engineer an overview of some of the important downstream operations that typically follow mining activities. This subject is obviously too broad and complex to be covered in detail within this Handbook. However, the engineer will be interested to learn about the basic fundamentals, and especially how they might affect the economics of the total project from prospecting and mining through to metals recovery and marketing. In this way, it is hoped that the engineer will have a better overall appreciation for the technical and commercial prospects of a mining and metal-producing project.

Jan 1, 2008

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By S. C. Carniglia

Bayer-process alumina hydrate becomes in turn the source of a host of special products in addition to the calcines that feed aluminum reduction cells. Though relatively smaller in tonnage, specialty aluminas serve important industrial markets in an exciting and growing variety. Production methods and applications are discussed for: (1) trihydrate as flame retardant in organic materials; (2) high-surface-area transition aluminas as desiccants and scavengers, catalysts and substrates; (3) calcines for industrial ceramics, refractories, and abrasives; and (4) tabular alumina for refractories, bed supports and other uses.

Jan 1, 1977

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By F. F. Roberto

Many techniques that are used to characterize and monitor microbial populations associated with sulfide mineral bioleaching require the cultivation of the organisms on solid or liquid media. Chemolithotrophic species, such as Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans, or thermophilic chemolithotrophs, such as Acidianus brierleyi and Sulfolobus solfataricus can grow quite slowly, requiring weeks to complete efforts to identify and quantify these microbes associated with bioleach samples. Real-time PCR (polymerase chain reaction) assays in which DNA targets are amplified in the presence of fluorescent oligonucleotide primers, allowing the monitoring and quantification of the amplification reactions as they progress, provide a means of rapidly detecting the presence of microbial species of interest, and their relative abundance in a sample. This presentation will describe the design and use of such assays to monitor acidophilic microbes in the environment and in bioleaching operations. These assays provide results within 2-3 hours, and can detect less than 100 individual microbial cells.

Jan 1, 2009

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo&apos; where svo&apos; is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By S. Borner Schweizer

An overview over SAM’s approach to assess corporate sustainability performance illustrates how sustainability challenges are linked to trends, assessment criteria and finally company performance. This process is exemplified with some general and industry specific criteria. Lastly, results of the Dow Jones Sustainability Assessment 2004 show a considerable gap between leading and average companies. Best practice examples demonstrate how lagging companies could improve their sustainability performance.

Jan 1, 2005

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By Eric Eisold

The Wachovia Headquarters and Arts and Cultural Campus project in Charlotte, NC includes a 1.5 million square foot, 48-story office tower, two museums, an Afro-American cultural center and a 1,200 seat theater for the performing arts. Public access to the Cultural Campus is through two pedestrian tunnels constructed under city streets connecting to parking garages. The 5.7 m wide by 4.7 m high mined tunnels were procured through a design-build contract. The tunnels were designed as initial/final shotcrete linings with a sprayed water barrier sandwiched between layers of shotcrete. In addition, the mix design was supplemented with a cementitious admixture to develop internal water resistant properties in the shotcrete.

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By M. Ahrens, J. Gonser

Gearless mill drives are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as their advantages compared to other drive solutions. Due to the variable speed operation the grinding process can be optimized for ores with varying grinding properties. This leads to significant optimization potential for the plant design as well as for its operation. Furthermore, energy and cost savings due to optimized operation, high system efficiency and high system availability are shown.

Jan 1, 2007