Search Documents

The development of technologies to improve mining and mineral processing is an ongoing process. These new technologies are the result of the industry’s drive to lower costs and improve productivity. Many technical conferences allow mining industry professionals to learn about these new technologies and possibly implement them in their own operations. In early November 2005, The 14th symposium on Mine Planning and Equipment Selection (MPES) was held in Banff, Alberta. It was jointly held with the Fifth International Conference on Computer Applications in the Minerals Industries (CAMI).

Jan 1, 2006

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

Nuclear power currently produces about 20% of the electricity in the US, with 104 nuclear power plants located in 31 states. The commercial US nuclear industry contributes over $4 billion annually to US workers in salaries and wages. 25,000 new jobs need to be filled in the next 5 years. There are over 30 new power plants under consideration by US utilities. The operating reactors use uranium oxide fuel enriched to about 4% U235 and fission is the process used to generate heat to form steam to drive the turbine generators. Nuclear energy is an important element in the US generation portfolio and represents the largest producer of nearly emission-free electricity. Most, if not all, of the operating plants will secure an extended 20 years of operation or more. The last plant constructed was ordered in 1978. New smaller, modular reactors are under design to provide less expensive, expandable generation options.

Jan 1, 2011

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By V. L. Andrade, K. L. C. Goncalves, N. A. Santos

This paper describes results obtained in a test program performed with new equipment, called Mini Pilot Plant, manufactured by Canadian Process Technologies. This equipment was acquired by CVRD aiming at testing flotation circuits, in a continuous closed configuration, with samples obtained from drill cores. Success of this goal would allow CVRD to establish the metallurgical performance of mineral deposits with more confidence in comparison to Locked Cycle Tests (LCT). This paper discusses the importance of assessing the ore variability and compares results obtained in LCTs and Mini Pilot Plant. Results suggest that more reliable data is obtained in MPP test.

Jan 1, 2002

By Roger G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of Project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the Project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mecha¬nics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1983

By Amy McBrayer, Andrea Brickey

The paper discusses the mine planning methods used in the Powder River Basin (PRB), highlighting the differences from open-pit metal mines. It emphasizes the need for agile mine operations due to changing commodity markets and the challenges faced by the coal industry, such as volatile prices and reduced engineering manpower. The study includes a survey of mine engineers to document current practices and identify potential improvements.

Sep 1, 2023

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

By E. Rubenstein, V. Gangrade, K. V. Raj, M. L. Harris

Underground stone mine ventilation is characterized by large openings with low resistances. These mines primarily face three challenges: moving adequate volumes of air, controlling and directing the airflow, and planning ventilation systems that work well with production requirements. Given these challenges, this paper examines the data collected by the Mine Safety and Health Administration (MSHA) to determine the extent to which respirable crystalline silica (RCS) and diesel particulate matter (DPM) are an issue in underground stone mines. Out of 522 sampled mines, there were 108 personal samples exceeding the RCS Permissible Exposure Limit (PEL) during 2000–2020. DPM were more prevalent than RCS in these mines with 382 personal samples exceeding the DPM PEL out of the 929 mines sampled during 2002–2020. Dilution of DPM is usually the defining parameter for design of mine ventilation systems in largeopening underground stone mines. With this knowledge, focused attention can be directed to these mines so that appropriate prevention and mitigation techniques can be utilized to prevent stone miners’ exposure to RCS and DPM and subsequent respiratory diseases.

Mar 2, 2022

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

By P. Koh

A novel approach incorporating computational fluid dynamics (CFD) and flotation modelling has been used for investigating flotation cell designs. CFD modelling has increasingly been employed to enhance understanding of the cell hydrodynamics in mineral and coal flotation. Opportunities for improving the flotation cell performance can be identify by modelling. The CFD-flotation model from CSIRO incorporates cell hydrodynamics that affect particle-bubble interactions. Information from the model includes velocities, turbulent dissipation rates, gas hold-up, particle-bubble attachment and detachment rates. The attachment and detachment rates have been found to be effective measures of cell performance for cell design.

Jan 1, 2011

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By A. C. T. Bigg, Y. Kocak, N. K. Bodur

The Gumuskoy silver mine, owned by the Etibank, in the province of Kutahya, Turkey, has been operating since 1987 with primary, secondary and tertiary crushers, and two parallel single stage ball mill circuits. Continuing problems with crushing and feeding of the ore to the ball mills, because of the moisture retaining and sticky nature of the ore, prompted an investigation into the possibility of converting the grinding circuit to an autogenous or semiautogenous grinding circuit. This would remove the bottleneck associated with the secondary and tertiary crushing. At the same time the target feedrate is to be raised from 140 t/h to 175 t/h. This paper demonstrates the response of five ore types, and blends of ore types in an onsite pilot plant test program, and also suggests how the variations can be handled in a SAG mill/ball mill circuit incorporating just one of the present ball mills.

Jan 1, 2000

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

By Kenneth J. Hartman

Introduction The term kaolin is derived from kauling, a Chinese word meaning high ridge. This was the name of a hill in China where kaolin was first mined several hundred years ago (Murray, 1976). Other common names used for kaolin include clay and China Clay. Clay technically has a broader meaning and could refer to bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin. But it could also be due to a significant historical use in ceramic applications. The terms kaolin and clay will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's wide-spread industrial usages center on kaolinite's physical features of good color, low viscosity, and inertness. Kaolin is described as a hydrous aluminum silicate with an approximate composition of 2H2O • A12O3 . 2SiO2. A new version of the product is calcined clay with modified hydration content. It is gaining widespread use. Components of any particular kaolin, in addition to alumina and silica, are viewed as impurities. The more values deposits and, hence, higher priced kaolin products are those of the highest purity. Kaolin is the most widely used mineral in paper manufacturing throughout the world. Key production centers are located in England and the US. Most of the Tatter's production is located in Georgia. The key markets for Georgia kaolin are paper markets - both paper coating and paper filling. These paper markets extend throughout the world, not just to domestic markets. In fact, export markets are second in size only to domestic paper markets for Georgia's producers of kaolin. Just as the paper markets are important for kaolin producers, kaolin is an important raw material for papermakers. Compared to the other three major pigments - titanium dioxide, calcium carbonate, and talc - kaolin's 1984 tonnage for papermaking represented 85% of the total. Even though titanium dioxide's unit value is much higher, kaolin's estimated total 1984 value still represented 51% of total dollars spent by papermakers for the four pigments. Kaolin grades- are briefly defined using particle size and brightness as principal means of classification. Likewise, grades of papers using kaolin are defined using the American Paper Institute's guidelines. From these definitions, associated kaolin grades used in particular grades of paper are reviewed. Special emphasis is placed on how qualities desired in certain papers are achieved through the use of specialized kaolin grades. World kaolin production World production statistics (Coope, 1979; Table 1) demonstrate that kaolin is produced in many areas of the world. About 60% of production is centered in the US and England (Fig. 1). Deleting Eastern Europe's produc-

Jan 4, 1987

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By C. R. Landis

The Wyoming bentonite industry continued its run of stable, if not strong, growth in its complex markets. Growth at the macroscale was fueled by a strong domestic economy, the weakening of the U.S. dollar in the global market and strong worldwide global demand. Challenges to the benchmark of the industry were rapid and saw ongoing increases in raw material costs(pallets, bags and additives), higher energy costs and higher overall transportation costs for all modes of movement. Exports continued to be assisted by dollar depreciation (5 percent to 10 percent) from January 2004to January 2005. This depreciation followed the significant weakening of 2003. And it was most favorable during the pullback in fuel and shipping rates in the second half of the year.

Jan 1, 2005

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Chen-Luh Lin, Jan D. Miller

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of centimeter size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of millimeter size. Based on Micro-XCT, it was expected that 85 percent of copper for sample A could be recovered at 65 percent of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual-energy X-ray radiography was used as a basis for sorting. Pilot-scale X-ray sorting of sample A (10 × 1 cm) showed 31 percent rejection of a 0.08 percent Cu gangue product with a corresponding recovery of 90 percent copper.