Search Documents

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By Dziurzyn&apos, W. ski

This article outlines the results of a computer simulation reproducing the transport of a mixture of air and methane following the outburst on 25 November, 2005 in transport gallery D-6, bed 409/4, at the ?Zofiówka? hard coal mine. Based on a mathematical model, numerical method and boundary conditions from the disturbance caused by the outburst, the Ventgraph system of computer simulation programs was adopted for the study. We performed a computer simulation of the influence exerted by the outburst on the propagation of the air and methane mixture, and compared the results of this simulation with those of the actual event as registered by sensors of the mine monitoring system. A validation of the model allowed us to present temporal changes in the concentration of methane and air along flow routes. Keywords: mine ventilation, outburst of methane, numerical simulation, monitoring system.

Jan 1, 2008

By J. Persson, N. G. Bliss

Electric furnaces used for smelting and those used for scrap melting exhibit different performance profiles in terms of electrical characteristics. However, the underlying principles are the same for either case. The rationalization of these variables is a major concern for furnace operators and designers. This paper presents the results of a two year study of high speed real time data from a number of electric furnaces around the world, covering a very wide range of design philosophy and product manufacture, to provide a better mathematical insight into rationalizing the furnace operation.

Jan 1, 2004

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By J. M. Richards

For most of the 20th century optical petrography has been the primary petrological and mineralogical tool used to characterize coal. The development of quantitative SEM-based techniques, e.g. QEMSCAN®, for coal began only about a decade ago. The application of these techniques for coal lagged behind other commodities, but they are currently being developed with the aim to provide ?one complete analysis? for coal. Quantitative SEM-based techniques are supplemented by quantitative X-ray diffraction (XRD). Recent indications are that these more modern techniques cannot replace the ?standard? petrographic and chemical evaluations, but rather complement them where and when required. The great advantage of quantitative SEM-based techniques is that they are very rapid, with the result that large volumes of samples can be processed on a routine basis. This is ideal for coal type identification, since the results can be used in the creation of ?intelligent? composites. This can lead to the more speedy evaluation of coal deposits by reducing the number of samples on which detailed metallurgical and characterization test work is required, without an increase in the overall statistical error of the resource model. Coal petrography, however, remains important for the prediction of the coking characteristics of certain coals and coal products. As a consequence it is therefore important that any coal laboratory be able to produce data with confidence. This requires strict quality control and assurance protocols that adhere to international standards. Keywords coal petrography, coking strength, scanning electron microscopy, QEMSCAN®.

Nov 1, 2013

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2slags that are typically encountered in the production of manganese containing stainless steels. Gas equilibration-quenching technique was employed in measuring the activities. Activity of Mn in Pt-Mn alloys were redetermined at 1600°C which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600°C. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient repression models were developed to predict the activities and activity coefficients of MnO in slags at 1600°C. Keywords: activity, MnO, slag.

Jan 1, 2004

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By Jeremy Bosman, Johan de Korte

Traditionally the feed to coal preparation plants was de-slimed at 0,5 mm. The +0,5 mm size fraction was processed via dense-medium cyclones and the -0,5 mm size fraction was beneficiated with froth flotation, water-only cyclones or spirals. With the introduction of large diameter cyclones, the aperture sizes of de-sliming screens have progressively increased to about 3 mm in the belief that the larger cyclones are not able to effectively beneficiate coal which has a particle size below the ?breakaway? size. The efficiency of separation in the large dense-medium cyclones is improved by presenting a coarser feed to the units. At the same time, the capacity of the de-sliming screens is increased due to the larger screen apertures and in effect, the throughput capacity of the dense-medium section is increased. The 3 x 0,5 mm size fraction, which was previously processed in the dense-medium cyclones, is now added to the fine coal size fraction and processed by water-only methods such as Teetered Bed Separators (TBS) and spirals. Whether this practice is the most economical way to process the 3 x 0,5 mm size fraction requires further thought since the best processing route for the 3 x 0,5 mm size fraction will depend on a number of factors, amongst which are: o The washability of the coal and the amount of near-density material o Processing efficiency o Specification of the required product o The price paid by the customer for the product o The cost of processing the coal Breakaway size The ?breakaway? size is defined as the particle size below which the Epm of the smaller particles starts to decrease significantly. Bosman1 provides an approximate breakaway size versus cyclone diameter (Figure 1). It should be kept in mind though that the Epm of the small particles is a function not only of the cyclone diameter but also of feed pressure, medium density, medium viscosity, particle shape and density, top-size of particles in the feed, etc.

Jan 1, 2006

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

By D. G. Hulbert, D. J. Oosthuizen, D. de V. van der Spuy

Expert Online, as a software system, is aimed at providing plant operators in the minerals industry with effective training and on-the-job assistance. It incorporates a number of features to achieve this goal, of which the most important is its ability to explain the dynamics of the plant and control system in simple language, mimicking an informed plant expert who has online access to the inner workings of the plant and control system. This is made possible by a novel form of Artificial Intelligence, called the Interpreting Expert System. Previous implementations of the IES were only capable of explaining controller actions. Expert Online will extend this capability to also perform the more difficult task of explaining process behaviour. Expert Online will implement three main processes, namely the accumulation of data from the controllers and plant models, the interpretation, processing and filtering of that data and lastly communicating the relevant information to the user, both as written messages and in other audio-visual forms. Although Expert Online is aimed at the operator, other plant personnel, like supervisors and plant managers, will also benefit from it. This paper focuses on the structural and functional design of Expert Online for implementation on the latest version of Mintek’s open control platform, PlantStar, highlighting advances and additions since the previous implementations of the Interpreting Expert System and concluding with an example illustrating some of the principles.

Jan 1, 2003

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

Changes in reductant and energy inputs which are required to adjust the slag composition in anilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input does also hold for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By L Tolmay, L Nair

Investor confidence can be compromised when one observes large discrepancies between the SAMREC reserves and the mining plan. It is therefore up to the responsible persons to ensure that all contributing factors get taken into account when determining a reserve declaration. Confounding factors could be further aggravated by large oscillations in the commodity price thus resulting in major changes to the mining plan, if the accepted price was either too optimistic or pessimistic. Additional factors that must receive our attention are, uncertainty in geological facies type, mining practices, geology and grade estimation. The paper outlines (in the authors? opinion) some of the important factors that need to be taken into account, in order to ensure proper alignment between the estimates of the life of mine (LOM) reserve grades, and the corresponding actualisation of the mining plan. These parameters provide an historical insight into what actually happens when attempts are made to implement the mining envisaged in the LOM plan. In turn these allow judicious application of discount factors that enable a realistic estimate of SAMREC reserve classification and declaration. Some of the factors that will be covered are: - 1) Flexibility of developed reserves and the ability to maintain this. 2) Mining control mechanisms and their overall efficacy. 3) The ability to extrapolate facies types and its effect on grade control. 4) The ability to control the mining mix and value variation. 5) Finding a happy medium between optimism and pragmatism.

Jan 1, 2007