Search Documents

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

This is an abstract from Environmental Service and Technology (Vol 32 No 20 1998) which will be o finterest to South African Mining and Metallurgical Scientists, involved in chromium mining and Metallurgical processing. Maybe the scourge of our dams and reservoirs?the water hyacinth can be put to good use! The novel technology of phytoremediation embraces plant accumulation processes for the cleanup of toxic heavy metals and organic chemicals. Several plant species have been identified that are excellent hyperaccumulators of a number of heavy metals, e.g., Brassica juncea (Indian mustard) and Thlaspe caerulescens (Alpine pennycress). Other speciesincluding Myriophyllum brasiliense(Parrot?s feather), Salixsp. (willow), and Popullussp. (poplar) have also demonstrated phytoremediating abilities.

Jan 1, 1999

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electro-chemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electrowon. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present solution will contaminate the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis. This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated: Co2+concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By T. Proietti, L. Mongiovì, L. Simeoni

Reliable estimates of the kinematic characteristics of movements are obtained by using a statistical model SSM. This model represents a useful tool for the management of alert and alarm systems. L'élaboration des données du déplacement médian d'un modèle statistique SSM opportun fournit des estimations fiables des caractéristiques cinématiques du mouvement. Le modèle peut être ainsi utilisé pour la gestion des systèmes d'alarme. Die Bearbeitung von Bewegungsdaten anhand eines geeigneten statistischen Modell SSM ergibt vertrauliche Abschätzungen der kinematischen Eigenschaften der Bewegung. Das Modell kann also für das Management von Alarmsystemen verwendet werden.

Jan 1, 2003

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest are reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By R. J. Durrheim

The seismicity of the Witwatersrand Basin and Bushveld Complex has been analysed, revealing significant differences in source and damage mechanisms. A comparison of mining taking place at similar depths and extraction ratios indicates that the seismic energy release rate is considerably lower in the Bushveld Complex. Technologies introduced in the past decade to manage the risk of rockbursting are reviewed and assessed. These include geophysical methods to detect hazardous structures ahead of mining, new mining layouts and support systems, and the mechanization of in-stope processes. Despite important differences in geology, in situ stress, mining layouts and methods, there are many opportunities for the reciprocal transfer of knowledge, experience and technology between the gold and platinum mining sectors to improve the management of the rockburst risk.

Jan 1, 2005

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 25th August, 1976. Dr R. E. Robinson, (President) was in the chair, and declared the meeting open at 16h00. Obituaries The president: It is my sad duty to announce the death of the following members of the Institute : P. A. Creewell, Life Fellow; A. S. Davis, J. S. Hay, P. O. Large, N. McCaskell, and H. G. M. McKerrow, Life Members; C. L. Bererge, Fellow; T. Bulloch, G. Douglas, R. W. Forrester, and C. G. P. Sack, Members; P. R. Garcia, W. A. Naude, and J. P. Slager, Associates. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on March 17th, 1976, as published in the June issue of the Journal? Agreed. Welcome The President: It is my pleasant duty to welcome a number of guests and distinguished visitors this evening. First, I would like to welcome Mr R. Plumbridge, the President of the Chamber of Mines, and Mrs Plumbridge. We have had very close co-operation with the Chamber of Mines, and it is particularly gratifying that Mr Plumbridge has had time to be with us this evening in spite of very heavy engagements. Ook 'n spesiale woord van verwelkomirg aar mrr. N. Orsmord, die Staatsmyringerieur, en mev. Orsmord. Ors wil hierdie geleertheid gebruik om mrr. Orsmord geluk to wens met sy aarstellirg as die Staatsmyrirgerieur en die hoop uitspreek dat dit baie jare van samewerkirg met hierdie Irstituut sal beteker. We also welcome guests who, in one way or another, have been able to attend most of our Annual General Meetings, the Honourable I. B. Dillon, the Minister of Mines of Rhodesia, and Mrs Dillon. Once again we welcome them most heartily to our Annual Meeting. I would also like to welcome the representatives of many of our sister institutions : the Honorary Treasurer of the AS & TS, Mr D. G. Maxwell; the President of the South African Institution of Mechanical Engineers, Mr A. R. Adams; the Vice-President of the South African Institute of Electrical Engineers, Mr K. A. H. Adams, and Mrs Adams; the President of the Institute of Certificated Mechanical and Electrical Engineer s, Mr Martin and Mrs Martin; a member of the Executive of the South African Institute of Civil Engineers, Professor G. Bright ; the President of the South African Chemical Institute, Mr Vic Shuller, and Mrs Shuller; the President of the Institute of Welding, Professor F. P. A. Robinson, and Mrs Robinson; the President of SACPE, Mr M. R. Gericke ; the President of the Institution of Metallurgists, South African Branch, Mr D. R. Allen; the President of FSPE, Dr P. J. D. Lloyd, and Mrs Lloyd ; Mr A. J. H. Pole of the Association of Mine Managers, and Mrs Pole; and Mr M. D. Hoskin of the South African Institute of Foundrymen. A special word of welcome to Mr G. C. Young of our Orange Free State Branch, and Mrs Young ; and to Mr E. J. Jackson of our Witbank/Middelburg Branch. We have great pleasure in welcoming Dr F. M. Naude, the Scientific Adviser to the Prime Minister, and Dr W. C. J. van Rensburg, Technical Director of the Minerals Bureau. The latter is a new organization, and we hope their attendance here this afternoon forecasts a long period of co-operation between the Minerals Bureau and this Institute. Ook wil ek hartlik hier verwelkom die Rektor van Die Randse Afrikaanse Universiteit, professor G. van N. Viljoen. Ors het baie noue samewerking met die Universiteit gekry, en ek wil ook bier verwelkom die twee verteenwoordigers van die Geologiese-afdeling en die Chemie-afdeling, naamlik, dr C. Roering en professor G. W. Holzapfel. Last, but by no means least, a word of welcome to a very old friend, Mr Eric Boden, the Manager of AS & TS. To all our guests, a very hearty welcome to this our Annual General Meeting. Membership The President: It is required by our Constitution that I announce the names of a number of candidates who have been elected to various grades of membership. The list is a very long one, and I suggest that we simply record that these names will be published in the Journal. Any one who wishes to comment on these members should do so in writing to our Secretary. Agreed. Fellows: G. Paterson, P. H. Adler, F. W. G. Schoning, J. P. de Villiers, F. I. de Waal, J. R. H. Shaw. Members: C. J. Slavin, P. J. Perkins, R. J. I. Butler, A. M. Hattingh, C. E. Alvey, J. A. Engelbrecht, P. L. Gouws, J. P. Martin, J. F. Taylor, K. A. G. Blendulf, A. R. Gibb, W. E. Smith. Associate Members: D. R. Broderick, D. F. Cilliers, D. N. Stuart, P. Kraus, B. G. Pinder. Associates: D. E. Gibbon, D. F. Jacobs, R. F. W. Swanepoel, R. D. H. Bebb, H. H. Vernall, R. D. Gibson, J. P. van Wyk. Graduates : A. N. Morris, D. J. Payne, G. S. Worthington, A. S. Dennison, A. R. Godfrey, N. Holloway, W. J. Rankin, G. S. Lyndon, R. J. van Proctor, J. J. Versluis, G. M. Miller. Students: B. J. Rabie, G. D. Webber, W. L. Blair, I. D. Mathews, K. McVey, S. W. Beer, R. W. J. Bentley,

Jan 10, 1976

By P. Foster

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident reconstruction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed, namely (i) remote control continuous miner operation and (ii) free steered vehicle sight-lines, which demonstrate the practical use of VR in this area.

Jan 1, 2004

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By I. Jones

Geologists, engineers, technicians and surveyors have successfully utilized technical software in the mining industry for over 30 years. Software for processing survey, geology, mine engineering and planning information make these functions more efficient by automating repetitive tasks and reducing data processing errors. While these systems have been improved incrementally overtime, new systems that represent giant leaps in technology have been introduced to help mining operations increase productivity and reduce costs. However, their widespread use within the industry has left individual companies without a competitive advantage. Additionally, the ability of these applications to provide the productivity improvements required in today’s uncertain market conditions has since peaked. The next wave of technology—integration of independent software applications—is just starting to emerge and will have a significant effect on the productivity of mining operations. To reap the productivity gains required to remain competitive, mining companies must exploit the collective knowledge and experience of every employee in the organization. Integration of independent software application allows companies to leverage information from all activities, enabling staff to make better decisions to improve productivity. This paper outlines the importance of integration as productivity enabler. Key performance indicators, strategic mine planning, resources management and mine-to-mill integration are discussed as processes that enable productivity. The Gemcom Enterprise Mining System (GEMS)is introduced as the industry’s first integrated solution that enables these productive processes. The paper concludes with a comment on the level of change required to realize the benefits of integration.

Jan 1, 2003

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By G. H. Lind

Seven full and partial pillar extraction operations were visited in New South Wales, Australia, in the early parts of 2001. Certain factors unique to these operations have led to the general success of the safe and economic extraction of these coal pillars. Some of these factors attributable to the overall success of these operations are discussed in this paper. In particular, geotechnical mapping, specific legislation pertaining to pillar extraction, mining methods, the role of temporary supports and training are described. It is found that some of these factors have useful attributes which could be used to design a methodology for extraction of underground coal pillars in the Witbank and Highveld coalfields of South Africa.

Jan 1, 2002