Search Documents

Students The South African Institute of Mining and Metallurgy (SAlMM) places a high value on its student members, for these people will ultimately become corporate members and will, it is hoped, play an active role in the affairs of the Institute. Why should young persons at University or Technikon want to become members of our Institute? There are several reasons.

Jan 1, 1991

By R. G. B. Pickering, B. Ebner

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock—though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominantly by means of scraper buckets and scraper winches — these were first introduced in the 1920s.Support is still mainly rock, either in sit pillars or backfill, or alternatively wood. Just as themining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ‘trackless mechanized mining’ was introduced in the early 1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to’ off the shelf’ equipment. The move to introduce room-and-pillar mining into the narrow UG2reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long holedrilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds—maximum reef recovery with minimum waste dilution. All these mining methods are still dependent on blasting to break the rock. The cyclic nature of mining by blasting places severe constraints on the rate of face advance that can be achieved and consequently the utilization of the invested capital. For narrow reef hard rock mining to break out of these constraints and to really make progress in the 21st century it is necessary to follow the lead of the soft rock mining industry and change the technology of mining. In the underground coal mining industry, coal cutting has been proved to be the most cost-effective solution. In narrow reef hard rock mining the future must be based on the development of non-explosive methods of rock breaking that in turn are integrated into continuous mining systems. Non-explosive so that the mining operation can be conducted on a continuous basis, with nodelays for the removal of blasting fumes. Continuous mining also maximizes the return on the capital invested in developing the mine. Rock cutting will define the stope width and that in turn will be designed to minimize waste dilution; it will also minimize damage to the hanging and create a safer environment. Mechanization makes it possible to automate the mining process and further improve safety by positioning the operators in a safer environment. This paper defines the work to evaluate cutting processes carried out by Sandvik TamrockVoest Alpine. The evaluation was in the UG2 and the pyroxenite and norite typical of the Merensky Platinum Reefs. A novel form of mining machine is proposed that will utilize existing technology. Finally the paper describes the interaction between Sandvik Tamrock Voest Alpineand Lonmin Platinum and the initiation of an agreement to develop and trial a prototype hard rock narrow reef mining machine.

Sep 1, 2001

By G. M. Brown, B. J. Ebacher, W. G. Koellner

Introduction There is a continual economic push to increase the productivity of mobile material handling equipment used in open pit mines. This includes the largest electrical machines: excavators (draglines and shovels) and haul trucks (Figure 1). Existing DC drive systems used on this type of equipment are a mature technology. They have no further economic potential to accommodate larger equipment be-cause of the high maintenance costs and the trade-off between power, speed and space limitations of their DC traction mo-tors. In recent years the large-scale introduction of AC drives in the rail transportation sector1,and the availability of poworful GTO and IGBT modules have led to the devolopment of compact, powerful, an drugged AC inverter drives specifically adapted to the mining market2,3. The major advantage of AC drives stems from the squirrel cage induction motor which eliminates the DC commutator. This leads directly to higher speed, increased power density, higher reliability, greater efficiency and lower maintenance of the traction motors. In the context of excavators and haul trucks, additional benofits driving the move to AC are (i) increased production rate due to higher machine speed, and power density, (ii) increased reliability and lower cost inverters using 3.3 kV IGBT's, (iii) active front-end (AFE) technology that improves compatibility with the mine power grid and an proved dynamic response,(iv) intelligent converter design that provides increased fault tolerance, (v) contextual maintenance software that facilitates trouble-shooting, and (vi) remote diagnostic capabilities. This paper describes how these and other features of AC drives lead to higher productivity in mining shovels, draglines, and haul trucks. Minimize the cost per ton of material moved The overall goal that drives design and sales of excavators and haul trucks is the constant requirement to reduce the cost per ton of material moved. Whether this involves blasting, loading trucks, or hauling material to the crusher or waste dump, equipment that reduces the cost per ton of material moved contributes to a more profitable operation. An accurate determination of the true cost per ton to move material must consider every aspect of the equipment and the circumstances under which it is used. Procurement and capital costs, fuel, operating, and maintenance costs over the useful life, and eventually the cost of scrapping should all be taken into account to determine the real cost per ton of moving material. We will focus on two broad areas that relate to the equipment itself; factors influencing the amount of material moved (Table I) and factors influencing the cost of material moved (Table II). Emphasis will be given to those elements in the tables that most influence the productivity of excavators and haul trucks due to the application of AC drive technology. Maximize the amount of material moved Maximize production rate he production rate refers to the quantity of material that can be loaded or moved per hour. This generally involves larger, faster, and more powerful equipment that operates more reliably to minimize down-time. AC motors Figure 2 compares the hoist motor speed-torque response of two 77 t (85 short ton) shovels, one AC the other DC. The absence of commutation limits on the AC motors enables the AC shovel to operate with a greater area under the speed-torque curve, resulting in faster lowering speeds and reduced times for the swing to return to the pit. This is especially important for short swing angles where the operator may have to wait for the dipper to lower. Reducing the cycle time by 6 to 8 seconds at the shovel translates into an increase in shovel production of about 20%. Larger equipment The bucket capacity of excavators has increased approximately 100-fold over the last century. Figure 3

Sep 1, 2001

By W. A. Hustrulid

CONTENTS PART I The theory of percussive rockdrill operation. Blow frequency Piston impact velocity and blow energy Thrust requirements Prediction of penetration rate Drillsteel life Bit wear PART II Measurements of percussive rockdrill performance Thrust-penetration rate measurements Blow frequency Piston impact velocity and blow energy Prediction of penetration rates The effects of hole diameter Thrusts applied by men Bit wear Appendix I Experimental procedure and rockdrill and drill steel specifications Appendix II Piston impact velocities and energies PART III Practical implications. Provisions of adequate thrust Conclusions INTRODUCTION In South African gold mines some 100 million tons of rock are broken each year by drilling and blasting. Only minor improvements to this method of rockbreaking have been made since the general introduction of pneumatic rockdrills for stoping 50 years ago and, more recently, of drillsteels tipped with tungsten carbide. The combined total cost of drilling and blasting amounts to almost R0,50 per ton of rock broken, which is just short of one quarter of the direct cost of stoping or development. Rockdrilling accounts for about R0,25 of the total cost of rockbreaking, of which RO,12 represents labour costs and R0,13 the cost of drillsteels, rockdrill spares and power. Mine air compressors use over 7 X 108 kWh of electric energy a year, amounting to 7 percent of the total electric power used by the gold mining industry. The efficiency of percussive rockdrilling is, therefore, of considerable significance to mining costs. Over the past four years the Mining Research Laboratory of the Chamber of Mines of S.A. has been engaged in experimental studies of percussive drilling. These experiments were conducted at test sites on Robinson Deep Gold Mine and Vlakfontein Gold Mine, made available by Gold Fields of South Africa, Limited. Three rockdrills, designated types A, Band C, of different manufacture, were used in the experiments which involved the measurement of the following operating characteristics: 1. Throttle air pressure 2. Applied thrust 3. Penetration rate 4. Air consumption 5. Blows per minute 6. Drill steel revolutions per minute. The results of these investigations are presented in three parts. Part I, "The theory of percussive rockdrill operation" which provides a concise, mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions and operating conditions, and an analysis of the bit and gauge wear of drillsteels. Part II, "Measurements of percussive rockdrill performance" in which the experimental results are presented in terms of thrust-penetration rate curves at different throttle air pressures and throttle pressure-air consumption curves, which are shown to agree well with the predictions of theory. In addition, data relating gauge wear on the drillsteel and penetration rate to the distance drilled are discussed. Part III, "Practical implications" in which an analysis of the status of thrusting devices is made and the benefits that would derive from using uptimum thrusts are discussed.

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of 'average' (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by 'average'? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual's quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the 'average' Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being 'average' recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the '50 per cent of maximum oxygen intake' level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and 'optimum' levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors' ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at 'optimum' levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that 'The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample'. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry's stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

By B. Mienie, J. F. Morrison, C. H. Wyndham, M. J. Martinson, N. B. Strydom

Contribution to discussion M. J. Martinson (Associate Member)*: Application of the simple selection test mentioned in the penultimate paragraph of the paper (reference to a more detailed description of the test would not have been inappropriate) should assist South African mining engineers to make more efficient and possibly more humane use of available labour. The authors mention that the test 'is in use in the gold mining industry', and it would be interesting to know the extent of this usage in terms either of number of mines or as a percentage of the total number of labourers employed on 'heavy' tasks. The paper would have been of greater interest had the authors attempted to relate their findings to the statistics of labour usage in gold mines, members of the Chamber, and to the 'heavy' tasks in particular. On this the authors confine themselves in their Introduction to the somewhat ambiguous statement that 'A relatively high proportion of the 360,000 Bantu mine labourers are employed underground on manual tasks'. To appreciate the practical significance of the authors' work one needs a detailed breakdown of the underground labour force by occupations, together with estimates of quantities such as: (a) total stope and development tonnages moved manually per shift: by shovelling by shovel/tram by tramming together with distances and any other relevant data; (b) theoretical energy expenditures required to accomplish (a); (c) actual energy expenditures required to a accomplish (a); (d) energy theoretically available to accomplish (a) based on 50 per cent of the total maximum oxygen intakes of the labour force allocated to these tasks. Analyses of this sort on an industry basis might demarcate the more promising areas for detailed investigation. Stress is often laid on the need for increased mechanisation to increase stope productivity, but it may be questioned if enough is known about the characteristics, performance and potential of our underground labour force to warrant blind acceptance of stope mechanization as the industry's panacea. Provided that health and safety are not compromised, the ultimate yardstick for assessing any form of stoping is profitability; obviously the industry must investigate very thoroughly any form of mechanization which might reasonably be expected to increase profitability, but it should also be remembered that a radical overhaul of existing systems-which have after all evolved by trial and error over the past 75

Jan 11, 1968

By P. R. Jochens, D. D. Howat, C. W. Wolhuter

Prof D. D. Howat (Member): I am a man with a grievance this afternoon. The other authors of the paper entered into a conspiracy to ensure that I presented the paper, and finally even had the audacity to say that this was the least that could be expected from me as I had done so little of the other work. Looking at the distinguished audience here that includes some figures who have forgotten more about cement that some of us have ever learned, I realise how right the other authors were. I feel very much cast in the role of the fool who was pushed in where angels fear to tread. I hesitate to say, Sir, that I would not use the word angels in any definition of the authors of this paper. In presenting the paper, may I try to put forward a few simple points about cement that are probably as little known to the majority of the audience as they were to me-at least until very recently. Concrete, made by mixing Portland cement, sand, crushed rock and water is the most widely used constructional material in the world. Generally the production of actual Portland Cement is about two-thirds that of steel and by the time this is formed into concrete the total is about five times the world tonnage of steel produced. A very rough approximation suggests that world consumption of concrete is about one ton per person per annum. Apart from fresh water mankind consumes no other material in such quantities. What mankind originally required was a mortar to be used for joining blocks of stone or bricks. Such mortar was originally made from limestone burned in a kiln and then mixed with water. Production of mortar of this type began over 5,000 years ago. Some samples from pyramids in Egypt have shown this mortar to be in good condition although over 4,500 years old. The progress of technological development was very slow until 1824 when an English bricklayer, Joseph Aspidin, patented a new mortar material which he made by burning limestone and clay together in his kitchen stove. Aspdin called his product 'Portland Cement' because, in colour, it resembled a well-known building stone quarried in the Isle of Portland on the south coast of England. Aspid's same types of raw materials are used today in modern cement production and the product is still referred to as Portland cement. A lime-containing material such as chalk or shell and a clay-type material such as shale, slate or clay itself, are mixed in the required proportions, ground and fed to a kiln where the minimum burning temperature is about 1,500°C. The raw materials react to form hard chunks of a material known as 'clinker'. About 5 per cent of gypsum is added to the clinker and the mixture is then ground to a very fine powder, the function of the gypsum being to control the rate of setting of the concrete. The key oxides in cement production are lime, silica, alumina and iron oxide. The possible reactions occurring during and the products of the burning process are shown in Table I.

Jan 12, 1968

On 23rd October, 1969, 54 members of the Institute set out at an early hour from Rand Airport in two chartered Dakota aircraft for a visit to the Hendrik Verwoerd Dam site. The weather was at the start rather unpromising but after passing Bloemfontein the overcast cleared and it turned into a glorious day for a most memorable visit. The Institute is indebted to U.C-Dumez-Borie Dams Limited, the main civil engineering contractors, and Mr J. D. McNamara their executive manager, for the very excellent arrangements made for this excursion. From the time the aircraft landed till a slightly belated departure the organisation of the extensive tours arranged for the parties was quite outstanding and a matter for congratulation to all concerned. At each of the many places visited there was a senior official to give an authoritative and comprehensive description of the work under his control. In addition the guides on the buses, loaned by the Department of Water Affairs, kept up an interesting running commentary throughout the day. A further much appreciated facet was the introduction of many of the experts on the site and a brief talk by each after an excellent lunch served at the recreation club. Each visitor also received a brochure with a progress report and a detailed site plan, with various sections highlighted in colour, and obviously prepared at the cost of much time and effort. The visit included tours of the large dolerite quarry, where some 150 000 tons of rock are removed each month, the 42 in. gyratory primary crusher, the secondary crushing and screening plant, the rod mill plant for sand production, and the automated blending and concrete batching plant. The transport of mixed concrete by 'silobuses' to the 6 cu. yd buckets of four Blondin cableways, two of which are radially movable and two with buffing towers, and the placing of the concrete in the huge blocks of the wall was watched from a vantage point. The most interesting part of the visit was without a doubt the inspection of the wall itself and the explanations of the many intricasies of its design and care in construction, covering aspects such as positioning of galleys, interlocking of blocks, reinforcement, refrigeration, actual concrete placing, subsequent grouting, etc. Other points of interest were the very complicated design of the wall itself, the river diversion plans, with three stages of coffer dams, the spillways, and the very well cut penstock tunnels.

By Dr. T. L. F. Muller

INTRODUCTION During the past decade a wealth of knowledge has been acquired about the mechanisms and reactions responsible for the physical properties of metals. In the field of steels, in particular, research of a fundamental nature has enabled us to interpret mechanical properties such as hardness, brittleness, creep strength, etc., in terms of atomic interactions. So rapid has been the development of physical metallurgy in some fields that publications are often outdated by the time they appear in print. The development of new steel products has been rather empirical by nature in the past and only during the past few years have new products been "designed" in terms of known physico-metallurgical phenomena. However, although this is a great stride forward it should be added that the development of a commercially successful product is a far more complicated process. In addition to the physico-metallurgical background this requires consideration of factors such as low production cost, market research and probably most valuable of all, an interested end user to co-operate in the development. This paper deals rather briefly with three of the most recent developments in steels in Britain with which the author has had some association. The main purpose of this is to demonstrate how the improved properties of the new product are based upon established physico-metallurgical phenomena. Generally speaking a commercially successful product of the type described here offers similar properties to that of an existing product at lower cost or has improved properties or features such as greater ease of cold forming, at similar cost. ULTRA-FINE GRAIN STRUCTURAL STEELS The development of higher yield strength structural steels dates back over a considerable number of years and has led to a variety of types. The one described below contains niobium as a grain refiner in an otherwise conventional mild steel matrix. By controlled rolling in a strip mill considerably increased yield strengths are obtained. In Fig. 1 are shown somewhat diagrammatically the relative hardening effects of carbon and manganese on ferrite. It will be seen that strength is enhanced by the solid solution hardening effect of manganese and the pearlite content. An obvious limitation of high pearlite content is a lack of cold workability and weldability. Manganese has to be restricted to low levels for the same reasons. The two other mechanisms which are known to impart higher strength are precipitation hardening and grain refinement. Precipitation hardening is impractical in most cases for structural steels and it is therefore clear that only grain refinement remains as a potentially useful strengthening mechanism.

By J. H. French, O. E. Lissner

S. J. Venning (Member): The authors should be congratulated on producing such concise data from the plethora of experimental report results. Their observations on the cost of liners calls for some comment however, as the really unique feature about liners in South Africa is that they can be obtained so cheaply. Attention has been focussed on the 1961 cost of white iron at R50 per ton for chill cast block liners while manganese steel liners are reported as costing as much as R250 per ton. The former are however, a relatively heavy, simple casting with a low labour content and reasonably high percentage productivity, made from metal melted in a cupola. The capital investment to produce this type of casting is low compared with that required to produce manganese or other alloy steels. The chill cast liner block is always a production item and is cast in a permanent mould. Almost all manganese mill liners, except perhaps small aperture screens, are sold for considerably less than the R250 per ton quoted by the authors. Where a price of this nature is asked it would be because the design of the casting demanded is complicated or leaves little metal to carry the labour and other costs of production. As reference has also been made in the paper to liner costs in America, prices for similar types of liners obtained during a visit to Canada and the U.S.A. in 1961, could be of interest: Material Price per Location short ton Ni-hard R250 Elliot Lake Body liners block type Ni-Hard R300-310 FAS New York Mn Steel R280-290 FAS New York Screens (grids) slotted Cr.Mo. Steel R600 FAS New York hole Ni-Hard R320 Elliot Lake At this time the price of comparable manganese steel block type liners on the Witwatersrand was between R145/R155 per short ton. White iron in Canada was then quoted at about R150 per ton, but as Ni-Hard gave a life of at least two to twoand-a-half times that of white iron, it was a much more attractive proposition particularly when relining and down time costs were taken into consideration. There is little doubt that most foundries would welcome clear and complete specifications of the customers requirements and systematic checks to ensure that these specifications are being met. B.S.S. or other accepted standards should form the basis of these, and periodic inspections should be undertaken to ensure that only those foundries capable of complying should be included as suppliers. The authors have referred to new designs, but can the industry really call the grid and plate new when the patents were taken out during the second world war and the sawtooth block has been used for at least 35 years. Unfortunately, far too little thought and consideration are normally given to the ultimate mill liner design while the mills themselves are on the drawing boards. The position and size of the door opening, which is the key to the ultimate shell liner configuration, the drilling of the

Jan 9, 1968

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

If the Journal is to fulfill its mandate to the mining and metallurgical industry, it needs to expand its readership and, by implication, membership of The South African Institute of Mining and Metallurgy. This we hope to do by increasing the appeal of the Journal to a wider audience through the inclusion, in addition to our high-quality research papers, of equally high-quality papers, articles, and contributions that will be of interest to our less research-minded members.

Jan 1, 1990

The Iscor Board has given its Mining Division the authority to proceed with detail engineering and design for a Heavy Minerals Project which comprises a mine in Northern Province near Gravelote, a mine in KwaZulu/Natal near Richards Bay and a central processing complex with a beneficiation plant and smelter which will be located near Richards Bay and Empangeni.

Jan 1, 1996

By D. D. Howat

In the field of high temperature smelting processes there have been two dramatic changes in the past twenty years. These are, first, the application of tonnage oxygen for direct injection for the refining of molten iron and other metals and to provide the means of enriching air used for the combustion of fuel. Second, the application of electric power for the generation of high temperatures in place of the combustion of fossil fuels. Of these two developments the application of tonnage oxygen for the refining of molten iron has virtually revolutionised the steel industry throughout the world. The magnitude of this development is exemplified by the fact that less than 5 per cent of the world's steel production in 1960 was made by this process or 16 million tons out of a total of 350 million tons of steel produced, while in 1970 over 40 per cent of the world steel production was made by this process, ie, 251 million tons out of 628 million tons total. In the same period the proportion of steel produced by the old-established open-hearth process has shrunk from 75 per cent to 38 per cent. In the whole history of the development of high temperature metallurgical smelting processes there has never been anything remotely approaching this. The other development, the application of electric power for the generation of high temperatures has not had the impact of the oxygen injection process but I believe that what we should call the electric smelting revolution in metallurgical processes has very far-reaching ramifications for steel production and other pyrometallurgical processes. This may seem a bold and brash statement but it must be remembered that the oxygen injection process constitutes a link in the chain critically dependent upon the production of vast tonnages of molten iron from very large modern blast furnaces. The Achilles heel of this chain of processes, upon which such a large percentage of the world's supply of steel depends, is the availability of metallurgical coke in turn dependent on natural resources of coking coal. Without any exception each industrial country in the world faces a shortage of resources of coking coal and in some cases a critical shortage. Certainly within the present century the major iron and steel producing countries of the world will face this critical shortage of coking coal and major modifications to steel making processes will become inevitable. W. F. Cartwright (Deputy Chairman of B.S.C) said recently that there are considerable doubts as to whether the world will be able to provide enough coking coal to meet world steel demands from the late 1970's onwards if the B.F.remains the main means for making iron from ore. This is one of the supreme ironies of the world metallurgical situation to-day when the technology of iron and steel production has reached an extremely high peak of technical efficiency. The newest modern iron blast furnace capable of producing 6 000 to 8 000 tons per day of molten iron represents probably the most efficient piece of high temperature metallurgical plant and operation known to man. The conversion of this molten iron into steel by the oxygen injection process has made available to the engineering industry steel of a quality and at a price which is quite remarkable. Yet this vast metallurgical pyramid rests on the completely insecure and uncertain foundation of inadequate world resources of coking coal. The shortage of reserves of coking coal in this country is acute and it is possible that these resources will be exhausted within the next twenty years. Yet unless some completely unexpected catastrophe occurs the demand for steel in this country will probably rise at a faster rate than in the Western world due to the expansion of the Bantu population and the increased standard of living. To offset the inevitable shortage of coking coal are our much greater resources of bituminous coal which although of low grade provide a suitable fuel for electric power generation. The geographical disposition of the coal fields in relation to the great industrial areas of the Transvaal makes it inevitable that the development of the pyrometallurgical industries must depend heavily on electric power. The position in this country with regard to electrical power generation and consumption is rather anomalous. Per capita consumption of electric power is high - in 1964 almost twice the world average of 870 KWH and twenty-five times the average of 34 KWH for the Continent of Africa. In 1964 fifty-four per cent of the total world electric power was used in industry - the ratio being approximately 1/9 mining to manufacturing uses. As shown in Table I in 1969 67.2 per cent of the total output of electric power from ESCOM was used for mining and other industrial uses but almost in the ratio 6/4 mining to industrial uses. These figures emphasise the enormous importance of the mining industry to the economy of this country and underline the major contribution made by the gold mining industry. What is of very significant importance is that although the mining industry remains by far the largest single consumer of electrical power the consumption of power for industrial uses is rising rapidly as shown in Table II.

By L. Thomson

"The smelter at Sudbury Integrated Nickel Operations, located in Sudbury, Ontario, operates a single electric AC furnace. This furnace treats nickel sulphide concentrates produced by Glencore and third-party feeds and as such its performance is key to the company’s nickel supply chain. Currently the plant has two shutdowns per year in order to carry out significant repairs on matte tap-holes.Improved monitoring systems that enable better prediction of tap-hole wear have been a continued focus. The electric furnace is an essential piece of the smelter flow sheet requiring the need for planned tap-hole maintenance along with robust systems for management according to to this plan.The ability to meet our goal of zero harm is ensuring that safe practices are in place. Detailed procedures and cool-down practices have been implemented to ensure that required matte chemistry and temperature criteria can be met during the period leading into a shutdown for tapblock maintenance.A significant repair of the electric furnace will take place in 2015. During this rebuild, the sidewalls and matte endwall will be replaced. There is work underway to improve wall and matte end performance in an attempt to extend the time between rebuilds. This paper will review the approach taken towards this end."

Jan 1, 2014

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By N. F. Mashinini

Optimization of current control systems, proper maintenance and efficient training of personnel are recommendations made to control the amount of dust that underground employees are exposed to on a daily basis in the coal mining industry. This dissertation forms as part of Sasol Mining?s commitment to protect the health and safety of their employees by suppressing and controlling dust at their mines. This study aims to understand the relationship among mining processes, exposure to dust and dust suppression control measures. The research phase of the project was done at the Sasol Mining Secunda complex where underground visits were undertaken to investigate current control systems and also new systems that are being implemented by Sasol Mining. This work was important because it helped determine the sources of dust underground and also to identify the shortcomings of current control systems and to test the efficiencies of the new systems implemented at Sasol Mining. The most important result of the research work was the identification of which underground operators were exposed the most to dust as this assisted in designing a dust suppression system for the areas where these operators worked. The main conclusions of this study are that the current control systems are sufficient for controlling dust and ensuring dust compliance if they are used efficiently and maintained properly.

Jan 1, 2008

Primary roof support represents the first line of defence against rockrelated falls of ground in underground mines, and improper utilization or misunderstanding of the applicability and behaviour of primary support can be costly from a safety standpoint. This is a major concern for underground mines, as roof support is the single most costly expense from a mining operational perspective. This is further backed by the evidence that, in the USA, hundreds of injuries and fatalities still occur each year because of rib, roof, and massive roof falls. Additionally, the fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical anchor bolts, which constitute a large portion (89%) of the 68 million bolts installed each year in underground mines in the USA can vary in cost quite dramatically. To mitigate this concern a study was conducted in 2010 by the National Institute of Occupational Safety and Health, in conjunction with Southern Illinois University of Carbondale, to assess the performance of primary roofbolts in underground coal mines for improved safety and cost. This was accomplished using underground roofbolt monitoring solutions, field data, and numerical modelling to better understand the quasi-static behaviour of underground coal mine roofs and the response behaviour of the bolts. In particular, over 170 instrumented extensometers, closure meters, shear meters, fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical roofbolts were installed at three coal mines across the USA. Of these three mines, two used the room and pillar extraction method and the other used the longwall extraction method. There was no evidence to indicate a difference in performance of the active primary roofbolts compared with the passive primary roofbolts. Additionally, in the initial loading phase, the active bolts showed no difference in loading, indicating that tension bleed-off is of more of a concern than originally thought. Lastly, for the initial computer modelling studies, challenges still remain in obtaining a good match to the in situ bolt measurements and replicating the discontinuous roof rock and in situ bolt behaviour over time.

Jan 1, 2014

By Bosman

Medium suspensions play an integral part in the successful application of dense medium separation for both static and dynamic separators. Although models exist to predict particle movement as a function of medium density and viscosity, these models have been derived on the assumption of Newtonian rheology. Viscosity measurements of medium suspensions have shown that they are non-Newtonian, with a yield stress, and as such cannot be used in the existing models. As a result, medium selection remains an art based upon practical experience and indirect measurements of viscosity such as stability and cyclone differentials.

Jan 1, 2014

By P. van der Westhuyzen

Gone are the days of stock-standard diamond beneficiation and final recovery circuits that could, with minor modifications, be adapted to treat any diamond-bearing ore source. A new era has dawned, offering the opportunity to streamline existing diamond processing operations or develop simpler, more efficient, and economical diamond processing plants, with the focus on more efficient comminution, beneficiation, and final recovery. This change in scene has been brought about by: ? The introduction, rapid development, and maturation of multiple comminution, sorting, and recovery technologies ? The need to adapt to a new standard of project approach post the commodity super-cycle phase, where optimizing existing operations and developing scalable, ?fit for purpose? new mines are fast becoming the norm in diamond processing plants in both primary and alluvial operations ? The quest for energy efficiency and lower labour costs ? More remote and inaccessible reserves (under lakes, tops of mountains etc.). This paper serves to identify some technology advances and demonstrates how these could be considered as replacements for or in combination with conventional technologies to arrive at an optimum techno-economic solution. To name a few applications/technologies: ? Comminution: conventional cone crusher, modified/specialized cone crusher, and the high-pressure grinding roll (HPGR). Although significant advances have been made in recent years, this paper only briefly covers comminution within the beneficiation circuit design ? Waste sorting: NIR (near-infrared) sorting, optical (colour) sorting, XRF (X-ray fluorescence) ? Primary concentration by combining dense media separation (DMS) with either XRT (X-ray transmissive), pulsed X-ray, jigs, or pan plants depending on the application, scale, and economics ? Final recovery of diamonds with either conventional X-ray technology, pulsed X-ray technology, or XRT. From recent studies, it can be concluded that there is no longer a standard solution, but rather the ?right? or appropriate solution. Through combining a sound knowledge of the ore source (ore dressing studies or onmine data gathering) and leveraging off the advances in technologies, one is able, through trade-off studies, to arrive at the ultimate techno-economic configuration, the ?right? solution. Emphasis is placed on maximizing diamond recoveries through appropriate technology selection and minimizing the associated costs in an effort to de-bottleneck or improve efficiencies of existing diamond processing plants, or to arrive at the ideal new diamond process plant design..

Jan 1, 2014