Search Documents

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By N. Singh

Merensky Reef is mined extensively within the Bushveld Complex. In previously mined-out areas on the Merensky Reef horizon there are pillars, potholes and remnants that have not been mined. These unmined blocks of ground on the Merensky Reef horizon can influence the mining of the underlying UG2 Reef. The extent of the influence will depend on the size of unmined ground and the middling between the two reef horizons. This paper quantifies the influence of partially extracted Merensky Reef on mining of the UG2 Reef, and aims to provide recommendations for mining strategies, as well as regional and local support to achieve efficient and safe extraction of the UG2 Reef, for various middlings beneath the Merensky Reef horizon. In some cases it was found that relatively shallow UG2 Reef mining could encounter conditions similar to those experienced in deep and ultra-deep mining environments.

Jan 1, 2005

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By Q. C. Reynolds

Keywords: Pyrometallurgy, plant, photography, GIS, satellite images, Google Earth Google Earth is a piece of software able to display an interactive three-dimensional map of the world, combining aerial and satellite photography with maps, terrain, and user-generated geographical information systems (GIS). Many structural features of the planet, both natural and man-made, are of great interest to the mining and metallurgy field, and in this paper a study is made of the current state of the art of data accessible by Google Earth.

Jan 1, 2006

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By G. Kelly

A new minerals engineering education programme is being developed in Australia which aims to provide tertiary institutions with a package of educationally sound, high quality courses for undergraduates, postgraduates and professionals. The programme is jointly funded by the Minerals Council of Australia (MCA) and the Department of Education Training and Youth Affairs (DETYA) and brings together academics from a number of leading Australian universities, each developing modules in their particular area of expertise. The University of Queensland (UQ) and the Julius Kruttschnitt Minerals Research Centre(JKMRC) are jointly responsible for modules in several areas including comminution, physical separation and circuit design and optimization. Other modules are being developed by the University of South Australia (with the Sir Ian Wark Centre), Curtin University and Murdoch University. The major challenge of the programme is to provide a high standard of education that is accessible to students who may be located at several different institutions and some of whom maybe a long distance from the primary course leader. Rather than taking existing course material and putting it ‘on the web’, the programme aims to improve on past teaching practice through creative pedagogy and the development of interactive multimedia learning resources. Communications technology is used in an unobtrusive way, and the World Wide Web is used to create a flexible, user-friendly learning environment rather than to facilitate delivery of content. This paper describes the instructional design template currently being used and results of early implementation trials with groups of local and remote students.

Jan 1, 2003

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

By J. van Deventer

Ion exchange is widely used in hydrometallurgical operations for the recovery and purification of valuable metals. Special chelating resins have a high affinity for specific elements, allowing the selective removal of low levels of impurities from a background of highly concentrated valuable metal. Solvent-impregnated resins have been added to this group more recently, expanding the treatment options. These products find application in the purification of cobalt-rich liquor prior to the production of high-purity metal or metal salts. Impurities in copper-cobalt circuits that are typically targeted by ion exchange include iron, uranium, copper, zinc, nickel, bismuth, and antimony. Ion-exchange resins can also be used to treat tailings, thereby recovering additional valuable metal and improving the Environmental and Social Governance credentials of the operation. This article takes a look at various applications of ion exchange in copper-cobalt operations

Jan 1, 2023

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By N. J. Castilla, R. Giglio

"Circulating fluidized-bed (CFB) combustion technology has been around for over 40 years, but over the last 6 years it has been commercially demonstrated at the 500 MWe scale at the Lagisza plant located in Bedzin, Poland. The CFB at the Lagisza plant has unique first-of-a-kind design features, such as vertical-tube supercritical steam technology and a lowtemperature flue-gas heat extraction that allows the plant to achieve high plant efficiencies of over 43% (net lower heating value). Another unusual feature for a coal power plant is that this plant meets all its atmospheric emission permit levels without any post-combustion de-NOx or de-SOx equipment such as selective catalytic reduction (SCR) or flue-gas desulphurization (FGD).CFB clean coal power technology is entering the utility power sector just in time to help deal with declining quality in internationally traded coals and to promote the large-scale use of economic, low-quality domestic fuels. Owing to the very attractive price discounts, growing supplies of low-quality Indonesian coals are outpacing the supply of high-quality Australian, Russian, and US coals. In Germany and Turkey, the use of domestic lignites for power production provides a secure and economic energy solution while creating domestic jobs.Conventional pulverized coal (PC) boilers will have trouble accepting these off-specification coals because of their narrow fuel specifications; they typically call for heating values above 5500 kcal/kg. This limitation is not an issue for CFB technology because of its ability to burn the worst and best of coals with heating values ranging from 3900 to 8000 kcal/kg.This paper provides an outlook for future coal supply, quality, and price, as well as a review of the technical and economic benefits of CFB technology firing low-quality fuels for utility power generation."

Jan 1, 2015

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By D. Toporov, R. Abraham

"Gasification is a process of thermal conversion of solid carbonaceous materials into a gaseous fuel called syngas. Coal gasification is an efficient technology for a range of systems for producing low-emission electricity and other high-value products such as chemicals, synthetic fuels, etc.The paper presents the High-Temperature Winkler (HTW) gasification process, which is designed to utilize low-rank feedstock such as coals with high ash content, lignite, biomass etc. The process is characterized by a bubbling fluidized bed, where coal devolatilization and partial oxidation and gasification of coal char and volatiles take place, and by a freeboard where partial combustion and gasification of coal char take place.The recent development of the high-pressure HTW process is reviewed. Gasification of low-rank, high-ash coals with respect to gasification temperatures, conversion rates, and syngas quality is also discussed. The main HTW design steps required for an industrial-scale design are presented. Special attention is given to the process modelling, including global thermodynamic calculation as well as detailed CFD-based simulation of a reacting fluidized bed. Three-dimensional numerical results of the HTW process are also provided and discussed."

Jan 1, 2015

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magnetohydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2015

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the openstopes. Little work has been done in the past to determine pillar strength and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to oversize pillars with consequential loss of ore or undersize pillars resulting in potential collapses or pillar bursts. This paper describes a back-analysis of pillar failures at Impala Platinum, just north of Rustenburg, and provides insights into pillar behaviour. Strength formulae are presented for Merensky Reef pillars at Impala. These formulae may be used cautiously on other platinum mines with similar geotechnical and geomechanical conditions.

Jan 1, 2008