Search Documents

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By B. P. Watson, D. P. Roberts, R. A. Lamos

The Upper Group 2 (UG2) chromitite reef is a shallow-dipping stratiform tabular orebody in the South African Bushveld Complex, which strikes for hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 500 m. Pillars are widely used to support the open stopes and bords. Little work has been done in the past to determine the strength of pillars on the UG2 Reef and design was done using formulae developed for other hard-rock mines. This has led to oversized pillars with consequent sterilization of ore. In this paper we describe a back-analysis of stable and failed UG2 pillars on the Bushveld platinum mines, and provides a strength formula for UG2 pillars. The formula may be used cautiously on all Bushveld platinum mines with similar geotechnical, geometrical, and geomechanical conditions to the pillars in the database.

Aug 1, 2021

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluent is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10 mg/[l] cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a preneutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40 g/[l] NaOH. A preneutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By Y. Makola, M. Kilumba, S. Mwaba, P. Ilunga, F. Banze, B. Nel, P. Kyoni, N. Mautsa, R. Nkomba, G. Ilu

Kamoto Copper Company is a copper cobalt mining company established in Lualaba Province of Democratic Republic of Congo under a Joint Venture between Glencore PLC and Gecamines (the state-owned mining company). Operations consist of underground and open pit mines, a concentrator producing sulfide concentrate and oxide ores milled slurry, and a hydrometallurgy plant producing copper cathode and cobalt hydroxides from concentrate and ores. The production capacity is 300 k/a of copper cathode and 35 kt/a of cobalt hydroxide. Since Q4 2020, the Luilu hydrometallurgy plant has experienced operational instabilities due to increase in proportion of dolomite in the ore mined and fed to the plant. This was diagnosed by the significant increase in calcium grade in ore and acid consumption, continuous foaming, and overflow of tanks with subsequent adverse impact on equipment availability due to corrosion caused by acidic spills, structure integrity, and safety concerns around the acidic slurry spills. Production was adversely impact due above equipment availability and often throughput restriction to mitigate the foaming and overflows. A high gangue-acid-consuming ore management programme was developed with the aim of mitigating these impacts. The programme included: (i) use of defoamer agent in leach to stop foaming and overflow, (ii) design of a mechanical solution to leach foaming and overflow, and (iii) froth flotation for copper and cobalt minerals separation from dolomite. Only option (i) is presented in this paper. Through laboratory testwork, pilot-plant testing, plant trial, and full plant implementation, Kamoto Copper successfully implemented a defoamer agent (Kemfoam X9980) dosing at leach, resulting in significant reduction in foaming and overflow of leach reactors and countercurrent decantation thickeners. The optimum defoamer dose rate obtained was 20 mg/L. Since then, the Luilu recovered its operational stability, the corrosion of critical equipment ceased, and availability improved as the acidic leach slurry spills ceased. The constraint on throughput due to leach foaming was addressed and the frequency of sliming events in the thickeners was significantly reduced as the foaming on the supernatant surface ceased, with subsequent significant reduction in interfacial crud in solvent extraction.

Jan 1, 2023

By R. K. W. Merkle, F. A. S. Reyneke, Z. Harris, P. W. J. Delport

The technological advancements in computing power in the last 30 years have enabled the practical visualization of complex geological environments in three-dimensional (3D) space. 3D models and their application in the mining industry are becoming increasingly important, for example, to identify future exploration areas and targets, for mineral assessment and evaluation, and prediction and planning of future drill-holes. However, acquiring borehole data is an expensive practice, with drilling programmes costing mining companies up to billions of dollars each year. Tighter financial constraints on exploration budgets result in more pressure being put on three-dimensional models to accurately identify future target areas. This article aims to evaluate the potential drilling success of simulated greenfield and brownfield exploration using a 3D geological model created of Leeuwpoort tin mine. These simulations investigate the probability of intersecting a mineralized zone of economic interest and evaluate how the probability is affected when the number of drill-holes and distance from a known intersection changes. Furthermore, these simulations attempt to obtain an indication for the minimum number of drill-holes required for a successful exploration campaign at the mine. The investigation also aims to establish a first-pass attempt towards developing a ‘favoured procedure’ for identifying potential exploration targets for tin deposits with geological and geochemical characteristics similar to Leeuwpoort. The results for the ‘favoured procedure’ established are statistically tested using the ‘bootstrapping’ method. By simulating various exploration scenarios, the study also emphasises the importance of predicting successful drilling, which aids in budgeting for drilling programmes as the minimum number of drillholes needed for a specific exploration project can be determined.

Feb 2, 2022

By P. A. Roberts

A modified in situ leaching method for extracting gold from oxidized gold ores using a non cyanide lixiviant is proposed. A non cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide bearing solutions into the subsurface. Oxidized gold ores are the initial focus because earlier research on the use of sodium thiosulphate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulphate breakdown. A reconnaissance research programme, involving ore characterization and hydrometallurgical testwork on samples from four Australian ore deposits and preliminary reactive transport modelling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulphate and ferric EDTA, and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples under anaerobic conditions. The ore characterization and reactive transport studies, suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Physical permeability enhancement could be achieved by blasting and/or hydraulic fracturing of the ore. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in place leaching? has been adopted for the proposed gold extraction system

Jan 1, 2009

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By G. P. O’Malley, A. N. Nikoloski

One of the most promising options for extraction of copper from low-grade chalcopyrite ores by heap leaching, however, chalcopyrite is refractory and suffers slow leaching kinetics and poor overall extraction due to formation of a passivation layer on the particles. The solution composition is believed to strongly affect the formation of this layer. This paper examines the effects of the major cationic species of Fe3+/2+, Mg2+, Cu2+, and Al3+ and the anionic SO42− species in acidic ferric sulfate media with a composition simulating recycle heap leach conditions. It was found that altering the sulfate, iron or aluminium concentration had significant effect on the copper extraction, the concentration of copper slightly influenced the extraction, and the amount of magnesium had no appreciable effect. Also, iron and aluminium caused a change in the sulfate concentration, and the sulfate ions had the greatest influence on the extraction of copper under recycle leach conditions

Jan 1, 2023

By B. Talbot

How this simple plant generates a large revenue stream. The concept behind the Tailings Scavenging Plant (TSP) is simple: it is a non-complicated modular plant which is designed to be more stable than upstream plants. This, plus the use of ?high energy?, enables the plant to recover any metal missed by the upstream operation. Impala Platinum?Mineral process started pilot plant exercises in June 2003. The pilot plant ran for one year before the capital for the full-scale plant was approved. This year was used to motivate, design and cost a full-scale plant. The metal produced during the pilot and feasibility study enabled this part of the project to run at a small profit. The scale-up to full-scale was relatively simple as the pilot plant had a capacity of 180 m3/hrand the full-scale plant was designed for a capacity of 550 m3/h. The design for the full scale plant was completed in May 2003, with ground breaking taking place on 19 May 2003. The construction phase of the project went well with the commissioning of the first two modules taking place on 22 October 2003. The remaining two modules were commissioned two weeks later. The plant was at full capacity by the 20 November 2003. A review of the plants performance for the first 5 production months is as follows: the plant has required only a few minor modifications and additions, it has run well in excess of 95%availability with no major wear apparent. In addition to this, the plant has produced 3 times the metal forecast.

Jan 1, 2004

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

A high volume of slimes which are separated out during the mining of heavy mineral sands has a high environmental impact and results in great capital as well as operational expenses. The presence of clay minerals drastically increases the slimes volume that needs to be catered for due to its low settling capability as well as swelling characteristics. By adding coagulants in the form of cations and organics, one can improve the settling rate of the minerals as well as the degree of solid bed compaction. The addition of flocculant, which is currently used in industry to improve settling rate, is detrimental to solid bed compaction. By combining the cations and flocculant one can dramatically improve the solid bed compaction. This combination is, however, detrimental to the settling rate of kaolinite-rich slimes but improves the settling rate of smectite-rich slimes. Organics can also be used to produce a clear supernatant and improve the settling rate.

Jan 1, 2010

By E. Öğretici, S. Kahraman

The indirect estimation of intact rock properties is particularly useful for preliminary investigations in engineering projects. In this paper we examine the usability of electrical resistivity, a nondestructive measurement, for the prediction of physical and mechanical rock characteristics. Physico-mechanical tests (uniaxial compression, Brazilian tensile, density, and porosity tests) and electrical resistivity measurements were performed on specimens of 36 rock types. Before the resistivity tests, the specimens were completely saturated with saline solution. Evaluation of the test results showed that there are medium or strong correlations between resistivity and rock properties. There are also strong or stronger correlations between the two parameters for the rock classes. The regression equations developed were statistically tested, and their validity was confirmed. The results were also compared with previous studies. The conclusion is that electrical resistivity measurement can be used for reliably estimating physical and mechanical rock characteristics.

Aug 8, 2024

By P. K. Hofmeyr

Traditional fire assay dates back over 3000 years and has changed very little over that time. The only improvement is to replace the gravimetric finish with dissolution of the Precious Metal bead followed by AA or ICP analysis of the solution. The newly developed FIP A (Fast In-line Fire Assay) method allows full automation of the fire assay process from sample preparation to spark analysis of the Pb button. This results in fully quantitative analyses for Pt, Pd, Rh, Ru, lr, Au and Ag in typically less than an hour after a sample is entered into the system. Detection limits are theoretically Pt 0.08 ppm, Pd 0.002 ppm, Rh 0.002 ppm, Au 0.08 ppm and Ag 0.002 ppm but in practice the lower measurable limits are about double these figures. Few opportunities have been available to present data obtained using the FIFA system as all FIFA laboratories have been in the domain of a Pt mining company which prefers to keep all Pt analytical matters confidential. However, IMP has recently participated in the round robin exercise to establish recommended values for a new series of Merensky Reef and UO-2 Layer reference materials produced by African Mineral Standards. The precision of the results was excellent being on average Pt 2.05%, Pd 1.25%, Rh 4.08% and Ru 4.94% being expressed as Relative Standard Deviation. The excellent precision is a reflection of the efficient collection of POEs in the Pb buttons and the homogeneity of the Pb buttons. However, the accuracy was not as good. The poorer accuracy is interpreted as the calibration of the spectrometer not being as good as desired due to the difficulty in acquiring a suitable range of standards with reliable recommended values for the PGEs. The most recent spectrometer was calibrated with the greatest care and produced slightly better results for Pt, Pd and Rh and slightly worse for Ru.

Jan 1, 2014

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By B. Maybee, J. Venter, J. Wesseloo

The selection of open-pit slope angles involves high-value decisions with small changes in slope angle, often representing significant changes in net present value. The existing methods used to define design acceptance criteria have evolved from factor of safety to probability of failure (P[F]) to risk consequence to risk frontiers, which represents current state of the art. Current design acceptance measures are based on references to published tables representing the experience and judgement of their authors, who did not specify the purpose of the measures contained therein. As the purpose of the published design acceptance criteria is not specified (i.e., definite stability, marginal stability, optimization, etc.), such tables cannot be used to achieve optimum slope angles that maximize profitability. This paper develops a design acceptance criterion that maximizes profitability by defining a formulation for optimum risk that balances expected risk and reward. The model developed is titled the Mining Risk Model (MRM), and is applied to open-pit slope angle selection through an equation for optimum probability of downside (P[D]O) that balances the upside or opportunity, the P[F], and the downside impact. This formulation for optimum risk is unique, as many authors have presented objective functions for their risk models that can be optimized, but none of the sources reviewed contained a formulation for optimum risk. The MRM is sufficiently flexible to allow the design performance measure that drives P[F], and hence P[D]O, to be selected based on the intended goal. Furthermore, the essential information that must be known to quantify optimum risk is defined. This allows users to determine what information to collect for optimum risk decisions. A further benefit of the MRM is that slope angle decisions and pit shells can be ranked to select the best option, and a threshold is provided that separates acceptable from unacceptable decisions. Finally, the workflow and information required to determine optimum risk are presented.

Sep 9, 2024

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007