Search Documents

By M. Grozdanovic, D. Marjanovic, M. Ilic

We present a framework for solving the problem of functional compatibility between process control equipment in control centres at underground mines and operator capabilities. The equipment incorporates displays of current ventilation, gas, and fire hazard data, status of alarm and early warning systems, a voice communication subsystem, and facilities for recording and printing ofdata and reports. The layout of the existing control panel is compared with a recommended design. The basic principles of ergonomic design and arrangement of the controls and indicators, as well as ease of use, type of operations carried out with these controls, and operators’ viewing angles are discussed. The objective is to improve the usability of control panels, display boards, and graphic screens so as to enhance the functioning of control centres and optimize control of technological processes in coal mines.

Jun 10, 2024

By B. Hart, B. K. Gorain, A. Chattopadhyay, S. Dimovc

This paper presents a detailed and systematic approach to metallurgy diagnostics using an integrated novel gold deportment technique for complex copper-gold and refractory gold ore bodies. This uantitative gold deportment for these complex ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Gold mostly occurs as "invisible gold" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulphides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Studies were initiated on various complex ore deposits and also on samples representing various process streams. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A systematic and holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies. Keywords: Integrated gold deportment, complex copper-gold ores, double refractory gold ores, carbonaceous matter, diagnostic metallurgy, preg-robbed surface gold

Jan 1, 2020

By T. C. Huber

The southern African region has a high concentration of mineral resources and supplies much of the world?s platinum demand. As a result, the international community watches South Africa to understand the impact of supply on global markets. An analysis of supply certainty and risk plays a key role in the future of growing demand in various sectors. The southern African platinum industry experienced substantial growth in the early part of the 21st century, resulting in bullish forecasts for growth during the period of 2000?2006. However, southern African platinum producers saw a significant drop in production over the following three years as a result of many dynamic factors in operations and the global economy. Between 2006 and 2009 there was a million-ounce shortfall between forecast and actual production. This was raised as a concern at the Fourth International Platinum Conference in 2010 by Stephen Forrest during his keynote address, specifically regarding the lack of understanding in the market of the causes of this shortfall and any action that was being taken to address them. This paper reviews publicly available information in the media and corporate reports and communications for the period January 2006 to December 2009. In addition, several interviews were held with key stakeholders in the industry to provide further perspective. The paper then highlights the main reasons that are reported to have affected the loss in production over the period and discusses the possible implications of the information that the mining industry does and does not disclose regarding platinum supply.

Jan 1, 2012

By H. Möller, M. Tshibalanganda, C. Taute, A. du Plessis, M. Leary

Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood.

Apr 1, 2021

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

Mr D. Twigg graduated in Metallurgy at the Sheffield Polytechnic, and later obtained a Master of Science degree at the University of Bradford. Mr I.D. Matthews matriculated at Roosevelt High School and joined the No. 1 Parachute Battalion in 1968. He worked in Zimbabwe for 31 years in geological prospecting, civil engineering, and open-pit mining.

Jan 1, 1985

By V. van der Merwe, C. W. Siyasiya

"A petrochemical company experiences premature thermal fatigue failure of the casting moulds used in catalyst production. The aim of the project was to find an alternative alloy that would outperform the current low-alloy cast steel used for the moulds. Based on their thermo-fatigue properties, 3CR12 ferritic stainless steel and H11 tool steel were chosen for testing and comparison with the currently used BS3100 B7 cast steel. Samples of each material were subjected to temperature cycling in a Gleeble 1500TM thermo-mechanical processing simulator, followed by surface analyses. The main parameters derived from the test work were the total true strain, the hot strength of the materials, and the number of cycles to failure. Additionally, the coefficient of thermal expansion for each material was measured using a Bähr dilatometer. H11 tool steel yielded the best performance by way of having the fewest surface cracks, the lowest total true strain per cycle, the most cycles to failure, the highest hot strength, and the lowest coefficient of thermal expansion.IntroductionThe Catalyst Manufacturing Plant (CMP) is a dusty environment with temperatures higher than ambient. Molten mill scale (magnetite, Fe3O4) is tapped from the electric arc furnace into the casting moulds at temperatures close to 1600°C. After 10 seconds the magnetite is quenched with a water spray for 50 seconds to a minimum temperature of 400°C. Sometimes there is residual water in the pans from the cooling fog process (water sprays) in the empty mould. In a typical plant, the factory produces 40–44 batches a day containing between 150–300 moulds, depending on the time required for the specific batch (Buchholz, 2014). The typical batch in the CMP usually weighs about 6 t. The thickness of the tap, speed of the casting belt, and tilting angle all affect the number of moulds per batch.One of the main problems faced during the molten mill scale casting is the premature failure of the casting moulds. Cracks initiate on the surface of the mould, which is in contact with the hot catalyst, and propagate into the interior of the mould. Cracks are generally concentrated in the middle area of the mould where the catalyst makes first contact with the mould, and which experiences the highest temperature fluctuations. This suggests that the cracks are caused by thermal fatigue during the casting process."

Jan 1, 2016

By K. B. Le Bron, T. van Aard

The empirical pillar strength formulae have been widely, and in most cases successfully, applied to design underground pillars for mines in the Bushveld Igneous Complex (BIC). This paper presents the case for combining the empirical method with numerical modelling when it comes to crush pillar stability analyses. The benefits include an understanding of potential failure mechanisms, which may then be accounted for in the designs. In addition, the impact of weak layers, such as shear zones, the impact of the dip of the orebody, differences in layouts, such as holing widths and the presence of advanced strike gulleys (ASGs) immediately adjacent to the crush pillars, and stress regime (k-ratio) may be studied using numerical modelling, as it is not accounted for in the empirical method.

Mar 5, 2025

By B. Dias, P. C. Schutte

Work-related musculoskeletal disorders (WMSDs) affect the wellbeing of workers and result in poor quality work, lower work performance and decreased motivation. In contrast to ‘occupational’ diseases where there is a direct cause-and-effect relationship between hazard and disease (e.g., asbestos and asbestosis, lead and lead poisoning), ‘work-related’ diseases are multifactorial, where the work environment and the type of work that is performed contribute significantly to musculoskeletal disorders. WMSD is the term used to describe disorders and diseases of the musculoskeletal system (i.e. muscles, joints, ligaments, tendons and nerves). WMSDs are by definition a work-related phenomenon. The literature shows inarguably that certain jobs and certain work-related factors are associated with a significant risk of contracting a WMSD. It is assumed that repeated movements and postures, static work, continuous loading of the tissue structures or lack of recovery time, trigger or cause a pathological process that then manifests itself as a WMSD. This paper looks at the prevalence of the WMSD condition at three mines in South Africa: a coal, a gold and a platinum mine. Predisposing factors that include work factors, presentation of symptoms and psychological factors will be discussed in the paper.

Jan 1, 2003

By M. Kumral, Y. A. Sari

Underground mining operations tend to have higher operating costs than surface mines. When metal prices decrease, profitability is jeopardized due to the high costs. Therefore, mining management harnesses new practices that increase operational efficiency. One way to manage this challenge is to invest in new mine planning practices. Stope layout optimization as a part of underground mine planning aims to identify a portion of the orebody in the form of production volumes (stopes) to maximize profit under roadway and stope dimension constraints. In this paper we propose a novel approach based on identifying ore-rich areas of the deposit and prioritizing their extraction through an iterative heuristic clustering approach. The proposed approach is compared with and validated by an exact method through a small mining example. The heuristics produced nearly identical results in a very short time. Finally, a case study was carried out using a larger data-set. The cluster-based iterative approach generated nearoptimal stope layouts in a computationally effective manner.

Mar 1, 2021

By L. Scott, M. A. Goncalves

Effective communication is a sought-after non-technical skill in the health, safety, and environmental (HSE) function and is fundamental in achieving an organization’s safety objectives. While different channels are used to communicate HSE matters, many organizations employ posters, videos, and/ or signs containing images to convey information. Communication through signage and graphical hazard symbols has been regulated in standards, but vast sections of HSE communication are bespoke communications and exist outside the sphere of standards. Effective HSE communication through images requires an understanding of the organizational culture in which the images will be used, as well as an understanding of the semiotics of the images themselves. Creative interpretation within HSE communication can create situations where the message that was received is not the message that was intended, leading to confusion and misinterpretation. This paper is aimed at elucidating the semiotics of South African HSE visual content. It was found that the indexical mode of images was most preferred in visual communication, and text-only designs the least preferred. Senders and receivers of messages differ in their opinions on the complexity of HSE communication.

Feb 2, 2021

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By J. Maritz, K. de Beer, S. M. Buthelezi

The economic upheaval of COVID-19 forced companies to invest in emerging technologies to aid recovery. One such technology is extended reality, which is becoming a mature and innovative tool. Early adopters are seeing significant benefits in learning, training, immersive data visualization, and remote assistance. In South Africa, the mining industry is increasingly interested in using extended reality to optimize and innovate operations. The Minerals Council of South Africa's July 2021 report highlighted the potential of extended reality's to achieve zero-harm production and modernize the industry. However, the extent of extended reality adoption in mining remains unclear due to limited information on its usage. This study addressed this gap by distributing an online survey to assess awareness, knowledge, and current uses of extended reality in South Africa’s mining sector. The results indicated that virtual and augmented reality had the highest levels of awareness and usage, primarily for learning and training. Mixed reality, however, had the lowest awareness and knowledge levels. In terms of applications, visualization and remote assistance had the least use cases. These findings highlight that the South African mining industry is deficient in its understanding and use of extended reality technologies. Without better awareness and application, the South African industry risks missing out on the full benefits of extended reality. The study underlines the need for the South African mining industry to improve its outlook on extended reality technologies to fully leverage their potential applications and benefits.

Jul 10, 2024

By J. P. T. Kapusta

"The copper smelting industry faces increasingly stringent environmental regulations and must continue driving innovation to reduce energy usage in its production chain. With the coming of age of ‘bottom-blowing’ copper technologies in China over the last decade, much renewed attention has been brought to tuyere bath smelting for clean copper-making. Since bottom-blowing sonic injection was originally developed and implemented in steelmaking in the 1970s and lead smelting in the 1990s, the time seems appropriate to revisit the sonic injection concepts and dispel some myths. After reviewing the trends in the copper industry and providing a brief historical context of research and development related to sonic injection, the author presents a comparison of the main submerged tuyere bath smelting technologies, namely the Noranda Reactor (NR), the Teniente Converter (TC), and the Chinese Bottom-Blowing Smelting Furnace (SKS/BBS) for copper, and the Queneau-Schuhmann-Lurgi Reactor (QSL) for lead. The core of this article, however, consists of a brief description of the fundamental theories for sonic injection (jetting regime) and ‘sonic flow mapping’ to illustrate the relationship between the minimum tuyere back-pressure required to achieve sonic flow and the tuyere internal diameter. The article also offers a comparison between side- and bottom-blowing in jetting regime before concluding with the author’s vision of the new trend in submerged tuyere bath smelting. IntroductionIn the last decade, developments in the copper smelting industry have been driven by two key concepts: (1) increasing cleaner smelting capacity to meet the world’s growing copper demand, as illustrated in Figure 1, and (2) increasing process off-gas capture to comply with more stringent environmental regulations and abide by a corporate social responsibility ethic of a clean work environment (for smelter employees) and clean air (for families living around smelters). The copper smelting industry has also faced some major challenges in the last few decades, including (1) low treatment and refining charges (TC/RC or processing fees) impacting custom smelters, (2) lower concentrate quality and grades with higher levels of impurities (e.g. As and Hg), (3) higher processing and transportation costs due to the rising cost of energy, (4) restrictions in process intensification (tonnage oxygen usage) due to furnace integrity limits, and (5) scarcity of educated and trained personnel due to fewer metallurgists graduating from pyrometallurgical school programmes combined with a high retirement rate of skilled workers."

Nov 1, 2018

By A. Pareek, V. S. Masampally, V. Runkana

Mineral processing plants, in general, consist of comminution and separation circuits. Rougher flotation is considered as the heart of the separation circuit with concentrate grade and mineral recovery being the key productivity and quality parameters that affect the downstream operations and profitability. Online prediction of these parameters can help improve process performance in real-time. Past efforts to predict flotation cell performance have focused on building physics-based or machinelearning (ML) based models. Although physics-based models are popular in process design applications, ML models are more appropriate for online monitoring, control and optimisation due to their lower computational requirements. Deep learning (DL) is gaining prominence nowadays for application in industrial operations where a large amount of data is available. We have developed a DL model based on long short-term memory (LSTM) neural networks to forecast the two key performance indicators (KPIs), namely, mineral recovery and concentrate grade in a mineral processing plant. Rougher feed characteristics such as mineral grade and particle size distribution, upstream measurable disturbances such as throughput of the comminution circuit and pulp density, and control variables such as aeration rate, pH, and collector addition rate are considered as explanatory variables to train the model. The model was tested with data from an industrial mineral processing plant. For real-time dynamic predictions, the trained model appropriately accounts for mismatch in measurement frequency of real-time process data and off-line laboratory analysis data. Such a time series model can be used as a state observer in model predictive control techniques for optimal control of unit operations in a mineral processing plant. Keywords: Mineral processing, flotation, time-series, dynamic modelling, deep learning

Jan 1, 2020

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2012

This report describes the investigational work on the development of a fire-assay method capable of concentrating, in a button of nickel sulphide, all six of the platinum-group metals present in samples of ores, concentrates, and mattes. In the method adopted, the sample is fused with a mixture of sodium carbonate, sodium tetraborate, nickel carbonate, and sulphur. The nickel sulphide formed during fusion collects the noble metals and carries them to the bottom of the crucible. The nickel sulphide button is dissolved, and the noble metals are isolated and determined. The coefficients of variation range between 1,0 and 4,9 per cent for the various platinum-group metals when they are present in concentrations between 0,3 and 75 p.p.m.

Oct 15, 1971

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By F. Dong, F. Yang, J. Wang, Z. Wang, D. Mingxia

Antimony oxide ores are important antimony resources, but their recovery is still a problem. In this paper, the adsorption behaviour and mechanism of dodecamine and quaternary ammonium salt on the surface of cervantite and quartz were investigated. The flotation behaviour of cervantite and quartz using quaternary ammonium salts and dodecylamine as collectors was studied by single mineral flotation experiments. The adsorbed amount was measured and infrared spectroscopy was used to study the ability of several cationic collectors to float cervantite and quartz. The results show that quaternary ammonium salts can simultaneously float the cervantite and quartz. It is difficult to achieve separation of the two minerals using quaternary ammonium salts as collectors. At pH>10, dodecylamine can float quartz but not cervantite, which can achieve reverse flotation separation of the two minerals. The difference between the abilities of quaternary ammonium salts and dodecylamine to float cervantite and quartz lies in the different ionisation properties of the two reagents. Quaternary ammonium salt is a strong electrolyte that is completely ionised in the pulp and exists mainly in the form of quaternary ammonium ions. Dodecylamine is a weak electrolyte and predominantly forms molecules under alkaline conditions. Keywords: Cervantite, quartz, dodecylamine, quaternary ammonium salts, flotation

Jan 1, 2020

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014