Search Documents

By R. V. Ramani, V. T. Burgos, J. A. McClay

The systems contributing to the cost analysis, and the flow of data input and output related to these systems, are brought into focus in Figure 6. The various sub-systems of the Master Design Simulator provide the raw operating data basic to the cost model which, operating independently, accumulates the raw input, assigns costs to this data by standard or modified costing procedures, manipulates the costs into standard formats and outputs the data for managerial evaluation. Cost Modeling Direct costing methods are not complex in the sense that elemen¬tary arithmetic is employed using the same basic relations for each cost category. The basic cost model relations described above are illustrated in Figure 7. The greatest difficulty encountered in the transition from a dy¬namic systems simulation model to a costing model is the time frame of the input and output data. Dynamic simulation models utilize a small time increment, on the order of seconds or fractions of seconds, to analyze system operations and interactions. On the other hand, for cost computation and reporting, the smallest relevant time unit is the shift, with reporting periods expanding to days, weeks, months, and years. Complications arise in the accumulation of data for the various report periods due to the use of the Gregorian calendar by modern so¬ciety. The potential for simulation for the life of the mine, possibly in excess of 50 years, increases the complexity of the costing process

Jan 1, 1975

By Jack C. White

The purpose of this Bureau of Mines work was to develop information useful in improving copper recovery during copper milling operations. Eleven copper mill tailings from the Western United States were subjected to froth flotation and cyanide leaching to provide an experimental basis for comparing their beneficiation response. Recoveries in flotation concentrates made from mill tailings ranged from 65 to 15 percent, at copper grades of 13 and 2.2 percent, respectively. Liberated copper sulfide minerals present in two samples were readily recovered by laboratory froth flotation. Nine of the samples were less amenable to froth flotation because of physical locking between copper sulfide minerals and gangue. Correlations among tailings indicated that recovery of sulfide copper by flotation was directly related to the sulfide copper content. Empirical equations derived from flotation data provided average values for unrecoverable copper and for recovery efficiency. Flotation response of copper mill tailings may be predicted from the equations. Data from cyanide leaching provides an equation describing the limiting high values for removal of copper by this method.

Jan 1, 1974

"The dust/lung research of the Center has several long-range objectives:* better methods for the early diagnosis of coal workers' pneumoconiosis (CWP);* methods to modify the disease process;* tests to identify toxic products; and* tests to identify individuals with heightened susceptibility to pneumoconiosis.A major immediate objective is to define the mechanism of dust-induced lung disease. This means determining:* dust characteristics that are important in causing lung diseases;* important interactions between dust and lungs; and* earliest detectable stages of the disease.Several of the Center's projects involve exposing lung cells in culture (in vitro) or animal lungs (in vivo) to samples of the suite of characterized mineral dusts described earlier. The responses of the lung cells or tissues to the dusts are being studied in order to better understand how inhaled dusts cause lung disease.One project is studying the effect of dust exposure on the production of mucus by rat tracheal explants in vitro. Mucus is a major factor in clearing inorganic dusts from the lung. Results thus far have shown that exposure of tracheal cultures to coal dust caused a decrease in micin production in comparison to parallel cultures without dust. To examine the effect of in vivo coal dust exposure, rats were maintained in an inhalation chamber for two weeks, and control rats were in an identical, but dust-free chamber. Tracheal explants results indicate that the effect of in vivo dust exposure is similar to that noted in the in vitro experiments.Pulmonary alveolar macrophages (PAMs) are a key component of the lung's response to inhaled particulates, and they play several important roles in pulmonary inflammatory and repair processes. PAMs are the cells that actually ingest dust particles. Other studies have shown that they play a critical role in the development of silicosis and asbestosis. The Center is studying the effect of dust exposure on the release of oxygen free radicals (superoxide) by PAMs. Intercellular production of superoxide occurs when PAMs phagocytize particles, such as inhaled bacteria, and is an essential mechanism by which PAMs kill ingested, bacteria. A number of complex physiological events occur during this process which are not clearly understood. It is thought that PAMs containing indigestible materials, such as mineral dusts, overproduce superoxide, or inappropriately release it into the surrounding tissues. If true, this would cause toxicity to surrounding lung cells by peroxidation of the lipids in the cell membranes. In vitro exposure of PAMs to low or high doses of kaolin is inert. Preliminary studies indicate that coating the quartz particles with a surfactant reduces toxicity."

Nov 1, 1988

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

By Howard E. Parkinson

An environment monitoring and communication system has been installed in the Bruceton Mine, and research is under way to improve mine safety. Standard day-to-day mine communications are available, along with additional systems installed to permit experimentation with wireless radio, through-the-earth phones, along-the-roof paging, and mine face machinery communications. Research is continuing and the essential concepts for a dependable whole mine communication system, providing simple environment monitoring, improved day-to-day communications and post-disaster communications, will be demonstrated in a larger mine with about 900 feet of overburden.

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

By D. A. Stanley

The Bureau of Mines has developed a simple titration technique for determining the points of zero charge (PZC) on minerals. The technique consists of titrating a mineral slurry with the potassium salt of polyvinyl sulfuric acid (PVSK) in the presence of an indicatory dye and a positively charged polymer. Values obtained by this simple method are in good agreement with values found in the literature.

Jan 1, 1982

The Bureau of Mines has developed test procedures and criteria for evaluating explosive reactivity of explosive-contaminated solid waste substances generated by U.S. Army ammunition plants. These substances are produced as explosive-contaminated sludge from wastewater treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations (CFR), part 261.23(a)(6) and (7). These are the Bureau's gap and internal ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This report also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

By Karl R. Becker

Detonators representing a sampling of various domestic commercial delay detonators were fired at various direct-current (dc) firing levels. Results of firings using well-below-recommended firing levels showed marked increases in delay times above the nominal values. There was also a marked increase in variation, to the extent that out-of-sequence firings would be essentially assured in any typical blasting round at these low firing levels. Within the range of recommended levels the effects of current increases were not considered to be of great importance relative to other overriding effects, such as the significant difference noted in average values of detonators from different lots having the same nominal delay. This effect, when combined with the normal variation noted among members from the same lot, would cause out-of-sequence firings with detonators from a neighboring delay period. Where comparisons with results from another study were possible, it was found that both studies observed quite similar variations in delay times about the average values, and a lower probability of out-of-sequence firings for the shorter delay period groups. The criterion of the previous study for assessing the likelihood of observing out-of-sequence firings, when applied to the Bureau of Mines data, properly identified two neighboring delay period groups where out-of-sequence firings would occur.

Jan 1, 1981

Dec 1, 2007

Tables

Jan 1, 1992

By Kathleen M. Kowalski-Trakofler

This paper discusses human judgment and decision making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behaviour in underground mine fires. The authors assert that stress is one of the factors that decision makers must contend with in most life-or-death situations. They suggest that a better understanding of individual judgment and decision making activities whilst under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers and policymakers.

Jan 1, 2003

By Lloyd A. Morley, Alan M. Christman

This report was prepared by the Department of Mineral Engineering, The Pennsylvania State University, University Park, Pennsylvania under USBM Grant Number G0155102. The grant was initiated under the Metal and Nonmetal Health and Safety Research Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Mr. Roger L. King acting as the Technical Project Officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period February 1, 1975 to July 31, 1976. This report was submitted by the authors on August 31, 1976.

Jan 1, 1976

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

By Gerrit V. R. Goodman, Fred N. Kissell, Charles D. Taylor

In This Chapter [Methane emission peaks Exhaust line curtain or duct The spray fan system Dust scrubbers with blowing ventilation Dust scrubbers with exhaust ventilation The ventilation of abnormally gassy faces Methane detection at continuous miner faces Ventilation and methane detection at bolter faces and Reducing frictional ignitions] This chapter gives guidelines for preventing methane gas explosions at continuous miner sections in coal mines, both at continuous miners and at roof bolters. The need to control peak methane emissions is particularly stressed. Emphasis is also placed on ventilation principles, monitoring for gas, and reducing frictional ignitions. METHANE EMISSION PEAKS Methane emission from the coal at continuous miner faces varies considerably. Plotted on a chart, methane emissions consist of a series of peaks and valleys corresponding to the cutting cycle of the mining machine, with the methane concentration spiking as the machine cuts into the coal (Figure 3–1) [Kissell et al. 1974]. These methane peaks can be substantial. For this reason, efforts to safely dilute the methane must focus on the level of the [ ]

Jan 6, 2006

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967