Search Documents

By Jerry E. Olson

In 1986, at the request Of the Bureau of Land Management, the U.S. Bureau of Mines studied the central portion, encompassing 20,727 acres of the 32,261-acre Badlands Wilderness Study Area (OR-005-021) in order to evaluate its identified mineral resources. The study area is located in Crook and Deschutes Counties, OR, about 12 miles east from Bend. No mineral resources were identified. The area studied is underlain by Tertiary and Quaternary basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, or mineralized areas occur within or near the study area, but some sand and gravel has been removed from alluvial deposits at the east and west sides of the area. Slab lava of marketable grade and quantity was not found in the study area. None of the study area is of current interest for geothermal resources, but the eastern third of the wilderness study area is leased (1984) for oil and gas.

Jan 1, 1987

Significantly reduce respirable dust exposures of longwall shearer operators when cutting out at the headgate. Approach As a result of Bureau research, a ventilation curtain is recommended to be mounted between the stage loader and the coal rib to more effectively prevent the ventilation air from blowing across the shearer drum as it cuts out at the headgate. Some mine operators already employ this method of reducing dust, but a vast majority do not. How It Works One source of extreme concentrations of respirable dust for longwall shearer operators is the shearer headgate drum as it cuts through into the headgate entry. As the drum cuts into the entry, it is exposed to the primary ventilation airstream. The high velocity air passes through and over the rotating drum, picking up large quantities of dust.

Jan 1, 1982

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

By R. L. Wise

Heat content studies were conducted on burned shale, spent shale, and three grades of raw oil shale from the Green River Formation. Corrections were made for product enthalpies. The results were compared with previous work, indicating good agreement below retorting temperatures, but some differences at retorting temperatures. A general equation was developed relating heat content to oil-shale grade and temperature.

Jan 1, 1971

By John L. Reuss

A laboratory study was conducted by the Bureau of Mines to investigate the technical feasibility of decomposing hydrous magnesium chlorides by using a steam pyrohydrolysis technique. This procedure consisted of injecting steam into the atmosphere of a decomposition furnace containing samples of hydrous magnesium chloride and determining the rate of hydrolysis by measuring the rate of chloride evolution. The variables investigated were temperature, amount of water vapor in the decomposition atmosphere, and hydration stage of magnesium chloride. The application of steam was shown to accelerate both the rate and completeness of magnesium chloride decomposition reactions. For example, when magnesium chloride hexahydrate is exposed to a furnace temperature of 600' C in an air atmosphere for 20 minutes, the decomposition is 37 percent. Under identical conditions in a steam atmosphere, the decomposition is in excess of 70 percent. The magnesium oxide produced by the steam pyrohydrolysis of magnesium chloride dihydrate at 800° C contained 98 percent magnesium oxide. Based on magnesium oxide composition, this is equivalent to that of burned magnesite produced at temperatures in excess of 1,300° C. To demonstrate the quality of the product on a practical basis, metal reduction tests have shown it to be equivalent to reagent-grade magnesium oxide as a carbothermic reduction feed material.

Jan 1, 1974

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

By Thomas J. Peters

The U.S. Bureau of Mines studied the 3,500-acre Winegar Hole study area, Idaho, a legislatively proposed (101st U.s. Congress) addition to the Winegar Hole Wilderness, Wyo.; it adjoins the western boundary of the Wilderness at the Idaho-Wyoming border, about 15 m; east of Ashton, Idaho. The study was part of an Idaho Land Assessment Program to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The study area is an east-west elongated, wooded plateau south of Falls River. Although the area is covered with surficial glacial deposits, it is probably underlain by volcanic flows; light-colored and mafic flow rock were noted in sparse outcrop. No mines, prospects, mineralized areas, or mineral resources were found in the study area during a literature and field search. The only nearby prospects include geothermal and rock aggregate (volcanic cinder) sites, and several placer claims. Although the Winegar Hole study area lies within a region of potential geothermal resources, no evidence of geothermal activity was observed. Rock in the area does not split into flat slabs, which could be useful as dimension stone, and would require crushing to be used 8S aggregate. Alluvium (placer) samples contain less than SO.01 per cubic yard gold (at a $350 per oz price); alluvial deposits are too small to contain gold resources.

Jan 1, 1992

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

By M. Viswanathan, M. J. Jorgensen, N. K. Kittusamy

Operating heavy construction equipment is often associated with elevated rates of low back discomfort (LBD). However, there have been few formal studies that dealt with evaluating controls that can reduce the LBD among these workers. The objective of this study was to determine the effectiveness of using a continuous passive lumbar motion system (CPLMS) in reducing low back discomfort among operators of heavy earthmoving equipment. The CPLMS is an additional seat support that has a lumbar support bladder and a pump to provide cyclic inflation and deflation. Two groups of operators were identified as potential subjects for this intervention study, the intervention group with a mean age of 41.2 years and experience of 9.7 years used the CPLMS, and the control group with a mean age of 37.5 years and experience of 7.6 years did not use the CPLMS. Body part discomfort surveys were collected from both groups. In addition, the intervention group completed a CPLMS preference survey. The body part discomfort survey was collected up to eight days at three different times of the day. Results from the body part discomfort survey showed a decreasing trend the longer the CPLMS was used, for both the upper and low back region. A decreasing trend for the low back was also found comparing morning to evening discomfort scores across the days when using the CPLMS. When compared to their regular seat, 54% of the operators felt very comfortable in using the CPLMS, 36% of them wanted one for their equipment, and 54% showed interest in experimenting with the CPLMS for a longer time period. Results from this study indicate that the use of a CPLMS can effectively reduce the low back discomfort experienced by operators of heavy construction equipment.

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

Develop a new method for coal mint pillar stability evaluation and design based on pillar load measurements. Approach A novel approach to chain pillar stability evaluation and design for longwall coal mining panels has been developed by the Bureau of Mines. The evaluation approach uses an INTEGRITY FACTOR as the criterion for stability. Hydraulic borehole pressure cells developed by the Bureau are used to measure stresses in a pillar for stability evaluation. The results are used to improve the pillar design.

Jan 1, 1989

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

By Hillary W. St. Clair

The effective coefficient for rate of reduction of a sample of granular iron ore may be determined by passing the reducing gas through a bed of the are at constant flow rate and periodically analyzing the effluent gas, The method of analyzing the data is based on a mathematical model that takes into account the variation in composition of the gas and solids with time and position in the bed. A method is described for determining the value of the rate coefficient that gives best agreement between the observed and calculated analyses of the effluent gas.

Jan 1, 1967