Search Documents

By G. W. Jones, R. E. Kennedy

"INTRODUCTION Information relative to the ignition temperatures of acetylene and acetylene-air mixtures has become of particular interest recently due to a number of explosions that have occurred in 500-pound, double-rated, medium-pressure acetylene generators in shipyards on the West coast. Various suggestions have been made as to the causes of these explosions prominent among which has been that air finds its way into the acetylene generators during abnormal operation or that air remains in the carbide hopper of the generator following the purging and charging operations.This raises the question as to how and to what extent the presence of small percentages of air in acetylene affects the ease of ignition of such mixtures at the various operating pressures of the acetylene generators. The range of operating pressures in the 500-pound, double-rated generators involved in the explosions may vary from below atmospheric to 15 pounds gage.The present report gives the results of an investigation made to determine the effects of pressure on the ignition temperature of pure acetylene and of acetylene containing varying percentages of air:EXPERIMENTAL Apparatus A preliminary investigation showed that a heated quartz surface gave lower ignition temperatures than other material tested.A ""hot-spot"" method of ignition was found desirable in the case of the acetylene mixtures since the violence of the explosions was reduced by keeping most of the test mixtures at room temperature. Explosive violence was reduced further by using an ignition tube 17 mm. or less in diameter."

Mar 1, 1945

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Among the hazards that may attend the use of Diesel engines in mines, tunnels, or other underground operations the presence of harmful or objectionable constituents in the exhaust gas must receive due consideration to prevent the formation of unsafe or unhealthful working environments in these places. Previous reports of this series have presented discussions of the composition of exhaust gas from engines in proper mechanical condition, 6/ the effect of adding some of the exhaust gas to the intake air of the engine, 7/ the effect of operation in atmospheres containing natural gas, 8/ and the effect on exhaust-gas composition of conditions that influence the characteristics of fuel injection in Diesel engines. In all these studies the properties of the fuels used were in general conformity with specifications usually recommended by the manufacturers of Diesel engines. In evaluating the physiological significance of the various components of the exhaust in these experiments, the toxic or objectionable gases determined were carbon monoxide, carbon dioxide, oxides of nitrogen, and aldehydes. Because of the low sulfur content of' these fuels, compounds such as sulfur dioxide and sulfur trioxide were not determined, although in discussion of the test results attention was directed to the fact that if fuels of higher sulfur content were used, the concentration of such compounds in the exhaust would become a significant factor in establishing the quantity of ventilating air required to furnish satisfactory dilut1on of the exhaust gas in underground working places."

Jun 1, 1943

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence coefficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculation methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By N. S. Dalal, X. Shi

"It has been recently suggested that the exceptionally high antitumor and antibacterial activity of natural fredericamycin A (FMA) is related to its ability to spontaneously generate the superoxide anion (02-) and hydroxyl (""OH) radicals in aerobic solutions [Hilton, B. D., Misra, R., & Zweier, J. L. (1986) Biochemistry 25, 5533]. With a view to understand the mechanistic details, attempts were made to reproduce earlier electron spin resonance (ESR) evidence for the oxygenated free radical formation in well-aerated solutions of natural FMA in dimethyl sulfoxide and dilute H 20 2• Little or no evidence was obtained for the formation of the 0 2- and methoxy (""OCH3) radicals, while the detected formation of the 'OH and methyl ('CH3) radicals was attributable largely to mechanisms not involving FMA. These results thus reopen the T question regarding the mechanism of its exceptionally high tumoricidal-bacteriocidal activity. This paper reports on an electron spin resonance (ESR) investigation of the formation of oxygenated free radicals in solutions of natural fredericamycin A (abbreviated as FMA) which has recently been reported to be a highly potent anti¬tumor antibiotic (Pandey et al., 1981; Warnick-Pickle et al., 1981). The impetus for this undertaking was provided by recent reports (Hilton et al., 1986; Stinson, 1986) suggesting that the strong tumoricidal activity with high therapeutic—toxic index of FMA was related to its ability for the spontaneous generation of superoxide anion (02-) and hydroxyl (OH) radicals. For example, the suggested mechanism for the formation of 02- by FMA was (Hilton et al., 1986)FMA-OH + O2 FMA-O + H+ + 02-Here FMA—OH is simply the FMA molecule emphasizing the —OH moiety which becomes FMA-O, the free radical rep¬resenting the oxidized form of the drug. While some other highly effective anticancer drugs in current clinical application, such as bleomycin, are also thought to exert their antitumor effects via the formation of reactive drug-based or oxygenated free radicals (Carmichael et al., 1985; Gianni et al., 1983), FMA was considered unique in that only in this case the free radical formation was thought to be spontaneous, rather than through a metal- or an enzyme-activated process (Hilton et al., 1986; Stinson, 1986). Thus it was suggested (Hilton et al., 1986; Stinson, 1986) that FMA could be the forerunner of a new class of anticancer drugs. However, we noted that while the hypothesis seemed plausible, the reported ESR spectral evidence appeared to be ambiguous. Because of the high significance of the earlier conclusions (Stinson, 1986), we undertook a systematic ESR study of the radical formation in FMA solutions, and as discussed below, our conclusions disagree with those reported earlier."

Jan 1, 1989

By E. J. Gleim

The construction of explosion-proof electric mine equipment for operation in gassy coal mines of the United States was begun as early as 1903. In 1.906, similar equipment with special protective devices was built for export. An investigation of explosion-proof motors was conducted by the United States Bureau of Mines during 1910 and 1911. In other words, this was among the first efforts of the Bureau directed toward the saving of life and property subsequent to its establishment by act of Congress in 1910. In these early motors, those with special devices for relief of explosion pressures predominated. At that time it was generally considered that, by providing for pressure relief, the enclosures could be made lighter in weight because of the lower explosion pressures developed within.

Jan 1, 1954

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

By R. V. Ramani, S. Shankar

"A convective dispersion model has been utilized to calculate the real-time airborne dust concentration in mine airways using re-entrainment as the only source term for airborne dust. It incorporates two important sources of re-entrainment in mines -- air velocity and movement of objects. The model has a sink term accounting for the deposition of particles along the airway. The model is solved using a finite difference scheme which is coded for computer. The computer model outputs airborne respirable and total dust concentrations along the airway as a function of time. The real-time and average gravimetric concentrations from several in-mine experiments were compared with the results from the simulation of the experimental conditions. This model can be used for estimating airborne dust entrainment due to air velocity, equipment movement, and persons walking. INTRODUCTIONEdwards and Ford (1988) developed a model for coal dust explosion suppression and utilized a predetermined value of threshold velocity for flowing air to pick up dust from floor. Depending on the strength of the removal forces, re-entrainment can increase the airborne dust concentration in mine airways. The most prevalent forces causing re-entrainment in mine airways are the drag and lift forces due to flowing air, and removal forces due to the movement of persons and vehicles. Shankar and Ramani (1991) have investigated the unique characteristics of the re-entrainment phenomenon in mine airways. Experiments on re-entrainment of coal dust particles were conducted in mine airways, and in a wind tunnel (Shankar and Ramani, 1994a, and 1994b). The results from the two experimental studies were found to compare well (Shankar and Ramani, 1995). There is no reported model to determine the airborne dust concentrations due to airflow or persons walking under conditions existing in mines. The present study is a part of a continuing research project in the Generic Mineral Technology Center for Respirable Dust on the spatial and temporal behavior of airborne dust in mine airways (Ramani, 1983)."

Dec 1, 1996

[ ]

Jan 1, 2012

By J. W. Thompson

"The ordinance of March 27, 1919, contains provisions relative to the exploration for, Ind the exploitations of bauxite in the Colony of Surinam in Dutch Guiana.Permission to explore is limited to: Netherlanders; inhabitants of the Netherlands; inhabitants of Surinam; companies established in Netherlands, and companies established in Surinam.Holders of concessions for the exploitation of bauxite are limited to companies established in the Netherlands, or in Surinam, and these must reside in the Colony or must be represented the constantly.A permission or concession lapses: (a) when the holder ceases to have the required qualifications; (b) on the death of the holder where the assigns fail within one year to prove the required qualifications.Any dispute concerning the required qualifications must be decided by the Judge in the manner to be regulated by colonial ordinance.The Governor may, after consultation with the Privy-Council reserve tracts of land for the exploration and exploitation of Bauxite, either for the Government directly, or for concession under special provisions. These provisions shall be fixed by virtue of the colonial ordinances.Application for permission to explore shall be made in accordance with existing laws. Simultaneous applications, those made on the same day, must be decided by drawing lots; but an application for the concession for exploitation has preference ovor that for permission for exploration. On notice of objection to the drawing of lots, the Governor may in his discretion, declare the drawing null and void and order a re-drawing."

May 1, 1920

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By John Gross

The modern practice of grinding ores so that often 80 per cent or more of the product is finer than 200 mesh makes it desirable to supplement sieve sizing so as to extend considerably the range of sizing. Moreover, the fact that the material finer than sieve size represents the major part of the work done in grinding emphasizes thick need in can investigation of crushing efficiency. A method based on the settling rate of particles in grater appeared to be most practical for sizing; finely ground ores. There are two possible methods of utilizing this principle: one based on free settling or sedimentation; and the other on separation by means of a rising; current of water, or elutriation. In sedimentation, mechanical entanglement causes material at the start to settle in a mass, and this persists throughout. As this feature is largely eliminated by elutriation, which permits a comparatively clean separation of the various sizes, the elutriation method was adopted.

Jan 1, 1929

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain event a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain ev';ent a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

By H. H. Schrenk

[A calorimetric method3/ for the determination of benzene in amounts as low as 0.001 m has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel from the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations.]

Jan 1, 1935

By Maria I. De Rosa

Table 37 and figure 13 show the number of fires and fire injuries for surface stone mines by state during 1990-2001. Table 37 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 96 fires occurred in 31 states and 1 fire occurred in Puerto Rico. Sixty-eight of the fires caused 67 injuries and 1 fatality (including 6 fires and 5 injuries involving contractors). The yearly average was eight fires and 5.6 injuries. The Ewhr value was 689 x 106 hr (Irr = 0.02), and the LWD value was 7,399. Indiana had the most fires (eight fires and four injuries), followed by Georgia (seven fires and seven injuries) and Pennsylvania (seven fires and five injuries). Of these states, Georgia had the highest injury risk rate value (Irr = 0.058). Table 38, partly illustrated in figure 14, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries show an increase during the second period followed by a decrease during most of the remaining periods. Employees' working hours increased during most of the periods. The In values follow patterns similar to those shown by the injury values. Tables 39-44 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 15 shows the major variables related to fires for 1990-2001. Table 45 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Lucia Kuizon

Results of the U.S. Bureau of Mines' survey of mineral resources in the Cuyama RARE II study area indicate there is no potential for metallic minerals and low potential for the development of gypsum resources. There are no producing or developing mines within the study area. The Santa Barbara Canyon Prospect contains 30,000 tons (27,000 t) of subeconmic gyspum resources, the Wagon Road Prospect 276,000 tons (250,000 t), and the Brush Fence Canyon 61,000 tons (55,000 t). Most of the resource in the Brush Fence Canyon Prospect is outside the area. Gypsum was not observed at the Cuyama River deposit. Present gypsum and gypsite requirements are being met by larger deposits closer to major markets. INTRODUCTION Location (USGS) Present and Previous Studies (to be combined with USGS section) The Bureau of Mines reviewed literature and mining claim records for the study area. A field examination of known mineral properties was made in October 1980; it included mapping and sampling of prospects to evaluate the economic potential of mineral resources.

Jan 1, 1981