Search Documents

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By F. K. OVITZ

In its endeavor to promote a more efficient use of coal the Bureau of Mines, in cooperation with the Illinois State geological survey and the University of Illinois, has undertaken an investigation of the coking of Illinois coals. The investigation was started by collecting from various sources the data regarding experiments already made by others; these data have been compiled and are presented herein. The present methods of using coal seem wasteful. When coal is burned in furnaces for the generation of steam, only the heat gener- ated by the fuel is utilized; possible by-products are not only lost but frequently are the source of the smoke nuisance. The volatile matter containing the tar and heavy hydrocarbon gases is difficult to burn completely in many furnaces, and its decomposition produces black smoke. When coal is coked in a by-product oven, the volatile matter is no longer a nuisance but, on the contrary, is the source of many by-products, including benzol, toluol, gas, tar, ammonia, and cyano- gen, all of which increase the value that may be obtained from coal. The coke that remains after the volatile matter has been driven off is a valuable fuel that can be used for almost all purposes for which bituminous coal can be used, and it is necessary for some metallurgical work. It has about the same heating value as anthracite coal. Because of its cleanness and its burning without smoke, it is well suited for domestic heating and the generation of steam in plants where smokelessness is demanded. The use of coke for these pur- poses would do much to eliminate smoke in cities. The best grades are regarded as essential in many metallurgical processes for reduc- ing ores to their metals. By-product coking in the United States during the past three years has increased greatly. When the ovens now in course of construction are completed, the total capacity of by-product ovens will be more than double what it was in 1913. This increase has led to a search for coals other than those now known to be available for use in by- product ovens. Tests with coals from the southern part of Illinois have indicated that coke from Illinois coal unmixed with other coals can be used for fuel purposes and that coke from mixtures of Illinois coal with low-volatile coking coal might be suitable for some metal- lurgical work. In the tests the yield of ammonia was larger than is obtained from Eastern coal. Evidently the development of methods by which good coke can be made from Illinois coals and the by-products recovered is a matter of high importance. Any investigation that will indicate how, by proper treatment, these coals can be made available to supply the market for coke and gas in the Middle West will increase efficiency in their use, and will aid in conserving the country's supply of high-grade coking coal.

Jan 1, 1917

This chapter focuses on smoke as it relates to escape from underground mine fires. Among the topics discussed are the measurement of visibility in smoke; smoke-related hazards such as the production of CO, hydrochloric acid (HCI), or other byproducts of combustion; and miners' personal experiences while escaping through smoke. Smoke Measurement and Visibility In general, smoke consists of hundreds of thousands of very small particles. These particles have some "size," usually expressed in terms of their diameters, and they have some concentrations, usually expressed either in the number of these particles per unit volume or the total mass of the particles per unit volume. Humans cannot see individual smoke particles because they are too small. Similarly, "umber concentrations" and "mass concentrations" of smoke particles do not have much meaning to people unless they are trained technically. Still, individuals know that they can see smoke, independent of all the technical jargon used to describe it. Also, they know that when the smoke level gets too high, it is no longer visible. In fact, nothing is visible because the smoke absorbs all of the light in its surroundings. The eye is only sensitive to light in the wavelength region from about 400 nm to about 700 nm. The maximum sensitivity of the human eye is to light that has a wavelength of about 555 nm. It is important to know how the eye responds to light because if its response is known, it is possible to use a light detector that has almost the same response as the eye. Such a detector can then be used to quantify the visible characteristics of smoke because it responds in the same manner as the human eye. Smoke is visible because it either scatters or attenuates (diminishes) light. In some instances, smoke is visible because the smoke particles reflect light which is then detected by the eye. The eye actually "sees" an intensity of light that has been reflected from a cloud of smoke particles. Imagine shining a flashlight into a cloud of smoke. Someone off to the side can actually "see" the beam of light as it traverses the smoke cloud. This is called scattering. Smoke is also visible be¬cause it attenuates light. Imagine having someone shine a flashlight into your eyes. As smoke begins to build up along the beam of the flashlight, the light begins to dim. The smoke is visible because it is now reducing the intensity of light that falls upon the eye. As the smoke level increases, it is said to obscure our visibility. When the beam is no longer visible, the smoke obscuration is said to be 100%. In other words, none of the light energy from the flashlight makes its way through the cloud of smoke. Another way of saying that the obscuration is 100% is to say that the transmission of light through the cloud is zero.

Jan 1, 2000

By Gerald J. Joy, Paul J. Middendorf

This study examines the patterns and trends in noise exposure documented in data collected by Mine Safety and Health Administration inspectors at U.S. coal mines from 1987 through 2004. During this period, MSHA issued a new regulation on occupational noise exposure that changed the regulatory requirements and enforcement policies. The data were examined to identify potential impacts from these changes. The overall annual median noise dose declined 67% for surface coal mining and 24% for underground coal mining, and the reduction in each group accelerated after promulgation of the new noise rule. However, not all mining occupations experienced a decrease. The exposure reduction was accompanied by an increase of shift length as represented by dosimeter sample duration. For coal miners exposed above the permissible exposure level, use of hearing protection devices increased from 61% to 89% during this period. Participation of miners exposed at or above the action level in hearing conservation programs rapidly reached 86% following the effective date of the noise rule. Based on inspection data, the occupational noise regulation appears to be having a strong positive impact on hearing conservation by reducing exposures and increasing the use of hearing protection devices and medical surveillance. However the increase in shift duration and resulting reduction in recovery time may mitigate the gains somewhat.

By S. R. B. Cooke, J. Bruce Clemmer, Will H. Cognill, F. D. DeVaney

"INTRODUCTION The domestic production of potash has made rapid strides in the past 4 years. In 1929 the United States produced 109,820 tons of potash-bearing material, equivalent to 61,590 tons of pure potash (K20). In 1933 to this had increased to 331,110 tons, containing 143,378 tons of potash, due chiefly to the development of the potash deposits near Carlsbad, N. Mex. The potash ores of that district occur at a depth of about 1,000 feet and as mined consist of a mixture known as sylvinite containing about 40 parts of sylvite (KC1) and 60 parts of halite (NaCl). By careful mining the extraneous material does not amount to more than 2 or 3 per cent. Such ore was used in the experimental work here reported.The usual chemical method for the recovery of potash from sylvinite, while efficient in the production of pure potassium chloride, requires,expensive equipment and is costly to operate. It occurred to the Bureau of Mines that ore-dressing methods, which have been applied to other nonmetallic minerals, might be adapted for the production of a grade of potash suitable for the fertilizer industry. After preliminary study by the Bureau of Mines showed that ore-dressing treatment was possible the investigation was extended under a cooperative agreement between the U.S. Bureau of Mines, the Potash Company of America, and the Missouri School of Mines and Metallurgy, Rolla, Mo.ACKNOWLEDGMENTSAcknowledgment is here given for valuable assistance in the laboratory of R. G. O'Meara, assistant metallurgist. U.S. Bureau of Mines, Tuscaloosa, Ala. who was on detail at the Rolla station during the early work; by E. W. Gieseke and Albert Ollar, temporarily employed by the Potash Company of America; and to N. H. Lenz, an engineer temporarily assigned to the station."

Feb 1, 1935

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By P. T. Brooks

Electrochemical machining sludge, a troublesome fluid waste product, was dewatered on a bench-scale basis by three alternative methods tested by the Federal Bureau of Mines. These methods would enable recycling 89 percent or more of the liquid content of the sludge and allow the dewatered solids to be dumped as landfill or processed further to recover contained nickel. Dewatering by vacuum precoat filtration was estimated to be the least expensive. Based on treating 20,000 gallons per day of sludge, precoat filtration costs were estimated as totaling 1.96 cents per gallon of sludge. Two options of an alternative method, comprised of acidification, reprecipitation, thickening, and filtration, were estimated to cost either 3.41 or 3.60 cents per gallon of sludge.

Jan 1, 1976

By M. R. Geer, H. F. Yancey

"INTRODUCTION The increased use of coal as pulverized fuel has focused attention on the grindability of coal and on the necessity of evaluating this property by a method suitable for use in the usual coal-testing laboratory. Without some knowledge of how various coals behave in the grinding operation, that is, how their use affects mill capacity and power requirements, the selection of coals for pulverized-fuel plants cannot be made on the same critical basis used in selecting coals for other types of burning equipment. The grindability of a coal, serves principally as an indication of the mill capacity attainable in grinding it - not as a direct index of the total cost of grinding. Although the grindability of coal may play a minor role at some plants, it is a decidedly important factor where pulverizer capacity limits the ability to carry high loads.Purpose Standardized tests for determining the grindability of coal are relatively new, so that the information now available on the grindability of various coals is limited in comparison, for example, with that available on proximate analyses. Published information is restricted to determinations on many important Eastern coals by the Fuel Engineering Co. of New York, 4/ a bulletin giving the results of numerous tests by the Babcock and Wilcox Co. 5/, and a comprehensive report on. Alabama coals by the Bureau of Mines. 6/This report presents the results of grindability tests of 34 samples of coals from Illinois, Kentucky, Pennsylvania, Utah, Virginia, Washington, West Virginia, and British Columbia at the Northwest Experiment Station of the Bureau of Mines, Seattle, Wash., in cooperation with the College of Mines of the University of Washington. In the future, as the laboratories of the Bureau make grindalility tests of other coals, additional reports will be issued."

Jul 1, 1938

By D. N. Nilsen

The Bureau of Mines is developing a method to recover Ni, Co, and Cu from laterites containing less than 1.2 pct Ni and 0.25 pct Co. The method consists of the following basic unit operations: (1) reduction roasting, (2) leaching, (3) solvent extraction, and (4) electrowinning. The method reflects three Bureau of Mines objectives: (1) recovery of critical minerals that are domestically in short supply from low-grade domestic laterites, (2) lower processing energy requirements, and (3) solution recycling. This report deals with the extraction of cobalt and the preparation of a suitable cobalt electrolyte by solvent extraction from liquor produced by this method. Nickel and copper are coextracted with LIX64N from an ammoniacal ammonium sulfate leach liquor containing about 1.00 g/l Ni, 0.30 g/l Co, 0.03 g/l Cu, and 0.02 g/l Zn. Cobalt (III) in the nickel-copper barren raffinate is reduced to cobalt (II) with cobalt metal. Reduction of cobalt (III) to cobalt (II) greatly aids subsequent extraction. Commercially available XI-51 extracts about 94 pct of the cobalt from the treated raffinate in one stage in a laboratory mixer-settler continuous circuit. Ammonia loaded on the solvent is removed in two washing steps. About 94 pct of the cobalt then is stripped from the XI-51 in one stage with spent cobalt electrolyte containing about 77 g/l Co and 18 g/l sulfuric acid (H2S04), Electrolytes containing less H2S04 also may be used. Preliminary data indicate that coextracted zinc may be removed from pregnant cobalt eletrolyte containing 3 g/l or less H2S04 with di-(2 ethylhexyl) phosphoric acid (D2EHPA).

Jan 1, 1980

Provide a means for continuous measurement and display of respirable dust concentrations in a mine so that when high dust levels occur, timely, corrective measures can be taken. Approach Develop a personal dust monitor that (1) is small and light enough to be worn by a miner, (2) has the capability to continuously measure the respirable fraction of coal dust, (3) will display the respirable dust concentration in mg/m3, and (4) can store the average respirable dust concentration and sampling time of several sampling shifts for later play-back. How It Works The personal dust monitor (PDM-1) uses light scattering and convection air currents to sample the respirable fraction of coal dust. Convective air currents cause dust laden air to pass through an open-celled sampling chamber (light sensing chamber). A near infrared light emitting diode (LED) located in the PDM-1 emits pulses of light. The pulsed light passes through a focusing lens and glass window into the sampling chamber. The light is then reflected, scattered, and refracted by the airborne dust particles. Light scattered within the angles of 450 to 900 (the angles within which the intensity of the scattered light is most closely related to respirable-size dust particles) passes through another window and is focused on a light detector. The light detector signal is amplified and presented as analog output voltage for conventional recording. This signal is also converted to a digital signal which the microprocessor uses with its crystal clock to calculate the 10-second average dust concentration, the shift average concentration, the time-weighted average concentration, and the elapsed sampling time. The microprocessor also stores dust concentrations of the seven most recent sampling periods, controls the operation of the LED and detector, and operates the liquid crystal display (LCD).

Jan 1, 1983

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

By H. L. Burmeister

These properties were examined by a Bureau of Mines engineer in 1949. During 1950, these mines were studied by the Bureau to determine the possibility of increasing the production and augmenting the supply of fluorspar. As a result of this study, it was decided to core-drill the Knox-Yingling vein to test the continuation of fluorspar to a greater depth than that reached by mine workings. It also was desired to relate the present deposit with the Rosiclare formation. Development work by the Bureau of Mines was performed from February to May inclusive in 1951. Four diamond-drill holes aggregating 2,733 feet were drilled in the hanging wall of the vein.

Jan 1, 1952

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By R. E. Head, Virgil Miller

"Under existing conditions in the treatment of oxidized lead ores containing small quantities of molybdenum no provision is made for the recovery of the molybdenum. Considerable quantities of this important element are lost in the slags of the lead smelters and constitute an economic waste. There is little or no probability that slag dumps containing molybdenum in small quantities could be economically treated for the recovery of the element, and steps for the prevention of waste in this respect must be taken prior to smelter treatment.Wulfenite, lead molybdate (PbMo04), and molybdite, molybdic ocher (Mo03), are the molybdenum minerals most abundantly found in deposits of oxidized lead ores. Wulfenite contains 39.3 per cent molybdenum trioxide and 60.7 per cent lead oxide; molybdite contains 66.7 per cent molybdenum and 33.3 per cent oxygen. Plumbojarosite, argentojarosite, cerussite, and occasionally anglesite are commonly associated with wulfenite ores, and the oxidized iron content is usually fairly high.The recent discovery and development of a body of wulfenite ore in the Star district near Milford led to a cursory microscopic examination of samples of the ore, followed by a few preliminary tests which had for their object the separation and recovery of the lead and molybdenum in separate products.The microscopic examination showed that the samples used in the work were composed of wulfenite, plumbojarosite, and a small quantity of cerussite, and indicated that the iron content was quite high. The ore was porous and yellowish-brown; crystals of wulfenite appeared to be quite uniformly distributed through it, and this mineral and plumbojarosite (Pb0.3Fe203.4S03.6H20) apparently accounted for the major part of the lead content, although lead"

Sep 1, 1928

The extrapolation of results from reconstructed laboratory soil columns to field conditions is difficult because of the limitations of laboratory experiments. Permeability and elution tests performed in the laboratory differed from the natural state in that the soil was sieved through 1/4 inch screen to remove large stones and roots, its density was controlled by tamping the soil into two-inch I.D. tubes instead of normal weathering, and water and latex were applied with a constant head of liquid. Tube wall effects are important in interpreting data. Conversely, interpretation of field results were confounded by non-homogeneities within the sample tested, a soil profile with gradation of permeability and density with depth, and uncontrolled weather conditions and seasonal changes that affected the results. Nevertheless, both laboratory and field tests showed that a specific latex did perform as a soil sealant. In view of these facts a soil box experiment was designed to overcome some of the disadvantages associated with the small laboratory soil columns and the field experiments. Two wood soil boxes 5 ft x 5 ft x 5 ft were built in the greenhouse at the Uniroyal Research Center. They were lined with plastic PVC sheeting provided with tubes every six inches of depth on one side of each box to measure water removal rates under saturated conditions. Tensiometer gauges were placed at depths of 6, 12, 18, 24, 36 and 48 inches and Bouyoucos blocs and resistance thermometers were positioned at 6, 24 and 48 inch depths. Each box was filled with a uniform sub-soil obtained from Ogdensburg, N. J. The texture of this soil was determined to be a sandy loam by the ASTM Hydrometer method, as shown below: [ ] The boxes were thoroughly wetted by sprinkling to abet settling and allowed to dry by draining to check seepage ports and functioning of tensiometers.

Jan 1, 1972

By Webster S. Anderson

The design, development, and testing of hydraulic props to provide a lightweight, high strength, recoverable unit is described. Modifications in design incorporating threaded components resulted in the development of a lightweight hydraulic prop fabricated from aluminum alloy tubing. This new design facilitates interchange and replacement of component parts, and the physical properties of the material are not changed as they are when welding is required. The new prop is 65,000 pounds and has a maximum load capacity of a lower weight-to-load capacity ratio than the hydraulic props now available.

Jan 1, 1967

By G. A. Burrell, G. W. Jones

As a part of the work which the Bureau of Mines carried out in 1916 and 1917 pertaining to the compressibility of natural gas , it became necessary to de termine the pressure -volume relations of several of the paraffin hydrocarbons of which natural gas is composed . Results of the work on natural gas were published in Technical papers 131 (Burrell , G.A. , and Robertson , I.W. , The compressibility of natural gas to high pressure , Bureau of Mines Tech . Paper 131 , 1916 , 12 pp. ) and 158 (Burrell , G.A. , and Robertson , I.W. , Compressibility of natural gas and its constituents with analyses of natural gas from 31 cities in the United States , Bureau of Mines Tech . Paper 158 , 1917 , 12 pp . ) , and curves were given of pressure volume deviations of the gases , methane , ethane , propane , and carbon dioxide at high pressures . original experimental data on these gases , however , were not published . The In view of many inquiries which the Bureau has received with reference to the original data on the se gases , and the importance of the pressure -volume relations from which it is possible to calculate the deviation of any natural gas who se composition is known , the original data as determined by Burrell and Robertson are pre sented below .

Aug 1, 1921

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977