Search Documents

By Nicholas Kyriazi

Significant portions of the present Federal regulations for certification of closed-circuit breathing apparatus (42 CFR 84) are not quantitative. The human-subject testing portion of the regulations specifies activities rather than metabolic work rates; however, heavy human subjects have higher oxygen consumption, CO2 production, and ventilation rates than lighter human subjects performing the same activities. This means that apparatus certified using different human subjects have effectively passed different tests. In addition, apparatus performance is monitored only during selected intervals of testing, and always during rest, rather than during the entire performance period. Further, testing is arbitrarily terminated at specific rated durations, leaving unknown the performance during the remaining duration. Duration itself is misleading to users who believe that the apparatus will last a certain time no matter how much they weigh or how hard they work. The actual duration obtained from an apparatus, however, is highly variable, being inversely proportional to the work rate at which it is used. In this report, recommendations are made to (1) replace the present regulations for certification of closed-circuit breathing apparatus with quantitative tests specifying metabolic work rate rather than activity,(2) continuously monitor relevant physiological stressors, (3) continue testing until exhaustion of the oxygen source, and (4) classify closed-circuit breathing apparatus by quantity of usable oxygen, i.e., capacity, rather than by duration. Physiology-based stressor levels are suggested as well.

Jan 1, 1999

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

[ ]

Jan 1, 2011

By McHenry Mosier

The Bell mine operated by the Warner Co. at Bellefonte, Pa., has an annual production of about 600,000 short tons of high-grade limestone. Since 1924, shrinkage stoping has been the mining method. Horizontal, long-hole diamond-drilling for production in stopes was started with one machine in July 1946. It is now standard practice. The burden on the holes is 10 feet. Diamond bits are noncoring EX-size in both concave and pilot types. The two types have little difference in drilling speed at the Bell mine. The diamond drills are mounted on 3-inch single-screw columns. Diamond drilling shows a marked increase in efficiency at the Bell mine, compared to percussion drilling, with respect to tons broken per drill shift, tons broken per foot of hole, and tons broken per pound of explosive. The advantages of diamond-drilling blast-holes also include (a) improved safety, greater footage per drill shift, (c) better frag- mentation of the broken, stone, and (d) reduction in amount of barring down required in stopes because the working places are limited to slots which have a relatively small area.

Feb 1, 1948

By J. A. Woolf, E. S. Leaver

"So much has been written on the ore genesis of the Comstock Lode that it is sufficient here to describe the original ores as consisting chiefly of quartz and some calcite. In places .a considerable amount of pyrite appears. There are also minor amounts of galena, chalcopyrite, and sphalerite. The chief silver minerals are argentite, stephanite, and polybasite. Most of the gold is native.A composite analysis of the ore; obtained by averaging the results from the early workings of several mines, is shown in Table 1.The history of the milling of Comstock ores from the Sixties to date would call for a review of the development of precious-metal metallurgy. However, a brief outline of the methods employed will give a better basis for studying the difficulties that are to be expected in the final retreatment of the remaining residues.In the earliest days amalgamation was accepted as the main recovery method. The large tonnage of good-grade ore from the Comstock Lode attracted the best metal¬lurgical talent of the time, and developed there the highest skill in the art of amalgamation, including the auxiliary chemical preparation of the ores and the mechanical operation. In this work 0.5 to 6.0 pounds of mercury was used per ton of ore. The mercury loss probably averaged about 2.5 pounds per ton of ore treated.The better grade of tailings from the ores milled were impounded, often near the works. In many cases the same tailings were reworked several times before they entered the main outflow waste stream that had its course down Seven Mile Canyon to the Carson River. Following the water course down the canyon the tailings were re-impounded, and, as metallurgy advanced, new plants were erected to again re-treat them. The most successful of these plants used forms of amalgamation, chlorination, and cyanide methods of recovery. To the tailings from the re-treatment plants, smaller tonnages of untreated tailings produced by milling lower-grade ore are continually added.Along the stream bed down the canyon a series of blanket runways were constructed, and each was independently operated for years by one or more men. All, or the heavier portion of the stream flow was run over the blankets; in this way much of the heavier concentrate, mostly sulphides and mercury products, was reclaimed.All of the residues finally entered the run-off flow along with the sewage from Virginia City and waste from the gas works, saw mills, and stables. As the accumulation along the bed of the Carson River became a nuisance, the lighter and better grade of tailings was impounded on the banks of the river. This accounts for the large dumps locally known as ""Douglas tailings."""

Jul 1, 1928

By John D. Sullivan, Edward P. Barrett

The experimental work on the utilization of tin-plate scrap at the North- west experiment station of the U. S. Pireau of Mines in cooperation with College of Mines, University of Washington, necessitated the selection of a simple method for the determination of tin in the iron produced. Some of the standard methods for the determination of tin which were tried are given below: 1. Dissolving in acids and precipitating the tin as sulphide, igniting and weighing as Sn02. 2. Dissolving in aciis, reducing with nickel, cooling in an atmosphere of carbon dioxide, end titrating with standari iodine solution. 3. Dissolving in acids, precipitating the tin as sulphide, dissolving this sulphide in H3 and H2S04, heating until fumes of 503 are evolved, reducing with nickel or sheet lead, cooling in an atmosphere of carbon dioxide, ani titrating with a standard iodine solution.

Mar 1, 1923

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

By C. Travis Anderson

 The general conclusion of earlier investigators was that the action of sulfur dioxide on manganese oxides of Cuyuna ores was not sufficiently pre- ferential to be attractive as the basis for a commercial process. Bradley4/ and his coworkers discarded it for leaching with boiling ammonium sulfate solution, and Sweet5/ used a baking operation to render the iron insoluble. These results were confirmed by the early tests in the present investigation, which were made on brown ores (Sagamore), using acid additions, because at that time the Technologic Committee on Manganese held the opinion that these ores constituted the major available reserve in the Cuyuna district. However, when it appeared that the black ores, or the formation in which they occur, were a possible source of a large tonnage of manganese, the use of sulfur dioxide and sulfuric acid leaching was again reviewed, and a satis- factorily preferential action on the manganese was found. It was originally thought that the use of sulfuric acid ahead of, or at least with, the sulfur dioxide simplified the process, particularly by preventing formation of dithionates. Removal of the phosphorus from the solution by neutralization with lime or fresh ore was suggested. The tests recorded in this report indicate that it is not practicable to use enough acid to prevent formation of dithionate and that the value of excess sulfuric acid is doubtful, particularly in regard to satisfactory manganese:phosphorus and manganese:iron ratios.

Jul 1, 1942

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center&apos;s Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By N. A. Caspero, W. E. Eckard, W. T. Wertman

A thermal oil-recovery experiment was conducted in the Venango First sand, Goodwill Hill oilfield, Warren County, Pa., about 10 miles northeast of Titusville. The Quaker State Oil Refining Corp., Bradford, Pa., performed the experiment with assistance from Sinclair Research, Inc., Tulsa, Okla., and the Federal Bureau of Mines. The Goodwill Hill field was discovered in 1885. Primary-production oper- ations continued until 1930 when an air-gas injection project, which is still in operation, was started. At the location of the combustion experiment, the reservoir is 400 feet deep and 30 feet thick, with wide permeability and porosity variations. The crude oil is typical Pennsylvania Grade paraffin- base oil with a gravity of 43.9° API and a viscosity of 4.55 cp at 60° F. The well pattern for the experiment consisted of 5 producing wells, enclosing an area of 1.28 acres, and a central ignition-injection well. An air-natural gas mixture was ignited in the ignition well on July 29, 1961. Ignition was followed by injection of air and natural gas at various rates. The experiment was suspended January 5, 1962, when it became evident that economic oil production could not be achieved. There was no conclusive evidence that self-sustained combustion was achieved or that combustion increased oil and water production. A slight increase in liquid production was attributed to stripping action caused by the air-injection rates, which were higher than those normally used during air-gas injection.

Dec 1, 1963

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By Lloyd A. Morley, Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in/which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-roof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges. Explosion-proof enclosure techniques have been utilized in U.S.

Jan 1, 1974

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M&apos;) and the ratio of the maximum air velocity to the minimum air velocity (V&apos;) as measured in the cyclone entrance channel.

Jan 1, 1972

By B. T. Brady

Laboratory measurements by the Bureau of Mines indicate that failure in dry rock specimens measuring approximately 13 cm in length is preceded by tilt anomalies lasting a few milliseconds. The tilt behavior is qualitatively similar to that reported to precede earthquakes. Test results suggest that the time duration of this tilt anomaly for laboratory specimens of this length is independent of rock type, in agreement with theoretical predictions and other experimental data on rock failures including earthquakes.

Jan 1, 1975

By W. Wallace, T. Ong, M. Gautam, M. Keane, S. Xing, J. Harrison

"Diesel exhaust soots were assayed in the Ames Salmonella typhimurium histidine reversion assay system using TA 98, the soots being applied as the following preparations: dispersion in dipaimitoyl glycerophosphoryl choline (DPL), dispersion in dipalmitoyl phosphatidylethanolamine (DPP!), and dispersion in dipalmitoyl phosphatidic acid (DPPA) in physiological saline, and in physiological saline without added surfactant. The extracts of soots by dichloromethane / dimethylsulfoxide (DCM/BHSO) were also assayed. Studies were performed both with and without :IQ microsomal activation of the soot preparations. The DPP! and DPPA surfactants were chosen as phospholiridz with two palmitic acid moieties esterified to a glycerol as is the case with DPL, but with hydrophilic groups having different electrophilic characters. The soots, without S9 activation, showed mutegenic activity when extracted in the conventional procedure with DCM/DMSO. The mutagenic activity of soots dispersed in DPL was quantitatively comparable to, and in some cases greater than, the activity expressed by an equal mass of soot extracted by DCM/DMSO. Soots in other surfactantpreparations, DPP! and DPPA, also expressed positive mutagenic activity. Praincubation with S9 microsomal enzyme fraction reduced the activity of solvent extracted soots, and greatly diminished the activity of DPL dispersed soots. Initial sister chromatid exchange (SCE) assays using the Chinese hamster V79 cell line indicated DPL dispersed soot also can cause SCR in mammalian cells. Results thus far suggest that surfactant suspended or ""solubilized"" respirable soot particles could provide a mechanism for transport and expression of mutagens in the lung."

Jan 1, 1989

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, C. J. Malanga

There is evidence to suggest that cell injury induced in alveolar macrophages (AM) following phagocytic activation by silica particles may be mediated through changes in intracellular free calcium [Ca 2+}. However, the mechanism of silicainduced cytotoxicity relative to [Ca2+], overloading is not yet clear. To provide a better insight into this mechanism, isolated rat AMs were exposed to varying concentrations of crystalline silica (particle size< 5 µm in diameter) and the fluctuation in their [Ca2+]; and cell integrity were quantitatively monitored with the fluorescent calcium probe, Fura-2 AM, and the membrane integrity indicator, propidium iodide (Pl). Results from this study indicate that silica can rapidly increase [Ca2+]; in a dose-dependent manner with a characteristic transient calcium rise at low doses (<0.1 mg/ml) and an elevated and sustained rise at high doses (>0.1 mg/ml). Depletion of extracellular calcium [Ca 2+]0 markedly inhibited the [Ca2+]; rise (˜90%), suggesting that Ca2+ influx from extracellular source is a major mechanism for silica-induced [Ca2+]; rise. When used at low doses but sufficient to cause a transient [Ca2+]; rise, silica did not cause significant increase in cellular Pl uptake during the time of study, suggesting the presevation of membrane integrity of AMs under these conditions. At high doses of silica, however, a marked increase in Pl nuclear fluorescence was observed. Depletion of [Ca 2+] 0 greatly inhibited cellular Pl uptake, induced by 0. 1 mg/ml or higher doses of silica. This suggests that Ca 2 + influx, as a result of silica activation, is associated with cell injury. Indeed, our results further demonstrated that the low dose effect of silica on Ca 2+ influx is inhibited by the Ca2+ channel blocker nifedipine. At high doses of silica (>0.1 mg/ml), cell injury was not prevented by nifedipine or extracellular Ca2+ depletion, suggesting that other cytotoxic mechanisms, i.e., nonspecific membrane damage due to lipid peroxidation, are also responsible for the silica-induced cell injury. Silica had no significant effect on cellular ATP content during the time course of the study, indicating that the observed silicainduced (Ca2 ... ); rise was not due to the impairment of Ca2 + -ATPase pumps, which restricts Ca2+ efflux. Pretreatment of the cells with cytochalasin B to block phagocytosis failed to prevent the effect of silica on [Ca2+]; rise. Taken together, these results suggest that the elevation of [Ca2+]; caused by silica is due mainly to Ca2+ influx through plasma membrane Ca2+,channels and nonspecific membrane damage (at high doses). Neither ATP depletion nor Ca2+ leakage during phagocytosis was attributed to the silica-induced [Ca2+]; rise.

Nov 1, 1995

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960