Search Documents

By Joseph Cervik, Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. 5 mine. Methane from the over- lying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (1-5/8-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an under- ground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pct, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots."

Dec 1, 1942

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By B. J. Scheiner

Silver ores from the Candelaria District, Nevada, and Round Mountain District, Colorado, were investigated mineralogically and metallurgically. Silver minerals of four distinct groups were identified: (1) silver sulfide; (2) argentojarosite; (3) silver contained in the iron oxide; and (4) manganese carbonate-oxide minerals, Electrooxidation and acid-chloride leaching techniques were investigated as means of altering silver minerals, and their effects on subsequent silver extraction were determined. Application of the knowledge obtained from mineral leaching studies resulted in development of a sulfur dioxide-sodium chloride leaching sequence for extracting silver from these types of ores. Silver extractions of 80 to 85 percent were obtained by leaching the ores with a sulfurous acid-sodium chloride system. This was an increase of 9 to 61 percent silver extraction over that obtained by conventional cyanidation techniques.

Jan 1, 1973

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines to determine its effectiveness for recovering copper and silver from a tetrahedrite concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained coppers, silver, lead, zinc, antimony, and arsenic. Parameters affecting metal extraction (such as temperature, pressure, amount of ferrous chloride, and initial hydro-gen ion concentration) were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per square inch gage (psig) and 100° C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, antimony, arsenic, and sulfur reported to the tailings.

Jan 1, 1978

By D. E. Kirby

In the preparation of beryllium-copper alloys by fused-salt electrolysis, beryllium was electrowon from beryllium oxide dissolved in fluoride electrolytes and deposited on copper cathodes. At 880° to 1,030° C, deposition was on solid cathodes. Beryllium deposited on the copper, forming a liquid alloy that dripped from the cathode. Dripping alloys containing 3 to 4 weight-percent beryllium were produced with as high as 90 percent cathode current efficiency, by electrolysis at 910°.C. To prepare alloys of higher beryllium content, attempts were made at depositing beryllium on liquid copper cathodes. These efforts were generally unsuccessful, although alloys containing as much as 12 percent beryllium were prepared by this method. At temperatures of 1,100° to 1,300° C, requisite to maintaining beryllium-copper compositions as liquids, the beryllium reacted with cell structures.

Jan 1, 1972

By E. J. Gleim

"When permissible equipment is first placed in a gassy mine, those in charge may not realize the amount of attention and care they must give it if they intend to secure its full value as safety equipment. If permissible machines are installed as a safety measure, then they must receive regular, intelligent inspection and upkeep to forestall the development of unsafe features.Certain fundamentals have been followed in the design of this type of equipment in order to minimize the possibility of its igniting gas and dust. Hence, some knowledge of these fundamentals is essential to the inspector or official charged with the duty of ascertaining the condition of permissible machines with respect to safety. Familiarity with the constructional details of a machine is of first importance in making a thorough inspection of it. A knowledge of Schedule 2C3 which gives the requirements for practically all types of motor operated equipment receiving the United States Bureau of Mines' approval is also a requisite.There are certain special features in the construction followed by different manufacturers that can not be made clear for the purposes of inspection except by a lengthy description which would be inappropriate in this paper. There are, however, some general points that are applicable to the inspection of any machine employing trailing cable for connection to the power supply, also some that apply to any permissible storage-battery locomotive.The following list, based on the writer's experience in making field inspections, gives these general points in the form of questions which may he used as a guide by the inspector. A brief explanation is given after each question so that the reason for checking up on each point will be understood.1. Is a U. S. Bureau of Mines' approval plate attached to the machine? (Such a plate is necessary in order to establish identification as a permissible machine.)2. Is approval plate clean?(The plate should be clean so that the precautions enumerated on it are readable.)3. Is trailing cable protected by a fuse or other automatic circuit-interrupting device?(Trailing cable must have a fused trolley tap or other suitable means for short-circuit protection in case the cable is run over or splices fail. Proper fusing will minimize the possibility of fire in the cable reel.)4. If a trolley tap is used, does it contain a fuse of the proper capacity? (A piece of trolley wire or, too large a fuse may entirely defeat the purpose of fusing.)5. If a fused trolley tap is not used, how is connection made to the power supply? (The end of the trailing cable must be fitted with an insulated arrangement to minimize shock hazard when connecting the cable to the power supply.)6. Are the main fuses (or overload relays) of the correct size (or setting) for protection of the machine against overload?(Too large a fuse or too high a setting of the overload relay will permit damage to the machine by abuse through sustained overloads.)7. If the machine has a headlight, does the headlight circuit have overload and short-circuit protection?(The wiring of the headlight circuit on a machine is usually of a smaller size than that for the main circuits and therefore requires fuse protection proportionate to the size of wire.) Note: This same question may be asked relative to coal drills sometimes mounted on a machine."

Apr 1, 1932

By W. J. Pena, C. W. Owings

"Generally, the hazard of cool-dust explosions in tipples and cleaning plants is not given the consideration that is given it underground. This lack of consideration is probably due to failure to appreciate the potential hazard. An explosion in a tipple or cleaning plant is basically little or no different from an explosion underground. If bituminous-coal dust is raised into a cloud in the air and comes in contact with arcs from motor brushes, switches, or open flame, the dust is very likely to ignite, and flame will very probably propagate or extend through it if the quantity of dust per unit of air space is sufficient. The open space in a tipple or cleaning plant may reduce the violence of the explosion, but it is not likely to prevent ignition or propagation of flame.The movement of coal through a tipple or cleaning plant naturally puts into suspension a large amount of dust, which finally settles on exposed surfaces. Any disturbance that will put this dust into suspension in a sense enough cloud can result in the dust being ignited by an arc or open flame if one should be present. An explosion of bituminous-coal dust in a tipple or cleaning plant generally can be prevented either by keeping it thoroughly clean or by removing all sources of ignition, or both.The tests at the U.S. Bureau of Mines Experimental mine have shown that the explosibility of coal dust is proportional (other things being equal) to the ratio of the volatile matter to the volatile matter plus the fixed carbon, indicated thus:The volatile ratio for the Pittsburgh coal bed is calculated as follows:Therefore, as the volatile matter decreases the liklihood of ignition decreases; however, coal-dust explosibility depends on other factors also, such as fineness, dryness, and cloud density; and under some conditions other factors also intervene.Proof of the explosibility of coal dust in the absence of explosive gas has been shown in numerous cases in mines and mine plants and also by a series of tests. In these tests a dense cloud of dust is blown onto an open flame or an electric arc, almost invariably with resultant exploding of the dust. The Safety Division of the United States Bureau of Mines has made a number of demonstrations of the explosibility of Pittsburgh coal-bed dust, using a small gallery or box in which a cloud of coal dust is blown onto a lighted match; larger-scale tests have been made with an electric arc as the igniting agent. Bituminous-coal dust is readily ignited with a medium arc, but with low-volatile coals a larger arc is required. For test purposes, a 100-ampere arc has been used. Ignition has occurred readily under these conditions with Pocahontas No. 5 coal dust with ratios of volatile to total combustible of 0.232 to 0.253, and with Pocahontas No. 3 coal dust with a combustible ratio of 0.242. Lower Kittanning coal dust, with a ratio of 0.187, did not give definite ignitions, and Pocahontas No. 4 dust did not explode, although part of the coal-dust cloud ignited. It is probable that even the low-volatile coal dust will be found to be explosive with a higher-amperage electric arc as the initiating agent."

Jul 1, 1936

By E. H. Denny

"Reduction of mine accidents appears to depend upon essentially the same fundamentals, whether considered from the viewpoint of the mine operator, miner, State mine inspector, or safety engineer. Conditions of mine operation with respect to safety are governed in most States by a mining law, usually somewhat general in its provisions but more specific than laws dealing with other industries, Methods of mining development and practice evolved through experience have been handed down from generation to generation; many of these are intended to avoid injury to men and also loss of property. To carry out the intent of these bases of law and experience relating to safety supplemental measures and conditions are necessary. Among these may be: (1) Planned safety rules adapted to the mine and compliance by both officials and Miners with such of these rules as pertain to their work; (2) a supervisory force adequate and competent to ¬administer the mining laws and safety rules; (3) discipline adequate to secure compliance with safety measures; (4) safeguards against mechanical, electrical, falling, and other hazards; (5) mining operations planned with respect to safety of workers; (6) an active safety organization of officials and employees; (7) education of officials and employees in safety practices; and (8) an active sustained interest in safety by management and employees.This paper presents the viewpoint of the safety engineer, though a safety engineer connected with a specific mine or group of mines would be in a better position than the writer to present the industrial engineer's thought. The application of the mine safety fundamentals just outlined will be given consideration from observations of methods used by safety engineers and supervisors.The term ""safety engineer"" includes men of various duties, various degrees of experience, and various authority. Depending upon the size of the operation or the interest of the management in safety, the safety engineer may have accident prevention as his sole duty; he may be the head of a sizable safety organization; or he may be in part a claim agent; a statistician compiling figures for the enlightenment of the company, the public, or a mining institute meeting; a surveyor who must convince the miner that his scale of 10/10 equals 1 foot does not defraud the miner of 6 inches to every yard measured; or he may be by heaven¬ly gift an orator capable of assuring the employees that ""all's right with the world""; he may be a young engineer gaining, experience while checking the observance of company rules and investigating accidents; or he may have the physical ills frequently resulting from several decades of mining experience and instead of a pension, the position of safety engineer has fallen to his lot. He may have mine-operating authority to correct immediately a dangerous condition or practice or he may have his recommendations officially disregarded at the monthly meeting or when the bottom of the desk basket is reached. He is likely to find that his viewpoint on accident reduction is considered unsound today because of youth and inexperience and unsound later because of old age and senility. He is likely to find the easiest course to be that of attributing to Providence and the carelessness of the worker the mishaps that result in the removal of a man to the hospital or the morgue."

Dec 1, 1936

By A. B. Hooker, L. C. IlsLey

 Previous publications relating to permissible methane detectors covered investigations of the detectors from January 1922 to January 1,1937. All of these detectors are obsolete, or the designs have been modified under extensions of the original approvals. This report covers the investigations of detectors since January 1, 1937, including the present permissibility requirements as to design and performance and a brief description of each detector.

Apr 1, 1942

By James E. Bell

Quartz crystals occur on a farm in the vicinity of Laurel Fork, Carroll County, Va., in abundance over a large area, This has been known for several years, but no work had been clone, up to the Bureau of Mines examination in 1943, to determine the amount of crystalline quartz of usable quality. Field exploration was undertaken throughout the month of June 1943.

Jan 1, 1950

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

5. Development of Initial Probing System 5. 1 Introduction The preliminary evaluation of a variety of potential methods for initial probing showed that the optical system using closed circuit television (CCTV) and the sonar, or acoustic ranging, system were the most promising. The former is capable of pro¬viding a visual display of the mine passages in a clear, non-smoky environment, and the latter is capable of providing a map of the spatial location of the coal surfaces making up the entries, as well as objects, such as cribs, mining machines, etc., in the passages in both smoky and non-smoky environments. The sonar system used in conjunction with the CCTV in a clear environment can greatly assist in resolving the spatial distribution of objects seen on the TV screen. Further, in a smoky environment the interpretation of the sonar information could be facilitated if some visual information were also available. CCTV systems exist but require some modifications to suit this particular application. The Industrial Hazards and Communications Division of the Bureau has an ongoing program for the development of such a CCTV system. Rather than duplicate this effort in developing a CCTV system, it was decided to evaluate the possibility of utilizing their system for initial probing, while continuing with the develop¬ment of a system which would work in any environment, including the presence of dense smoke. The concept of using sonar for the initial probing of mine passages represents the application of new technology requiring development. The results of such a development effort undertaken during the course of this program are described in the following sections.

Jan 1, 1973

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

By Ε. P. YoUNGMAN

This paper presents one of a series of digests of foreign mining legis- lation and court docisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in vericis foreign countries. This interpretation of the laws - of Italy has been prepared, in part, from an aclysis made by John W. Frey, for merly associate mineral economist, U. S. Bureau of Mines. It incorporates addi- tional data and comments offered by Enrico Giobbe Della Pitta, a well-known Italian lawyer, in response to a questionnaire. These comments were forwarded by Harold H. Tittmann, American chargé d'affaires ad interim, at Rome, and trans- mitted to the Bureau of Mines through the courtesy of the Department of State.

Oct 1, 1930

By T. H. Ueng, S. D. Thompson, Y. J. Wang

"INTRODUCTION There is considerable interest among mining companies and government agencies in finding new ways to better control the generation and dispersion of respirable coal dust. Mine face ventilation generally has been considered the most effective tool for lowering the concentrations of respirable dust. Unfortunately, only a limited amount of research has been undertaken to determine the relationships between the various face ventilation parameters and the dust dispersion patterns. If these relationships are better understood, more efficient ways of controlling dust generation and dispersion may be evident. A practical and economical way to gain more in-depth understanding of these relationships is through scale model studies. Past research (1, 2, 3) has substantiated that scale models can be successfully used in studying ventilation parameters provided that geometric, kinematic, and dynamic similitues are maintained.To better understand face ventilation and dust dispersion, a 1/5 scale model of a room and pillar mine face was constructed. This model was then used to conduct experimental investigation on two ventilation parameters. The parameters which were examined included the line brattice distance from the face and the air quantity. The values of these parameters were varied in numerous experiments so that their effects on dust dispersion could be measured.The experiments of this study were unique in two ways. First, two different substances were used to simulate the respirable coal dust. Experiments were conducted with a tracer gas (methane) serving as the dust simulation substance. They were then repeated with an actual dust (Arizona Road Dust) replacing methane as the dust simulating substance. In previous scale model studies, the dust simulation substance has been limited to a tracer gas such as methane. The validity of using a tracer gas to simulate dust is not clearly known yet. The other unique thing about these experiments was the number of points measured for methane (or dust) concentration. Twenty five points in a grid arrangement were measured during each experiment of this study. The number of points measured for concentration in other studies has generally been very small (often 2 to 4). It is difficult to obtain an accurate assessment of how the ventilation parameters are effecting dust dispersion when only 2 to 4 points are measured."

Mar 1, 1989

By Robert W. Freedman

Vacutainers are used by the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) for sampling mine air and products of combustion. Tests were conducted on both 10-ml and 30-ml sizes to study shelf life stability during storage, pretreatment of stoppers, and handling of a wider range of compounds. A chamber was constructed to provide convenient, efficient evacuation of the Vacutainers shortly prior to use. Fixed gases and C1 ?C5 hydrocarbons could be stored for 1 week or more after sampling. Where decreases occurred (C02 and C3-C5 hydrocarbons), they were predictable as a function of storage time. An unexplained phenomenon, slow accumulation of CO in evacuated Vacutainers, occurred after a few weeks of storage. The levels were low and time dependent. Attempts to eliminate this behavior by pretreating the stoppers were unsuccessful.

Jan 1, 1976

To improve safety by making speed and direction control of a tracked vehicle simpler and instinctive. Approach A joystick control (which determines vehicle speed and direction of movement as well as the direction of any turning or pivoting) was developed and tested on a loading machine during a long-term underground demonstration. How It Works The control box actuated by the joystick lever contains two multiposition, multideck rotary switches. Fore-aft movement of the joystick rotates one switch through five positions to provide a neutral position and two speeds of travel in both

Jan 1, 1978