Search Documents

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By Charles D. Martens

Raw non fuel minerals produced in the United States during 1981 had an estimated value of $25 billion, about the same as that of 1980. In terms of 1980 dollars. the value of minerals produced during 1981 was $23 billion.2 This chapter includes tables for 1980 that were not available for publication in the 1980 Minerals Yearbook, but does not include the corresponding tables for 1981. The underlying causes of the overall decline in U.S. nonfuel mine production during 1981 were varied, but the common factor was the worldwide recession. In some cases the decline was traced to foreign competition. For example, iron ore production was lower in part because of increased imports of steel products such as coiled steel sheet. Another problem experienced by the domestic mining industry was the continuing difficulty in attracting capital. This was due in part to the attractiveness of investments outside the mining industry, such as short-term, high-interest securities. Another reason was the importation of commodities from countries where overall costs were lower because of such factors as high ore grade, lower taxes, lower wages, government subsidies, and less stringent safety and environmental regulations.

Jan 1, 1982

By A. L. Johns, M. V. Healey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of tie laws of Ecuador has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State..

May 1, 1930

The Bahamas Oil Refining Co. (BORCO) refinery in Freeport continued to operate at less than half its full 500,000-barrel-per-day capacity. Although owned through subsidiaries by the Carey Energy Corp (65%) and Standard Oil Co. of California (35%), BORCO is ineligible for participation in the Crude Oil Entitlements Program granted to companies operating within the United States proper or its territories. Like some other Caribbean refineries, BORCO has suffered a loss of normal market outlet due to the wt advantage afforded U.S. refineries by the Entitlements Program. Saudi Arabia, Nigeria, and Libya are the major suppliers of crude for the refinery. Its principal products, motor spirits, aviation fuel, distillate fuels, and residual fuel oils, were marketed in the United States and Puerto Rim. The Government-owned Bahamas Development Corp. and Burmah Oil Co. Ltd., held discussions pertaining to a renegotiation of Burmah Oil's management contract for the Grand Bahama Oil Transshipment terminal. The desired contract modifications were not made public but financial problems have plagued the terminal and its operation since construction started in 1972.

Jan 1, 1981

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By A. Visnapuu

High-grade synthetic rutile has been produced in the laboratory from domestic ilmenite concentrates by a new carbonyl process. The ilmenite was first reduced to convert the iron oxides to metal and then treated at temper-atures over 1000 C in high-pressure carbon monoxide (CO) to convert the iron to the pentacarbonyl. Rapid carbonylation was achieved in the presence of small quantities of selected promoters. Maximum iron removal occurred at temperatures between 110° and 130° C at CO pressures from 1,000 to 1,400 psig. Iron pentacarbonyl appeared as liquid and vapor in the reactor and could be removed by gravity flow and vapor transport. More than 90 pct of the iron was extracted in 2-hr experiments at pressures of 1,000 psig and above. The Ti02 product is porous owing to the removal of the iron, has the rutile crystal structure, and is suitable for chlorination. Waste disposal problems associated with the process would be minimal because the iron pentacarbonyl can be decomposed to produce iron powder or pellets for sale and CO for recycling.

Jan 1, 1973

By B. P. Martinez

This report presents the results of a research and development program in recovering waste-rolling oils conducted by the Bethlehem Steel Co., before 1954 at its Sparrows Point plant, Sparrow Point, Md., with the cooperation of the Bureau of Mines, U. S. Department of the Interior, College Park, Md. The objective of the program was twofold: First, to recover oil for reuse in the plant; and second, to stop pollution, by oil, of the stream and harbor areas in the immediate vicinity of the plant. The sequence of the investigations was laboratory and pilot plant studies on sedimentation, simple aeration, and flotation for the separation of oil and water; and construction of a production unit using standard flotation equipment. This work was only preliminary for the Bethlehem Steel Co. and it has continued research on this problem. Recent progress indicates that new, improved processes will soon replace the flotation units described in this report. The first efforts to separate oil and water by simple sedimentation were unsuccessful. To establish the cause of this failure, microscope examinations and measurements were made on cold-reduction rolling mill cooling-water effluents containing oil in suspension. It was discovered that an average oil globule, held in suspension, was only 0.001 inch in diameter and would not coagulate with other globules for normal sedimentation at room temperature. The next step in the sequence of studies was to coagulate the oil suspension by simple aeration with air under slight pressure. The aeration methods studied were effective in removing up to 68 percent of the total oil but were approaching flotation in principle. The final investigation of the series was flotation of the oil in conventional laboratory-size flotation cells. The small-bubble method, without reagents, floated up to 89 percent of the total oil held in suspension and was the process selected for pilot-plant development.

Jan 1, 1959

By H. H. Fukubayashi

This Bureau of Mines report describes the development of a pyrometallurgical process for the recovery of the zinc and lead contained in brass smelter flue dusts, which constitute a recycling or disposal problem. Tests on brass flue dust from several sources were made in a quartz tube, heated by an electric furnace to temperatures as high as 1,050° C. The dusts were mixed with carbon and heated in an oxygen-free atmosphere. It was demonstrated that 98 pct of the zinc and 12 to 25 pct of the lead, both in the metallic state, could readily be removed from the dusts. It was also found that 75 pct of the zinc could be recovered, with less than 0.1 pct of the lead, in the absence of chlorides. Pelletization techniques were investigated and 0.6 inch pellets were found to be optimal. Pelletizing results in a tenfold reduction in volume.

Jan 1, 1974

By A. J. Kraemer, O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (C. F. R. ) Committee of the Coordinating Research Council (C. R. C.) and the Bureau of Mines of the United States Department of the Interior . The first of these reports contained data on motor gasolines sold during the winter of 1935-36 and further reports on motor gasolines sold during the succeeding summers and winters to the summer of 1941

Dec 1, 1943

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

Develop improved blasting practices that can help to curb overbreak in highwalls at surface mines, thereby reducing the hazards of rock-falls to workers and equipment, The Problem The serious hazard in surface mining is the falling of rock from highwalls. Poor highwall stability is caused in part by geologic conditions, but often is aggravated by faulty blasting practices, where the explosive energy not only fractures the rock to be excavated, but also damages the rock that borders the excavation. This reduces the general stability of the hlghwall and increases the rockfall potential. The probability of injury to mine workers or damage to equipment associated with exposure to the highwall increases with the height of the highwall and the extent of its overbreakage. Most rockfalls occur in the first 15 days after a new highwall is exposed. This statistic is significant since most of the work below a highwall is done during this period. The area of greatest hazard is within 25 ft of the toe for rocks that fall vertically, and up to 90 ft from the toe for falling rocks that are deflected by the highwall during their descent, The workers most frequently involved in such accidents are dozer operators, ground laborers, and shovel operators or oilers.

Jan 1, 1985

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By Charles L. Kimbell

Bulk carriers, freighters, and tankers are the three classes of marine vessels engaged in transporting mineral commodities. However, vessels in each of these categories are not devoted wholly to mineral commodity transport. Bulk carriers move agricultural products as well as crude minerals and mineral fertilizers, as ore/bulk/oil carriers also do. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to moving nonmineral goods, as well as carrying mixed mineral and nonmineral cargoes. They include general cargo carriers, full containerships, partial containerships, roll-on/roll-off ships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels, such as sue, draft, crew requirements, and type of propulsion system, as well as fuel costs, have an undeniable influence on shipping industry performance, problems of and changes in the quantity and quality and types of material moved also significantly affect the shipping sector of the world economy. Unfortunately, comprehensive data in this regard are not available.

Jan 1, 1992

Develop a machine which can accurately simulate both the breathing and metabolic functions of a human being. The advantages of such a machine over a human being for testing of respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. Breathing simulation has been widely achieved throughout the world but metabolic simulation has not. Approach Utilize the latest computer technology and place the complex portion of the system in software, leaving the mechanical portion as simple as possible. How It Works The concept for the automated breathing and metabolic simulator (ABMS) was developed through a research contract with the Pennsylvania State University. The ABMS utilizes a continuous removal/replacement concept to simulate metabolic functions, with breathing and metabolic functions being controlled by a computer. The mechanical portion of the machine is simple; the complexity of the system lies in its computer software which is not subject to maintenance problems.

Jan 1, 1987

By R. S. Olsen

The Bureau of Mines is engaged in a continuing research effort toward the recovery of alumina from kaolinitic clay and other nonbauxitic domestic minerals. Hydrochloric acid extraction of calcined clay is among the acid processes under consideration. Although aluminum is easily leached from calcined clay, the presence of fines and slimes in the leached residue has hindered the application of this and other acid leaching processes. A clay feed preparation method was therefore developed that eliminated the slimy nature and the separation problems normally associated with leached clay residues. The preparation process consists of crushing the raw clay to minus 20 mesh, dampening the crushed clay with a fine water mist while tumbling on a rotating disk, and calcining the misted clay at 750° C. The misting process increases residue settling rates threefold to 9 cm/min (18 ft/hr) and filtration rates by two orders of magnitude. Leaching-kinetics were determined for misted clay feeds in a batch, stirred-tank reactor. Rapid leaching occurred during the first 85 to 90 pct of the extraction. The linear relationship of extraction to time during this initial phase corresponded to a zero order reaction with a rate constant of around 10 pct/min.

Jan 1, 1981