Search Documents

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By B. H. Eccleston

Experimental work is reported showing the effects of gasoline characteristics on auto emissions. Fuel volatility is shown to influence evaporative losses, with the higher losses associated with higher volatility. Fuel front-end olefin is shown to contribute significantly to reactivity of emissions. Large vehicle-to-vehicle differences were found. The study was conducted by the Bureau of Mines at its Bartlesville Energy Research Center in cooperation with the Coordinating Research Council Air Pollution Research Advisory Committee. The work was done using 15 1968-70 model autos and eight fuels were tested at ambients ranging from 20° to 95° F. Data on emissions from each vehicle-fuel-temperature combination are presented. Also included are calculated photochemical reactivity data and the distribution of hydrocarbon and nitrogen oxides during the test cycle.

Jan 1, 1972

By J. G. Croeni

The titanium-iridium alloy system was investigated to determine whether alloys of this system would merit further development as control-rod material for nuclear reactors. A study was made to determine the titanium-iridium phase diagram by using melting-point, thermal analyses, X-ray diffraction, dilatometric, electrical resistivity, and metallographic techniques. The titanium-iridium alloy system was investigated between 500° and 2,400° C. Results indicate the formation of two intermetallic compounds, Ti3Ir rind TiIr3, and one intermediate solid solution centered about the 50 atomic percent iridium composition. A eutectic reaction occurs at 1,475° C, and 19 atomic percent iridium. The Ti3Ir decomposes peritectically at 1,520° C. The intermediate solid solution exhibits a maxima of 2,140° C. at 50 atomic percent iridium. This phase is also believed to undergo an order-disorder transformation at 1,750° C. Another eutectic reaction takes place at 2,000" C. and 60 atomic percent iridium. The compound TiIr3 formed at 75 atomic percent iridium decomposes peritectically at 2,115° C. Further increases in iridium content result in the formation of an iridium-rich terminal solid solution. Information obtained below 900° C. in titanium-rich alloys indicates that iridium acts as a beta stabilizer in titanium, and the authors believe that a eutectoid decomposition of beta-titanium occurs near 500° C. and 10 atomic percent iridium.

Jan 1, 1962

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By J. Schlocker

The present emergency has greatly stimulated interest in the light metals - aluminum and magnesium - owing to their extensive use in airplane construction. The $63,000,000 plant being erected in the Las Vegas Valley by Basic Magnesium, Inc., under the auspices of the Defense Plant Corporation,

Jan 1, 1942

By J. E. Pahlman

One of the goals of the Bureau of Mines is to develop metallurgical pro-cesses that conserve energy and/or that take advantage of abundant domestic energy sources. Western lignites and subbituminous coals can be used for firing pellet induration and metallization furnaces. However, the refractory linings of these furnaces must be able to withstand attack from corrosive alkali metal oxides present in the ash of many of the low-rank fossil fuels. The Bureau of Mines conducted dynamic and static slag tests on high-alumina and alumina-silica refractories to determine their resistance to lignite ash slags. The investigations showed that increased alkali content in the lignite ash caused increased corrosion and erosion of the tested refractories. The degree of corrosion decreased with increasing alumina content, with the 99-percent-alumina refractories having the highest resistance. In general, the matrix phase was attacked preferentially to the alumina grains. Also, porosity reduction and tar impregnation enhanced the corrosion and erosion resistance. The 90-to 99-percent-alumina refractories are recommended for use as furnace linings in alkali slag environments.

Jan 1, 1979

By Dhaval Patel, Kim Witte, Charles Vaught, Michael T. Stephenson, Steve Booth-Butterfield, Cynthia Zuckerman, Brian L. Quick

This longitudinal field study was designed to encourage Appalachian coal miners in West Virginia and Pennsylvania to engage in hearing-protection behaviors. Method: Participants were mailed postcards that featured either a positive, negative, or neutral message on the outside of the postcard and a message encouraging hearing protection behaviors on the inside. The first posttest measurement of the effectiveness of the persuasive messages was conducted about a week after the postcards were mailed. The delayed posttest measurement was conducted six weeks later. Results: Responses from 307 coal miners revealed that the positive or neutral messages generated significantly more self-reported hearing protection behaviors than the negative message. Identical results were obtained in a delayed posttest assessment of miners' self-reported hearing protection behaviors. The positive message was also more effective than either the neutral or negative message in preventing defensive mechanisms from emerging over time. Impact on Industry: Positive and neutral messages were convincingly more than negative messages in facilitating self-reported hearing protection behaviors among coal miners. Similarly, the positive messages kept defensive processes at bay. Keywords: Hearing protection; Hearing loss; Coal miners; Campaign; Messages

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

By Michael S. Wieland

The work-principle from thermodynamics was used to formulate a model for predicting toxic fumes from mining explosives in underground chamber tests, where rapid turbulent combustion within the surrounding air noticeably changes the resulting concentrations. Two model constants were required to help characterize the reaction zone undergoing rapid chemical transformations in conjunction with heat transfer and work output: a stoichiometry mixing fraction and a reaction-quenching temperature. Rudimentary theory with an unsteady uniform concentration gradient was taken to characterize the combustion zone, yielding 75% for the mixing fraction. Four quenching temperature trends were resolved and compared to test results of ammonium nitrate compositions with different fuel-oil percentages (ANFO). The quenching temperature 2345 K was the optimum choice for fitting the two major components of fume toxicity: carbon monoxide (CO) and total nitrogen oxides (NOx). The resulting two-constant model was used to generate comparisons for test results of ANFO compositions with additives. Though respectable fits were usually found, charge formulations which reacted weakly could not be resolved numerically. The work-principle model yields toxic concentrations for a range of charge formulations, making it a useful tool for investigating the potential hazard of released fumes and reducing the risk of unwanted incidents. Keywords: Toxicity; Fumes; Explosives

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

The computer program has been developed in conjunction with the rest of the project to evaluate evacuation capabilities of the mines and develop guidelines for the escape systems. There are several problems associated with predicting evacuation performance of a mine. First, the mine has many interconnected passages, shafts, hoists and a number of miners in varying positions. To be able to predict evacuation time requires processing a hugh amount of data. A simplistic approach of determining the miner farthest from the exit and calculating evacuation time for him knowing his walking speeds and hoisting times is not realistic, since the waiting time for the hoist is neglected. The second problem is being able to repeat the calculations for a number of configurations. It may be possible to spend enough time to hand calculate the evacuation parameters for a single mine for a single configuration, but to evaluate capabilities of the evacuation

Jan 1, 1976

By I. A. Jacobson

In a closely controlled laboratory retorting system for oil shale, a relationship was developed by the Bureau of Mines between the temperature in the retort and the weight ratio of ethylene to ethane in the gases produced. Reciprocal temperature was shown to be directly proportional to the log ([ethylene]/[ethane]). From this relationship a number, called retorting index, was developed. The retorting index has the dimension of temperature, but its magnitude depends on both temperature and residence time for the reactants in the heated zone in the oil-shale retort. The slopes of the lines relating reciprocal temperature and the logarithm of the ethylene-ethane ratios are nearly constant for each of the retorting processes for which data have been presented. The retorting index should be a valuable tool to control the operation of oil-shale retorts, either aboveground or in situ. If an optimum operating condition can be established, the maintenance of the optimum or the departure from it should be easily monitored by use of the index.

Jan 1, 1974

By Fred Garcia, William P. Diamond

As part of its mine safety and health research program, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, has been investigating the geologic and mining factors influencing methane gas emissions associated with longwall mining. A primary focus of this research has been the consequences of increasing longwall panel dimensions, particularly face width, in gassy coalbeds. Continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). Average longwall pass methane emission rates for 229-m (750-ft) wide faces were 61 % (0.072 m31sec (153 cfm)) higher at the VP-3 Mine than at the VP-1 Mine. It was predicted by regression analysis of methane emissions data from 229-m (750-ft) wide faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7%, or 0.009 m3/sec (20 cfm), to 0.144 mysec (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces to 305 m (1,000 ft) at the VP-3 Mine would increase methane emissions by as much as 13%, or 0.029 mysec (65 cfm), to 0.268 dlsec (567 cfm).

Jan 10, 1999

The Federal Mine Safety and Health Act of 1977* defines respirable dust as dust measured with a device approved by the Secretary of Labor and the Secretary of Health and Human Services [30 USC 842(e)]. The approved sampler for respirable coal mine dust is the coal mine dust personal sampler unit (CPSU) [30 CFR 74; Jacobson 1971; Jacobson and Lamonica 1969]. The CPSU is generally called the 10-mm nylon cyclone, although the 10-mm nylon cyclone is actually just one component of the CPSU. The CPSU may either be mounted on a worker (with the sampling head positioned in the breathing zone for personal exposure monitoring) or in a fixed location for area sampling [Tomb 1990]. The CPSU consists of a pump unit, a sampling head assembly, and a battery charger if rechargeable batteries are used in the pump unit [30 CFR 74.2]. The sampling head assembly contains two stages. The first stage is a 10-mm nylon cyclone, which has collection characteristics similar to an elutriator. The amount of dust penetration depends on the flow rate [Jacobson and Lamonica 1969]. The second stage is a membrane filter (vinyl, pore size 5 pm) that collects the dust passing through the cyclone. The dust collected on the membrane filter is weighed to a precision (standard deviation) of 81 pg [Parobeck et al. 1981], and the respirable dust concentration in the mine atmosphere is then determined from the mass of dust collected and the volume of air sampled [Tomb 1990].

Jan 1, 1997

By Henry G. Dorsett

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 73 chemical compounds and mixtures, 29 drugs, 27 dyes, and 46 pesticides. Information is given on ignition temperatures of cloud and layer, minimum igniting energy, minimum explosive concentration, percent of inert dust required to prevent flame propagation, limiting oxygen concentration in the atmosphere to prevent ignition, and pressures and rates of pressure rise at dust concentrations of 0.1, 0.2, 0.5, 1.0, and 2.0 ounces per cubic foot. Explosibility indexes are computed where data are available to permit comparison of the relative explosion hazard. Variations of explosibility parameters with chemical composition are discussed. General means for minimizing the dust explosion hazard are reviewed.

Jan 1, 1968

By Donald I. Kurth

This Bureau of Mines report describes the development and application of a computer model of aquifer hydrology associated with in situ leaching of uranium. The model provides uranium resource developers with a simulation of leachant flow characteristics in a preproduction or pilot five-spot leaching operation. Various types of aquifers are modeled using closed form solutions of the partial differential equations describing the change in fluid head (pressure) as the leaching operation is carried out. User-supplied descriptive input consists of aquifer, well, and leachant flow characteristics. Numeric and graphic outputs such as isopressure, iso-velocity, and isotime contours are available. A typical application is shown.

Jan 1, 1978

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By J. J. Cummins

The Bureau of Mines heated at 150° to 350° C for 0.5 to 360. days Green River oil shale that had been previously extracted by benzene to provide information on in situ processing conditions, to determine the effect of low-temperature heating on the unconverted kerogen, and to determine the composition of benzene-soluble thermal products. The methods used in determining the composition of the soluble thermal products consisted of fractionation of the soluble material, elemental analysis of the soluble products, fractionation of the polar resins by ion-exchange chromatography, gas chromatographic analysis of [n]-alkanes3 and mass spectral analysis of the branched plus cyclic alkanes and aromatic oils. The methods used to determine the effect of low-temperature heating on the unconverted kerogen remaining in the oil shale heated residues consisted of carbon-hydrogen analysis, volatile material determination, carbon residue determination, and oxidation rate determination. In general, it was concluded that significant increases in the degradation of kerogen to oil occurred between the temperature range of 250° to 350° C; that the composition of the soluble products depends upon the temperature at which they are formed; and that the [n]-alkanes are pyrolytically degraded from the kerogen structure. In particular, the 250° C heating temperature is beneficial to the formation of branched plus cyclic alkanes. Also, the heated and unconverted oil shale kerogen and the soluble thermal products become more aromatic as the temperature increases from 150° to 350° C.

Jan 1, 1974

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987